Metra 99-7804B User guide

Brand: Metra

Model: 99-7804B

Type: User guide

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 3/17/2015 INST99-7804B

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

Installation Instructions for 99-7804B

• ISO DIN radio provision with pocket

• DDIN radio provision

• Painted two tone to match factory

• Retains factory color screen

• A) Radio housing trim panel • B) Brackets • C) Top bracket • D) Pocket • E) (6) White panel clips

• F) (8) #6 x 3/8” Phillips screws • G) (8) #8 x 3/8” Phillips screws • H) Display retention interface and harness (not shown)

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • Included

Antenna Adapter: • 40-HD11

• Panel removal tool • Phillips screwdriver

TOOLS REQUIRED

Honda Accord 2013-up

99-7804B

C D E

Dash Disassembly

– Honda Accord 2013-up .......................................2-3

Kit Assembly

– Kit preparation ..................................................... 4

– ISO DIN radio provision with pocket ...................... 5

– DDIN radio provision ............................................ 6

Wiring Instructions ............................................. 7-8

Touch Screen Instructions................................ 9-10

Table of Contents

99-7804B

Dash Disassembly

1. Unclip and remove the side trim

panels from each side of the

console. (Figure A)

2. Remove (2) Phillips screws

exposed on pocket then remove

the pocket. (Figure B)

3. Remove (2) 8 mm screws facing

up on bottom of radio chassis

inside pocket cavity. (Figure C)

4. Unclip and remove the small trim

panel between the radio and

steering column. (Models with auto

climate will have a thermistor hose

attached to this panel. Disconnect

the hose under the dash above the

gas pedal to give it enough slack

before re-installing the panel.)

(Figure D)

Continue on next page

(Figure A) (Figure C)

(Figure B) (Figure D)

99-7804B

Dash Disassembly

5. Remove (2) Phillips screws on top

of radio. (Figure E)

6. Unclip and remove the radio

assembly. (Figure F)

7. Remove (1) Phillips screw from

each A/C vent then unclip and

remove the vents. (Figure G)

8. Remove (2) Phillips screws

securing the hazard light switch

and retain for kit assembly.

Continue to kit assembly

(Figure E)

(Figure G)

(Figure F)

99-7804B

Kit Preparation

1. Attach the hazard light switch to

the radio trim panel using (2) of the

supplied #8 x 3/8” Phillips screws.

(Figure A)

2. Attach the (6) white panel clips to

the radio housing trim panel.

(Figure A)

Continue on next page

(Figure A)

99-7804B

ISO DIN radio provision with pocket

1. Attach the radio brackets to the

radio housing trim panel using (4)

of the #6 x 3/8” Phillips screws.

(Figure A)

2. Attach the top bracket to the top of

the radio brackets using (4) of the

#6 x 3/8” Phillips screws supplied.

(Figure B)

3. Mount the pocket to the bracket/

panel assembly with (4) of the

#8 x 3/8” Phillips screws supplied.

(Figure C)

4. Slide the radio into the assembly

and secure with screws supplied

with the radio. (Figure D)

5. Attach the A/C vents to the radio

trim panel and secure using (2)

of the supplied #8 x 3/8” Phillips

screws. (Figure E)

6. Locate the factory wiring harness

in the dash. Follow the Wiring and

Initialization section of this manual

before completing the installation.

7. Mount the new radio assembly into

the dash and reassemble dash in

reverse order of disassembly.

Kit Assembly

(Figure A) (Figure D)

(Figure B) (Figure E)(Figure C)

99-7804B

ISO DDIN radio provision

1. Attach the radio brackets to the

radio housing trim panel using

(4) of the #6 x 3/8” Phillips screws.

(Figure A)

2. Attach the top bracket to the top of

the radio brackets using (4) of the

#6 x 3/8” Phillips screws supplied.

(Figure B)

3. Slide the radio into the bracket/

trim panel assembly and secure

to the assembly using the screws

supplied with the radio. (Figure C)

4. Attach the A/C vents to the radio

trim panel and secure using (2)

of the supplied #8 x 3/8” Phillips

screws. (Figure D)

5. Locate the factory wiring harness

in the dash. Follow the Wiring and

Initialization section of this manual

before completing the installation.

6. Reassemble dash in reverse

order of disassembly.

