GTO I6H-LP6110KP User manual

rev - 10/30/17

Moving Gate

Area

Driveway

10'

NEVER INSTALL

any control device

within gray area

NEVER install the keypad portion of this

system where a person can reach through

the gate to activate it, or where a person can

touch the gate while activating the keypad.

The recommended minimum distance

between the gate and keypad is 10 ft.

Printed in China for GTO

Wireless Estate Intercom

Installation Manual

Kit Includes:

A. Keypad

B. Keypad Cover

C. Jumper (required for hard-wired installation)

D. Keypad Battery Cover

E. Base Unit

F. Base Unit Rechargeable Battery

G. Transformer

H. Screws for mounting Keypad Cover

How it Works:

A visitor without an entry code presses the CALL button on

the keypad. The base (indoor) unit and the keypad will ring.

A user at the base (indoor) unit answers the call by pressing

the PUSH TO ANSWER/TALK button. The user at the base

unit then presses the GRANT PERMISSION button to allow

the visitor to operate the gate. The keypad’s GRANTED

light comes on, indicating that the visitor can now push any

number key on the keypad to open the gate.

Visitors with access codes simply use their code to operate

the gate. Temporary codes can be programmed to expire

within a set number of days.

WIRELESS

PROFESSIONAL RESIDENTIAL

ACCESS

SYSTEMS

WARNING

GTO Access Systems, LLC • 3121 Hartsﬁeld Road • Tallahassee, Florida 32303

Telephone (850) 575-0176 • Fax (850) 575-8912 • www.gtoinc.com • www.gtoaccess.com

Estate Intercom/Keypad Features

Keypad

• The keypad illuminates and beeps at the press of any key. At night, the keypad will illuminate when the proximity sensors

detect motion near the keypad face.

• When a valid code is entered, the STATUS light will blink rapidly, the keypad will beep three times, and the GRANTED

light turns green.

• The keypad remains active for 40 seconds after entering a valid code: pressing any key on the keypad while the gate is

in motion will stop the gate; pressing any key while the gate is stopped will cause the gate to reverse direction. After 40

seconds, the keypad will

beep 3 three times and go into “idle” mode, and the GRANTED light will turn off.

• If more than 20 key presses are entered without matching an Entry Code, the STATUS light will ﬂash rapidly, an error tone

will sound for 1 second, and the keypad will go into “lock-down” mode for 40 seconds.

• If more than 10 seconds elapse between key presses, the keypad will beep 3 three times and go into “idle” mode.

Master and Entry Codes

• Up to 100 Entry Codes may be programmed into the keypad.

• Temporary Entry Codes can be programmed to expire within one to seven (1–7) days.

• Entry Codes remain stored in memory even when the keypad batteries go dead.

• All Entry Codes are deleted by pressing the RESET button on the keypad; Master Code defaults to “1234.”

Base Unit

• The base unit is powered by a rechargeable battery (included); the charge is maintained by the transformer.

• The base unit can be disconnected from the transformer allowing it to be moved anywhere within range.

• Up to three additional base units can be added to the system.

NOTE: The keypad, not the base station, initiates the call and operates the gate. The base station is for answering

calls and granting “permission” for the gate to be opened.

INTERCOM/KEYPAD SPECIFICATIONS

Frequency 318 MHz from keypad to gate opener

915 MHz from keypad to base station

Memory – Keypad Stores up to 100 four-digit entry codes

Power Consumption – Keypad 60 mA when relay is closed

Power Supply – Keypad Four C batteries (plus 8-24V DC/AC for hard-wired installations)

Power Supply – Base Unit 9 Vdc 300 mA transformer; 3.6V Ni-MH 800 mA rechargeable battery

pack

Range from Keypad to Base Unit 500’ wireless

Range from Reypad to Gate Opener 50’ wireless 100’ wired using 16 AWG wire

Relay Output – Keypad Momentary, normally open dry contact closes for 2 seconds upon

activation

Relay Output Rating – Keypad 12 or 24 Vdc 100 mA

Wiring – Keypad Power & Relay Output 16 AWG stranded low voltage direct burial wire

Keypad and Base Unit Overview

Front

Interior

Calling Light:

7XUQV5('ZKHQFDOOLQJWXUQV

*5((1ZKHQFDOOLVDQVZHUHG

Granted Light:

7XUQV*5((1ZKHQDFFHVV

SHUPLVVLRQLVJUDQWHG

Program Button:

8VHGWRSURJUDP(QWU\&RGHV

Status Light:

%OLQNVRQFHZKHQDQ\NH\LV

SUHVVHGSURYLGHVYLVXDOIHHGEDFN

ZKHQSURJUDPPLQJNH\SDG

DEF

WXY

MNO

CALL

GHI

PRS

ABC

TUV

JKL

Presence

Sensors

123456789

ETD

ID SET RESET

REQUIRES 4 “C”

SIZE BATTERIES

123456789

ETD

ID SET RESET

REQUIRES 4 “C”

SIZE BATTERIES

Relay Output:

8VHGWRFRQQHFWWKHNH\SDGWRJDWH

RSHQHUFRQWUROERDUGKDUGZLUHG

LQVWDOODWLRQV

Power Input:

7RFRQQHFWNH\SDGWRJDWHRSHQHUSRZHU

VRXUFHKDUGZLUHGLQVWDOODWLRQV

DIP Switches:

0DWFKNH\SDG',3VZLWFKVHWWLQJVWR

(QWU\7UDQVPLWWHU¶V',3VZLWFKVHWWLQJV

Jumper:

2)):LUHOHVVPRGH0+]HQDEOH

215HOD\RXWKDUGZLUHGLQVWDOODWLRQV

0+]GLVDEOH

Reset Button:

3UHVVWKLVEXWWRQIRUVHFRQGVWR

SURJUDPNH\SDGWR0DVWHU&RGHGHIDXOW

³´DQGGHOHWHDOORWKHUFRGHV

ID Set Button:

8VHGWRV\QFDGGLWLRQDOEDVHXQLWVZLWK

NH\SDG

Battery Holder and Cover:

8VH³&´EDWWHULHV

Face

POWER

Keypad

Batt Low

Grant Permission

Push To Answer/Talk

End Call

DV 9V

Power Light:

*5((1FKDUJLQJ5('EDWWHU\

SRZHUPRGHXQSOXJJHGIURP

WUDQVIRUPHU%OLQNLQJ5('ORZ

EDWWHU\

Push To Answer/Talk Button:

7RDQVZHUFDOOIURPNH\SDGSUHVV

DQGKROGWRWDONUHOHDVHWROLVWHQ

Grant Permission Button:

0XVWEHSUHVVHGEHIRUHWKHSHUVRQ

DWWKHNH\SDGFDQSUHVVDQ\NH\WR

RSHQWKHJDWH

End Call Button:

7HUPLQDWHVWKHFDOO

Keypad Battery Indicator

Light:

21ZKHQNH\SDGEDWWHU\LVORZ

Power Jack:

Connect transformer to charge the

EDWWHU\

ID SET

VOLUME

POWER

OFF

Volume Control:

&RQWUROVYROXPHOHYHORIVSHDNHU

Battery Access Cover:

5HFKDUJHDEOH9ROW1L0+EDWWHU\

LQFOXGHG

ID Set Button:

8VHGWRV\QFDGGLWLRQDOEDVHXQLWVZLWK

NH\SDG

ON/OFF Switch:

7XUQ2))WRFRQVHUYHEDWWHU\SRZHU

Bottom

1. Install Keypad and Base Unit Batteries

Step 1:8QORFNWKHERWWRPRIWKHNH\SDGDQGVHSDUDWHLWIURPLWVFRYHU5HPRYHEDWWHU\FRYHUDQGLQVWDOOIRXU³&´EDWWHULHV

requiredQRWLQFOXGHG5HSODFHWKHEDWWHU\FRYHU

Step 2:5HPRYHWKHEDVHXQLWEDWWHU\FRYHUXVLQJDVPDOOSKLOOLSVKHDGVFUHZGULYHU,QVWDOOWKHUHFKDUJHDEOH1L0+EDWWHU\

LQFOXGHG5HSODFHEDWWHU\FRYHU

ID SET

2. Connect the Transformer and Test Base Unit

Step 1:

)LQGDFRQYHQLHQWORFDWLRQQHDUDQ$&RXWOHWWRPRXQWRUSODFHWKH

EDVHXQLW

Step 2:

3OXJWKHWUDQVIRUPHULQWRWKHRXWOHWDQGFRQQHFWLWWRWKHEDVHXQLW

7KHEDVHXQLWFDQEHGLVFRQQHFWHGIURPWKHWUDQVIRUPHUIRUXVHLQ

DQRWKHUORFDWLRQ7KHEDWWHU\ZLOOODVWDSSUR[LPDWHO\IRXUKRXUVZKHQ

XQSOXJJHGIURPWKHWUDQVIRUPHUYou can turn the base unit OFF to

conserve battery power, however it will not receive a signal.

