Powerware Security Detector
User’s Guide
®
Powerware is a registered trademark of Eaton Electrical Inc.
ECopyright 2007 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
EATON Powerware
®
Security Detector User’s Guide S 164201679 Rev 1
3
Security Detector
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the security detector. Please read all instructions before operating the
equipment and save this manual for future reference.
The security detector is a device that works with the Eaton Powerware
Environmental Rack Monitor (ERM) and connects to the TH-Module.
Through the ERM, the user can monitor if a door or window is open.
Security detectors are commonly used in burglar alarm systems as
door/window open sensors; however they can be disabled if they are in
a strong, external magnetic field. If a security detector is dropped onto a
hard surface from more than 30 cm (11.8”) or subject to shock of more
than 30G, it is possible to cause the characteristics to change (Pull-in,
Drop- out, etc.).
It is recommended to place security detectors in doors or windows.
Installation
To install the security detector:
1. Loosen the screws on the TH-Module (see Figure 1).
Alarm 1 Alarm 2
Figure 1. Adjusting TH-Module Screws
SECURITY DETECTOR
EATON Powerware
®
Security Detector User’s Guide S 164201679 Rev 1
4
2. Connect the security detector wires to the TH-Module alarm 1 or
alarm 2 connectors, and then tighten the screws on the TH-Module
(see Figure 2).
Figure 2. TH-Module with Security Detector
3. Remove the backing from the security detector sensors and stick
the sensors to the door and doorframe or the window and
windowframe.
4. If you are installing additional security detectors, repeat Steps 1
through 3.
5. Connect the RJ-45 network cable to the TH- Module port labeled
“010101“ (see Figure 3).
Figure 3. Connecting the RJ-45 Network Cable
SECURITY DETECTOR
EATON Powerware
®
Security Detector User’s Guide S 164201679 Rev 1
5
6. Connect the other end of the RJ-45 network cable to the ERM (see
Figure 4).
TH-Module
12
TH-Module-1 TH-Module-2NETWORK
RESET
12 VDC
To LAN port To Power Outlet
ERM
Figure 4. ERM and TH-Module
7. Verify that the ERM is connected to the network. Open the ERM
Web page and select Monitoring, then TH-Module-1 Setup or TH-Module-2
Setup
. The setup screen displays (see Figure 5).
8. Change the status of the TH-Module from “Disable” to “Auto” on
the Device Name line. Verify that the TH-Module LED
(Power/Status) is flashing.
9. Set the status of alarm 1 and/or alarm 2 to “Normal Close” and
select “Door Contact.”
10. Select
Set Value to confirm the security detector setup.
SECURITY DETECTOR
EATON Powerware
®
Security Detector User’s Guide S 164201679 Rev 1
6
Figure 5. Security Detector Settings
11. When the sensor detects the door or window open, the ERM Web
page displays the alarm. The Web page for the alarm table and
sensor events also records the alarm.
Figure 6. Comprehensive View Screen
Figure 7. Events Log Data
Figure 8. Alarm Table
NOTE For more detailed information that is not included in this manual, first register your
product at warranty.powerware.com, then visit our Web site:
www.powerware.com/rackmonitor. You can also download firmware upgrades, the latest
manuals, and other documentation.
*1642016791*
164201679 1
/