Kit Assembly

(Figure C)(Figure A)

(Figure B) (Figure D)

99-7804B

Wiring Instructions

Harnesses Included:

• 24-pin gray Honda connector to 14-pin black interface connector, with

pre-wired 12-pin black ASWC-1 harness.

• 24-pin and 12-pin gray Honda connector to 22-pin black interface connector,

with a Yellow female RCA.

• 8-pin gray Honda subwoofer connector to White RCA.

• Blue connector to White connector LVDS cable.

Connections to be made:

From the 24-pin gray Honda connector to the aftermarket radio:

• Connect the Red wire to the accessory wire.

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• Connect the Blue/White wire to the amp turn on wire (this wire must be

connected to hear sound from the factory amplifier).

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

99-7804B

Wiring Instruction

Connections to be made:

From the 14-pin black connector to the aftermarket radio:

• Connect the Orange wire to the illumination wire. (If the aftermarket radio has

no illumination wire, tape off the Orange wire).

The following wires are for aftermarket multimedia/navigation radios that

provide these wires (if not required, tape them off and disregard them):

• Connect the Light Green wire to the parking brake wire (if applicable).

• Connect the Blue/Pink wire to the speed sense wire (if applicable).

• Connect the Green/Purple wire to the reverse wire (if applicable).

If not equipped with a factory Rearview Camera and one wants to be added:

From the 22-pin black connector to the aftermarket radio:

• Connect the Yellow RCA to the aftermarket rearview camera (female to female

barrel connector may be needed depending on camera brand, not provided).

Note: If an aftermarket backup camera is connected it must be selected

in the Menu. (Menu button on SWC>Camera Settings>Backup Camera

Source>Aftermarket Backup Camera)

If Equipped with Factory Subwoofer:

From the 8-pin gray Honda connector to the aftermarket radio:

• Connect the White RCA to the “Subwoofer Output”

(a Y-RCA adapter may be needed, not provided).

ASWC-1 (if installing)

• After the interface is initialized, plug the ASWC-1 into the 12-pin harness

of the 7804 and refer to the ASWC-1 instructions.

Note: There are a couple harnesses in the vehicle that there will be no

harness connections; these are not needed in the installation.

• Green and Gray connectors with similar small square connectors.

• 20-pin, 18-pin, & 5-pin gray connectors.

99-7804B

Touch Screen Instructions

When the interface first boots up, the

OEM screen will show an Android

Boot up sequence, DO NOT touch any

controls until the clock screen appears.

• Enter the System settings menu

to select the correct year range

for the vehicle; the instructions

to enter this menu are as follows.

Press the Menu button on the SWC

to enter the personalization menu

The steering wheel controls for the

personalization menu will override the

controls for the radio.

• Press the Menu button to enter the

personalization menu

To navigate through the menu you will

continue to use the steering wheel

controls.

then continue through the menus.

(System Settings>Others>Select

Car>2013 & 2014 Accord

OR 2015 Accord) If this step is not

done immediately after the boot

sequence, the interface will need

the power re-cycled by completely

unplugging the interface, waiting

5-10 seconds, and re-attaching

the harnessing.

The controls are as follows:

Volume up and down = Cycle

through the menu options

Source (SRC) = Enter

Seek left = Back or Return

Seek right = Not used

The personalization menu is the

same as the factory with a couple

differences.

Initialization Personalization Menu Procedure

99-7804B

Touch Screen Instructions

This menu option allows for a

background change on the clock, the

ability to adjust the clock, and select

the year range for interface.

This menu allows you to turn the

LaneWatch camera on and off, change

the view of the Rearview Camera, and

allow you to add a aftermarket camera

if the car is not equipped with a factory

rearview camera.

LaneWatch Calibration

Note: The LaneWatch button is

located on the left side of the

steering wheel, on the stalk.

• Press and hold the LaneWatch

button for 50 seconds to begin the

LaneWatch aiming procedure

(this procedure should only be

done by a Honda authorized

technician). At this point the

display will also show an image of

the LaneWatch camera feed, with

instructions on what to do — a

Honda authorized technician will

know what to do from here.

System Settings Camera Settings

99-7804B

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 3/17/2015 INST99-7804B

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certified technicians

Installation Instructions for 99-7804B

Metra 99-7804B User guide

Metra 99-7804B User guide

Related papers

Other documents