Step 3:

7HVWWKHEDVHXQLWE\SUHVVLQJWKH&$//EXWWRQRQWKHNH\SDG7KH

EDVHXQLWZLOOULQJ

Charge battery for 12 hours

before using the system for

the ﬁrst time.

POWER

Keypad

Batt Low

Grant Permission

Push To Answer/Talk

End Call

DV 9V

Transformer

110 Vac outlet

3. Install and Test Keypad

For wirelessDSSOLFDWLRQVWKHNH\SDGmustEHLQOLQHRIVLJKWRIandQRPRUHWKDQIWDZD\IURPWKHJDWHRSHQHU

UHFHLYHU7HVWWKHNH\SDGUDQJHEHIRUHSHUPDQHQWO\PRXQWLQJLW

Step 1:$WWKHJDWHVHWWKHNH\SDG',3VZLWFKHVWRPDWFK\RXU

(QWU\7UDQVPLWWHU¶V',3VZLWFKVHWWLQJVNOTE: If you have not

adjusted your gate opener’s Entry Transmitter from the factory

setting, see the “Personalize Transmitter Settings” section in your

gate opener’s installation manual.

Step 2:7HVWWKHNH\SDGXVLQJWKHGHIDXOW0DVWHU&RGH³´,W

ZLOODFWLYDWHWKHJDWH

Step 3:7HVWWKHNH\SDGUDQJHE\SUHVVLQJWKH&$//EXWWRQ<RX

ZLOOKHDUWKHEDVHXQLWULQJLQJWKURXJKWKHNH\SDGVSHDNHU

Step 4:0RXQWWKHNH\SDGFRYHUXVLQJWKHVFUHZVSURYLGHG

NOTE: a metal housing or metal object can affect range

Step 5:6OLGHWKHNH\SDGLQWRWKHFRYHUDQGORFNLW

You will need to hard-wire your keypad to the gate opener if you:

• Do NOT have a GTO Entry Transmitter.

• Have a GTO Access Systems GP Series gate opener.

• Live in an area with high radio frequency interference.

Skip to page 5 for instructions.

123456789

ETD

ID SET RESET

If you use this button

to operate gate, put

the 9th DIP Switch

in the “0” position

Dual Button Entry Transmitter

1 2 3 4 5 6 7 8 9

ECE

A23S 12V

ALKALINE BATTERY

–

LED

Single Button Entry Transmitter

If you use this button

to operate gate, put

the 9th DIP Switch in

the “+” position

Change the Keypad’s DIP Switch Settings NOT

the Entry Transmitter Dip Switch Settings

Program New Master Code

1. Press and Release Program Button:

2. Enter current Master Code:

(example: the factory default Master Code)

3. Press and Release Program Button:

4. Enter the Function Code:

5. Press and Release Program Button:

6. Enter the new Master Code:

7. Press and Release Program Button:

8. Enter the new Master Code again:

9. Press and Release Program Button:

Program Button

Status Light

= Your 4-digit code.

4. Program the Keypad

• A Master Code is needed to add, remove, or program Entry Codes.

• Factory default Master Code is “1234.”

• Keypad can only enter “program” mode from “idle” mode.

• Keypad will beep three times before going into “idle” mode (more than 10 seconds

between key presses).

Add New Entry Code

2. Master Code

4. Function Code

6. New Entry Code

Delete Entry Code

2. Master Code

4. Function Code

6. Code to be deleted

Delete All Entry Codes

2. Master Code

4. Function Code

Add Temporary Entry Code

*In step 4, you will need to enter a number from 1 through 7

to indicate the number of days until the Entry Code expires.

2. Master Code

Function Code & # of days Code will be active*

6. Temporary Entry Code

Programming Confirmed: Keypad will beep 3 times.

Error Message: Status light will flash rapidly, error tone will sound for

1 second and keypad will return to “idle” mode (changes not saved).

• Entry Code is not 4 digits.

• New Master Codes don’t match (“Program New Master Code”).

• Memory is full (already 100 codes).

• No matching code is found (“Delete Entry Code”).

