Metra 99-6520B User manual

APPLICATIONS

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 9/16/2014 INST99-6520B

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

INSTALLATION INSTRUCTIONS FOR PART 99-6520B

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Included interface retains factory 4.3” screen

•

Painted matte black to match factory finish

• A) Radio trim panel • B) Radio brackets • C) A/C button housing • D) Pocket • E) Console bracket

• F) (6) #8 x 3/8” Phillips pan-head screws • G) (2) White plastic panel clips • Axxess interface and harness (not shown)

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • Interface and harnesses included

Antenna Adapter: • 40-EU10 Multi-app antenna adapter

• Panel removal tool • Phillips screwdriver

• Socket Wrench • Torx Screwdriver

TOOLS REQUIRED

Dodge Journey 2011-up

(Models with 4.3” screen)

99-6520B

A

B C D E

G

Dash Disassembly

– Dodge Journey 2011-up ...................................2-3

Kit Assembly

– ISO DIN radio provision with pocket ...................4-5

– Double DIN radio provision ................................4-5

Axxess interface installation ..............................6-9

Table of Contents

F

99-6520B

2

Dash Disassembly

1. Unclip and remove the trim panel

along the top of the glove box over

to the passenger side a/c vent.

(Figure A)

2. Unclip and remove the small trim

panel to the left of the hazard

button. (Figure A)

3. Remove (2) Phillips screws

securing the climate/radio panel

then unclip and remove the panel.

(Figure B)

4. Remove (4) Torx screws securing

the radio chassis. (Figure C)

Continued on next page

(Figure A)

(Figure C)

(Figure B)

99-6520B

3

Dash Disassembly

5. Pull up on shift knob to remove

(Figure D).

6. Unclip and remove the shifter trim

panel including the cup holders

from the top of the center console.

(Figure E)

(Figure D) (Figure F)

(Figure E)

7. Push down and then pull back and

out on the pocket in the front of

the console. Tip: You may need

to pull the console side panels

outward at the same time as

pulling out on pocket. (Figure F)

8. Remove the (2) metal panel clips

on the front side of the pocket and

save for kit assembly.

Continue to kit assembly

99-6520B

Kit Assembly

4

1. Attach the console bracket to the

back of the A/C button housing

using (4) of the provided #8 x 3/8”

Phillips screws. Figure A

2. Install the (2) metal panel clips

saved from the pocket disassembly

onto the console bracket Figure A

3. Secure the A/C button housing into

the pocket space in the front of the

center console. Figure B

4. Attach the provided clips to the

radio trim panel. Figure C

(Figure A)

(Figure B)

(Figure C)

99-6520B

Kit Assembly

5

ISO DIN radio provision with pocket

1. Mount the pocket to the radio

brackets with (2) #8 x 3/8” Phillips

screws supplied. Note – Pins on

brackets will align with front

mounting hole of pocket.

Figure A

2. Slide the aftermarket radio into the

radio bracket/pocket assembly and

secure with the screws supplied

with the radio. Figure B

3. Locate the factory wiring harness

and antenna plug in the dash.

Refer to the Axxess Interface

Wiring section of this manual.

4. Mount the new radio/pocket

assembly into the dash and

reassemble dash in reverse order

of disassembly using the

99-6520B radio trim panel.

Double DIN radio provision

1. Break the small locating pin from

the inside surface of each bracket.

Figure A

2. Mount the DDIN radio to the radio

brackets using the screws supplied

with the radio. Figure B

3. Locate the factory wiring harness

and antenna plug in the dash.

Refer to the Axxess Interface

Wiring section of this manual.

4. Mount the new radio assembly into

the dash and reassemble dash in

reverse order of disassembly using

the 99-6520B radio trim panel.

(Figure A) (Figure A)

(Figure B)

Remove pin

99-6520B

6

• Provides accessory (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Used in non-amplified systems

• Provides NAV outputs (parking brake, reverse and V.S.S.)

• Prewired ASWC-1 harness included (ASWC-1 sold separately)

• High level speaker input

• Micro “B” USB updatable

• Retains balance and fade

• Ability to add aftermarket backup camera and additional video input

• Retains OE screen

FEATURES

• Cutting tool • Crimping tool • Tape

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

• Interface • 16-pin harness with stripped leads

• 18-pin harness to 22-pin Chrysler harness with stripped leads

• 40-pin climate extension cable

INTERFACE COMPONENTS

From the 16-pin harness to the aftermarket radio:

• Connect the (2) Red wires to the ignition wire.