5. Sync Additional Base Units (optional)

,I\RXSXUFKDVHGDGGLWLRQDOEDVHXQLWV)0%&\RXPXVWV\QFHDFKDGGLWLRQDOXQLWZLWKWKHNH\SDGVRWKH\FDQ

FRPPXQLFDWH

Step 1: ,QVWDOOWKHEDWWHU\DQGWXUQWKHEDVHXQLW21

Step 2: 3UHVVDQGUHOHDVHWKH³,'6(7´EXWWRQRQWKHNH\SDG

Step 3: 3UHVVDQGUHOHDVHWKHQXPEHURQWKHNH\SDGWKDW

FRUUHVSRQGVWRWKHEDVHXQLW\RXDUHDGGLQJ<RXZLOOKHDUD

QXPEHURIEHHSVFRUUHVSRQGLQJWRWKHQXPEHU\RXSUHVVHG)RU

H[DPSOHLI\RXDUHDGGLQJDVHFRQGEDVHXQLWWRWKHV\VWHPSUHVV

³´WKHNH\SDGZLOOEHHS7:2WLPHV,I\RXDUHDGGLQJDWKLUG

EDVHXQLWSUHVV³´WKHNH\SDGZLOOEHHS7+5((WLPHVHWF

Step 4: 3UHVVWKH³,'6(7´EXWWRQRQWKHEDVHXQLWXQWLOLWEHHSV

WKHQUHOHDVH<RXZLOOKHDUEHHSVIURPWKHEDVHXQLWDQGEHHSV

IURPWKHNH\SDGZKLFKPHDQVWKHEDVHXQLWDQGNH\SDGDUH

V\QFHG

IMPORTANT: Base units need to be placed at least 10 feet

apart to prevent interference

6. Test the Intercom

IMPORTANT:7KHEDVHXQLWDQGWKHNH\SDGFDQQRWEHZLWKLQIHHWRIHDFKRWKHUZKHQRSHUDWLQJ,IXQLWVDUHFORVHU

WKDQIHHWWKHVLJQDOZLOOEHLQFRQVLVWHQWDQGHPLWIHHGEDFN

+DYHVRPHRQHSUHVVWKH&$//EXWWRQRQWKHNH\SDG:KHQWKHEDVHXQLWLQVLGHWKHKRXVHULQJV

SUHVVWKH$16:(5

EXWWRQDQGWDONWRWKHSHUVRQDWWKHJDWHWRFKHFNWKHFRQQHFWLRQDQGUDQJH7KHQSUHVVWKH*5$173(50,66,21EXWWRQ

DQGKDYHWKHSHUVRQSUHVVDQ\NH\RQWKHNH\SDGWRDFWLYDWHWKHJDWH

Using the Wireless Estate Intercom

NOTE: The keypad, not the base station, initiates the call and operates the gate. The base station is for answering calls

and granting “permission” for the gate to be opened.

Using the Intercom

  3UHVVWKH&$//EXWWRQRQWKHNH\SDGWRULQJWKHEDVHXQLWLQVLGHWKHKRXVH

  7KHEDVHXQLWZLOOULQJZKHQLWUHFHLYHVD&$//IURPWKHNH\SDGKROGWKH$16:(5EXWWRQWRWDONWRWKHYLVLWRU

UHOHDVHWKH$16:(5EXWWRQWROLVWHQ3UHVVWKH*5$173(50,66,21EXWWRQWRDOORZWKHYLVLWRUWRRSHQWKHJDWH

E\SUHVVLQJDQ\QXPEHUNH\RQWKHNH\SDG7KH(1'&$//EXWWRQWHUPLQDWHVWKHFDOO

  $IWHUWKHNH\SDG¶V*5$17('OLJKWWXUQVJUHHQSUHVVDQ\QXPEHUNH\WRRSHQWKHJDWH

Using Entry Codes

  :KHQDYDOLGFRGHLVHQWHUHGWKH67$786OLJKWZLOOEOLQNUDSLGO\DQGWKHNH\SDGZLOOEHHSWLPHV

  7KHNH\SDGUHPDLQVDFWLYHIRUVHFRQGVDIWHUHQWHULQJDYDOLGFRGHSUHVVLQJDQ\NH\RQWKHNH\SDGZKLOHWKHJDWHLV

LQPRWLRQZLOOVWRSWKHJDWHSUHVVLQJDQ\NH\ZKLOHWKHJDWHLVVWRSSHGZLOOFDXVHWKHJDWHWRUHYHUVHGLUHFWLRQ$IWHU

VHFRQGVWKHNH\SDGZLOO

EHHSWKUHHWLPHVDQGJRLQWR³LGOH´PRGH

  ,IPRUHWKDQNH\SUHVVHVDUHHQWHUHGZLWKRXWPDWFKLQJDQ\(QWU\&RGHVWKH67$786OLJKWZLOOÀDVKUDSLGO\WKH

HUURUWRQHZLOOVRXQGIRUVHFRQGDQGWKHNH\SDGZLOOJRLQWR³ORFNGRZQ´PRGHIRUVHFRQGV

  ,IPRUHWKDQVHFRQGVHODSVHEHWZHHQNH\SUHVVHVWKHNH\SDGZLOOEHHSWKUHHWLPHVDQGJRLQWR³LGOH´PRGH

Intercom ID Codes

This keypad and base unit are synced at the factory to communicate with each other. This

base unit is considered to be “unit #1” when adding more base units to the system.

ID SET button

ID SET

VOLUME

POWER

OFF

Keypad - Inside

Base Unit – Bottom

Keypad - Front

ID SET button

DEF

WXY

MNO

CALL

GHI

PRS

ABC

TUV

JKL

123456789

ETD

ID SET RESET

123456789

ETD

ID SET RESET

Hard-wire

from

Gate Opener

Power Supply

from

Opener

Battery

POWER

RELAY

Jumper ON

wireless mode

Jumper OFF

wired mode

HARD-WIRED INSTALLATION

<RXZLOOQHHGWZRSDLUVRIJDXJH$:*VWUDQGHGGLUHFWEXULDOORZYROWDJHZLUHRB509RQHSDLUWRKDUGZLUHWKH

FRPPXQLFDWLRQEHWZHHQWKHNH\SDGDQGWKHJDWHRSHQHUWKHRWKHUWRH[HQGWKHOLIHRIWKHIRXU³&´EDWWHULHV127(7KH

IRXU³&´EDWWHULHVDUHUHTXLUHGIRUUHOLDEOHRSHUDWLRQRIWKHNH\SDG

Step 1:7XUQWKHJDWHRSHQHU¶VSRZHUVZLWFK2))

Step 2: 'HWHUPLQHKRZWKHZLUHVZLOOHQWHUWKHNH\SDGHJIURPWKHEDFNWKURXJKD

KROHGULOOHGLQWKHSRVWUXQQLQJWKHZLUHRQWKHSRVWVXUIDFH'ULOODKROHLQWKHEDFNRI

WKHNH\SDGFRYHUDQGSXOOWKHZLUHLQWRWKHFRYHU7KHQPRXQWWKHFRYHUWRWKHSRVWXVLQJ

WKHVFUHZVSURYLGHG5XQZLUHWKURXJK39&SLSHIURPWKHJURXQGWRNH\SDGDQGIURPWKH

JURXQGWRWKHRSHQHUFRQWUROERDUGWRSURWHFWLWIURPODZQPRZHUVRUJUD]LQJDQLPDOV

Step 3::LUHWKHNH\SDGWRWKHJDWHRSHQHUFRQWUROERDUG6WULS´RIIWKHHQGVRIRQH

SDLURIORZYROWDJHZLUHV$WWDFKWKHZLUHVWRWKHWHUPLQDOEORFNPDUNHG5(/$<RQWKHNH\SDGFRQWUROERDUGDVVKRZQ

7KHQFRQQHFWZLUHWRWKH&<&/(WHUPLQDORQWKHJDWH

RSHQHUFRQWUROERDUGDQGZLUHWRWKH&20WHUPLQDORQ

WKHJDWHRSHQHUFRQWUROERDUG

127(,I\RXKDYHDPRO 1000/2000/SL1000/SL2000

gate openerFRQQHFWZLUHWRWKH:+7DFFHVVRU\

WHUPLQDODQGZLUHWRWKH*51DFFHVVRU\WHUPLQDO

5HIHUWR\RXUJDWHRSHQHULQVWUXFWLRQPDQXDOIRUPRUH

GHWDLOVRQZLULQJWKHJDWHRSHQHUFRQWUROERDUG

Step 4: :LUHWKHNH\SDGWRWKHEDWWHU\6WULS´RII

WKHHQGVRIWKHVHFRQGSDLURIORZYROWDJHZLUHV$WWDFK

WKHZLUHVWRWKHWHUPLQDOEORFNPDUNHG32:(5RQWKH

NH\SDGFRQWUROERDUGDVVKRZQ&RQQHFWWKHRWKHUHQGRI

WKHZLUHVWRWKHRSHQHU¶VEDWWHU\RQHHQGWRWKH326,7,9(

5('WHUPLQDODQGWKHRWKHUWRWKH1(*$7,9(%/$&.