• Connect the Orange/White wire to the illumination wire. If the aftermarket

radio has does not have an illumination wire, tape off the Orange/White wire.

• Connect the Blue/White wire to the radio’s amp turn on wire.

• Tape up and disregard the Brown wire, it will not be used in this application.

The following wires are for the multimedia aftermarket radios that have

navigation/video built in.

• Connect the Light Green wire to the parking brake wire.

• Connect the Blue/Pink wire to the VSS or speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

• Plug the 16-pin harness into the interface.

Note: The following wires on the 16-pin harness are not used in this application.

Purple • Purple/Black • Green • Green/Black • White • White/Black • Gray • Gray/Black

Connections to be madeAxxess Interface Installation

99-6520B

7

From the 18-pin harness:

• Connect the Yellow RCA labeled (1) to either a backup camera

(sold separately), or a video source.

• Connect the Yellow RCA labeled (2) to either a backup camera

(sold separately), or a video source.

Note: It does not matter what RCA you use as they are programmable.

• Plug the 18-pin harness into the interface.

Note: The following wires on the 18 pin harness are not used in this application.

Purple • Purple/Black • Green • Green/Black

Connections to be made

From the 22-pin harness to the aftermarket radio:

• Connect the Yellow wire to the battery or memory wire.

• Connect the Black wire to the ground wire.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

• Plug the 22-pin harness into the interface.

From the 12-pin harness to the aftermarket radio:

• The 12-pin harness is to be used in conjunction with the optional ASWC-1

(not included) to retain steering wheel controls. If the ASWC-1 is not being used,

disregard this harness. If it will be used, please refer to the ASWC-1

instructions for programming.

Note: The white 40-pin harness from the factory must be connected to

the 99-6520B for the climate to function. We have included a 40-pin

extension cable to ease in installation.

99-6520B

Screen operation

1. Radio button – Show the current time

2. Player button – Toggles between Video 1 and Video 2 when input is activated

3. Climate button – Takes you to the climate screen

4. Setting button – Takes you to the setting screen

5. More button – Shows the outside temperature and current time

6. Screen Off – Turns the display off

1

2

3

4

5

6

8

• With all connections completed to the aftermarket radio, plug the 22-pin

harness into the vehicles wiring harness.

• Reconnect the negative battery terminal.

• Cycle the key, by turning the ignition on for 30 seconds. Then off and on again

to test the radio.

• Turn the ignition on if not already, and then turn the radio on to verify that the

radio works. Check balance and fader controls for proper operation.

• To adjust the overall volume of your audio system, rotate the potentiometer

which is located on the 16-pin side of the interface clockwise. (this is only done

if the vehicle is amplified).

Testing the Interface

Installing the Interface

99-6520B

9

Video option screen

2. From here select Video 1 or

Video 2. Once in the screen you

can select to make each video

input an AUX input, Backup

Camera input, or Not Used.

Note: The Backup camera input is

controlled by data and will activate

when you put the vehicle in reverse.

Note: The AUX video is controlled

by data and will only work when the

vehicle is in park.

1. Once in the setting screen

scroll down until you see the

Customize button. Tap the screen

and it will take you to the video

option screen.

3. After you have made your section tap the “Done” button located on the upper

left hand corner of the screen to exit.

Pressing the “About” button will

display the current version number

and vehicles VIN number.

Page is loading ...

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 9/16/2014 INST99-6520B

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certified technicians

INSTALLATION INSTRUCTIONS FOR PART 99-6520B

Page is loading ...

INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-6520B

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

RREV. 9/16/2014 INST99-6520B

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recomienda técnicos

con certificación del Programa

de Certificación en Electrónica

Móvil (Mobile Electronics

Certification Program, MECP).

EL CONOCIMIENTO ES PODER

Mejore sus habilidades de instalación y fabricación

inscribiéndose en la escuela de dispositivos electrónicos

móviles más reconocida y respetada de nuestra industria.

Regístrese en www.installerinstitute.com o llame al

800-354-6782 para obtener más información y avance

hacia un futuro mejor.

Metra 99-6520B User manual

Related papers

Other documents