WHUPLQDO

Step 5:&RQQHFWWKHMXPSHUEHWZHHQWKHWZRWHUPLQDOVRQ

WKHNH\SDGFRQWUROERDUG21DVVKRZQ

Step 6:6OLGHWKHNH\SDGLQWRWKHFRYHUDQGORFN

Step 7: 5HSODFHWKHJDWHRSHQHUFRQWUROERDUGFRYHUDQGWXUQ

WKHSRZHUVZLWFK21

Step 8:3URJUDPWKHNH\SDGSDJH

Drill Hole

Troubleshooting

Pressing the keypad CALL button does not ring the base unit:

  &KHFNWKHEDWWHULHVLQWKHNH\SDGDQGUHSODFHWKHPLIQHFHVVDU\

  0DNHVXUHWKHEDVHXQLWLVWXUQHGRQDQGWKHYROXPHLVWXUQHGXS

  7U\PRYLQJWKHNH\SDGDQGWKHEDVHXQLWFORVHUWRHDFKRWKHUQRFORVHUWKDQIW

  3HUIRUP³6\QF´SURFHGXUHEHORZWKLVZLOOUHTXLUHWZRSHRSOH:

 D 2SHQWKHNH\SDGDQGORFDWHWKH³,'6(7´EXWWRQDERYHWKHEDWWHULHV/RFDWHWKH³,'6(7´EXWWRQRQWKHERWWRP

RIWKHEDVHXQLW

 E 0DNHVXUHWKH³DQWHQQDWRDQWHQQD´GLVWDQFHEHWZHHQWKHNH\SDGDQGWKHEDVHXQLWLVDWOHDVWIHHW

 F 3UHVVWKH³,'6(7´EXWWRQRQWKHNH\SDGXQWLO\RXKHDUDEHHSWKHQUHOHDVH

 G 3UHVVWKH³,'6(7´EXWWRQRQWKHEDVHXQLWIRUDSSUR[LPDWHO\VHFRQGVWKHQUHOHDVH<RXZLOOKHDU21(EHHS

IURPWKHEDVHXQLWDQG7:2IURPWKHNH\SDGZKLFKPHDQVWKHNH\SDGDQGEDVHXQLWDUHV\QFKHG

 H 7HVWWKHV\VWHPE\SUHVVLQJWKH&$//EXWWRQRQWKHNH\SDGWRVHHLIWKHEDVHXQLWUHFHLYHVWKHVLJQDO2QFHWKH

V\VWHPLVZRUNLQJ\RXZLOOQHHGWRV\QFDGGLWLRQDOEDVHVWDWLRQVVHHSDJH

The Master Entry Code does not open the gate and the GRANTED light does not turn green.

  &KHFNWKHEDWWHULHVLQWKHNH\SDGDQGUHSODFHWKHPLIQHFHVVDU\

  3URJUDPWKHNH\SDGSDJH

The Master Entry Code does not open the gate and the GRANTED light turns green.

:,5(/(66,QVWDOODWLRQ

  9HULI\WKDW\RXU(QWU\7UDQVPLWWHURSHUDWHVWKHJDWH

  9HULI\WKDWWKH.H\SDG',3VZLWFKHVDUHPDWFKHGWRWKH(QWU\7UDQVPLWWHU',36ZLWFKHVSDJH

  0DNHVXUHWKH-803(5LQWKHNH\SDGLV127LQVWDOOHGSDJH

:,5(',QVWDOODWLRQ

  %HVXUHWKHZLUHVDUHVHFXUHO\FRQQHFWHGWRWKHJDWHRSHQHUFRQWUROERDUGSDJH

  0DNHVXUHWKH-803(5LQWKHNH\SDGLVLQVWDOOHGSDJH

You’ve forgotten the Master Entry Code:

The following will remove all Entry Codes from the keypad and program the Master Code back to factory default.

  3UHVVDQGKROGWKH5(6(7EXWWRQLQWKHNH\SDGIRUWZRVHFRQGV0DVWHU(QWU\&RGHLVQRZ³´

  3URJUDPWKHNH\SDGSDJH

Limited One Year Warranty

*72$FFHVV6\VWHPV//&³*72´JDWHRSHQHUDFFHVVRULHVDUHZDUUDQWHGE\WKHPDQXIDFWXUHUDJDLQVWGHIHFWVLQZRUNPDQVKLSIRUDSHULRGRIRQH\HDUIURPWKH

GDWHRISXUFKDVHSURYLGHGUHFRPPHQGHGLQVWDOODWLRQSURFHGXUHVKDYHEHHQIROORZHG

,QWKHFDVHRISURGXFWIDLOXUHGXHWRGHIHFWLYHPDWHULDORUPDQXIDFWXUHUZRUNPDQVKLSZLWKLQWKHRQH\HDUZDUUDQW\SHULRGWKHDFFHVVRU\ZLOOEHUHSDLUHGRUUHSODFHG

DWWKHPDQXIDFWXUHU¶VRSWLRQDWQRFKDUJHWRWKHFXVWRPHULIUHWXUQHGIUHLJKWSUHSDLGWR*72$FFHVV6\VWHPV//&+DUWV¿HOG5G7DOODKDVVHH)/

IMPORTANT: Call 850/575-4144 or fax 850/575-8950 for a Return Goods Authorization (RGA) number before returning goods to factory. Products received

at the factory without an RGA will not be accepted.

5HSODFHPHQWRUUHSDLUHGSDUWVDUHFRYHUHGE\WKLVZDUUDQW\IRUWKHUHPDLQGHURIWKHRQH\HDU

ZDUUDQW\SHULRGRUVL[PRQWKVZKLFKHYHULVJUHDWHU*72ZLOOSD\WKHVKLSSLQJFKDUJHVHTXDOWR8QLWHG3DUFHO6HUYLFH*5281'UDWHIRUUHWXUQ

WRWKHRZQHURILWHPVUHSDLUHGXQGHUZDUUDQW\

7KHPDQXIDFWXUHUZLOOQRWEHUHVSRQVLEOHIRUDQ\FKDUJHVRUGDPDJHVLQFXUUHGLQWKHUHPRYDORIWKHGHIHFWLYHSDUWVIRUUHSDLURUIRUWKHUHLQVWDOODWLRQRIWKRVHSDUWVDIWHU

UHSDLU7KLVZDUUDQW\VKDOOEHFRQVLGHUHGYRLGLIGDPDJHWRWKHSURGXFWVZDVGXHWRLPSURSHULQVWDOODWLRQRUXVHFRQQHFWLRQWRDQLPSURSHUSRZHUVRXUFHWDPSHULQJ

RULIGDPDJHZDVFDXVHGE\OLJKWQLQJHOHFWULFDOSRZHUVXUJHZLQG¿UHÀRRGLQVHFWVRURWKHUQDWXUDODJHQW

$IWHUWKHRQH\HDUZDUUDQW\SHULRG*72RURQHRILWVDXWKRUL]HGVHUYLFHFHQWHUVZLOOPDNHDQ\QHFHVVDU\UHSDLUVIRUDQRPLQDOIHH&DOO*72DWIRU

PRUHLQIRUPDWLRQ7KLVZDUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWVZKLFKPD\YDU\IURPVWDWHWRVWDWH7KLVZDUUDQW\LVLQOLHXRIDOO

RWKHUZDUUDQWLHVH[SUHVVHGRULPSOLHG127(9HUL¿FDWLRQRIWKHZDUUDQW\SHULRGUHTXLUHVFRSLHVRIUHFHLSWVRURWKHUSURRIRISXUFKDVH3OHDVHUHWDLQWKRVHUHFRUGV

If you have any questions or concerns, please contact our Technical Service Department

Monday thru Friday 8:00 a.m. to 7:00 p.m. (ET) at 1-800-543-1236 or 850-575-4144

GTO Access Systems, LLC • 3121 Hartsﬁeld Road • Tallahassee, Florida 32303

Telephone (850) 575-0176 • Fax (850) 575-8912 • www.gtoinc.com

7KHFRQWHQWVRIDOOPDWHULDODYDLODEOHRQWKLVLQVWDOODWLRQPDQXDODUHFRS\ULJKWHGE\*72$FFHVV6\VWHPV//&³*72´XQOHVVRWKHUZLVHLQGLFDWHG$OOULJKWVDUHUHVHUYHGE\*72DQG

FRQWHQWPD\QRWEHUHSURGXFHGGRZQORDGHGGLVVHPLQDWHGSXEOLVKHGRUWUDQVIHUUHGLQDQ\IRUPRUE\DQ\PHDQVH[FHSWZLWKWKHSULRUZULWWHQSHUPLVVLRQRI*72$Q\UHSULQWLQJRI*72

SXEOLFDWLRQVLVE\SHUPLVVLRQRQO\&RS\ULJKWLQIULQJHPHQWLVDYLRODWLRQRIIHGHUDOODZ*72*723520LJKW\0XOHDUHUHJLVWHUHGWUDGHPDUNVRI*72$FFHVV6\VWHPV//&*72

$FFHVV6\VWHPVLVDWUDGHPDUNRI*72$FFHVV6\VWHPV//&7KHVHPDUNVDUHWKHH[FOXVLYHSURSHUW\RI*72$FFHVV6\VWHPV//&³*72´$OOULJKWVDUHUHVHUYHGE\*72DQGWKHVH

PDUNVPD\QRWEHXVHGLQDQ\IRUPZLWKRXWWKHSULRUZULWWHQSHUPLVVLRQRI*72

C5@4-:E;@41>-:@1::-;>@>-:?95@@1>

Cet équipement doit être installé et utiliséavec une distance minimale de cm entre leradiateur

ISEDC RSS warning

7KLVGHYLF

HFRP SOLHVZLWK,6('&OLFHQFHH[HPSW566VWDQGDUGV2SHUDWLRQLV

VXEMHFWWRWKHIROORZLQJWZRFRQGLWLRQVWKLVGHYLFHP D\QRW FDXVHLQWHUIHUHQFH

DQGWKLVGHYLFHPXVWDFFHSWDQ\LQWH UIHUHQFHLQFOXGLQJLQWHUIHUHQFHWKDWPD\

FDXVHXQGHVLUHGRSHUDWLRQRIWKHGHYLFH 

Le présent appareil est conforme aux CNR d'ISEDC applicables aux appareils radio

exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d'en compromettre le fonctionnement.

ISEDC Radiation Exposure Statement:

7KLVHTXLS PHQWFRPSOLHVZLWK,6('&5)UDGLDWLRQH[SRVXUHOLPLWVVHWIRUWKIRUDQ

XQFRQWUROOHGHQYLURQP HQW7KLVWUDQVPLWWHUPXVWQRWEHFRORFDWHGRU RSHUDWLQJLQ

FRQMXQFWLRQZLWKDQ\RWKHUDQWHQQDRUWUDQVPLWWHU

Rapport d'exposition de la radiation d' ISEDC :

&HWpTXLSHPHQWHVWFR QIRUPHDX[OLP LWHVGH[SRVLWLRQGDWLRQGHUDGLGHO,6('&UI

GpWHUPLQpHVSRXUXQHQYLURQQHP HQWQRQFRQW U{Op&HWpP HWWHXUQHGRLWSDVrWUH 

&RSODFpRXIRQFWLRQQDQWGDQVODFRQMRQFWLRQDYHFDXFXQHDXWUHDQWHQQHRXpPHWWHXU

This equipment should be installed and operated with minimum distance cm between the

radiator& your body.

& votre corps.

’



connected.

ͲͲ

    

    

 %.%*)2+*-/,!..!(!).

&45?1=A5<91:@/;9<851?C5@4>-05-@5;:1D<;?A>18595@??1@2;>@42;>-:A:/;:@>;8810

1:B5>;:91:@ :0 A?1>? 9A?@ 2;88;C @41 ?<1/525/ ;<1>-@5:3 5:?@>A/@5;:? 2;> ?-@5?2E5:3 $

1D<;?A>1/;9<85-:/1&45?@>-:?95@@1>9A?@:;@.1/;8;/-@10;>;<1>-@5:35:/;:6A:/@5;:

Any Changes or modifications not expressly approved by the party responsible for compliance            

could void the user s authority to operate the equipment.

        

This device complies with part 15 of the FCC Rules. Operation is subject to the following two                

conditions: (1) This device may not cause harmful interference, and (2) this device must accept              

any interference received, including interference that may cause undesired operation.

         

Note: This equipment has been tested and found to comply with the limits for a Class B digital                 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable               

protection against harmful interference in a residentia l installation. This equipment generates          

uses and can radiate radio frequency energy and, if not installed and used in accordance with the                

instructions, may cause harmful interference to radio communications. However, there is no           

guarantee that interference will not occur in a particular installation. If this equipment does             

cause harmful interference to radio or television reception, which can be determined by turning             

the equipment off and on, the user is encouraged to try to correct the interference by one or                 

more of the following measu res:    

ͲͲ      Reorient or relocate the receiving antenna.

ͲͲ        Increase the separ a tion between the equipment and receiver.

ͲͲ                 Connect the equipment into an outlet on a circuit different from that to which the receiver is

Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with minimum distance cm between the

radiator& your body.

GTO I6H-LP6110KP, LP6110KP User manual

Related papers

Other documents