2. Baby & children
  3. Baby travel
  4. Strollers
  5. Mountain Buggy
  6. urban / terrain car seat clip

Mountain Buggy urban / terrain car seat clip Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Mountain Buggy urban / terrain car seat clip Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
IMPORTANT - KEEP FOR FUTURE REFERENCE
SCCPis21/4/08gen
WARNING
• CheckyouhavethePegPéregomodel:
primoviaggioCarSeatforthisCarseat
Clip.
• Donotusethisaccessoryonanyother
strollerasitmaybeunsafe.
• DonotusethisCarseatClipuntilyouhave
readandunderstoodtheinstructions!
• Incorrectusecanmeanseriousinjuryor
deathtoaninfant!
• Neverleaveyourchildunattended.
• CheckthatcarseatandCarseatClipare
secureandcannotmoveforward,back,
sidewaysorupwards.
• Makesureinfantisharnessedintothecar
seatusingthecarseatmanufacturer’s
instructions.
• Donotleavebabyincarseat(onoroff
stroller)forlongperiodsoftime.
Pull support wire out of
sunhood joint A. This
operation is child proof
and therefore requires a
degree of force. To assist
in pulling support wire out,
push against stroller frame
with other hand B.
1
1.TemporarilyRemoveSunhood
Repeat step (1) on other
side.
2
Unfasten two middle
fasteners on both sides
of stroller (at B & C) and
peel fabric back, exposing
frame.
2
1
3
2.PartialSeatUnfastening
Single - T1204
Single - U1204
ThisCarseatCliponlytsthePegPéregomodel:
primoviaggio.
These instructions are for the Peg Pérego Carseat Clip
which t the following model strollers only:
SINGLE CarSEat CLIp INStruCtIoNS
A
B
Sunhood Joint
URBAN
TERRAIN
STAGEONE
ALL MODELS
A
ALL MODELS
Loosen the strap beneath
seat at point A.
URBAN
Recline seat slightly.
B
C
Sunhood
Joint
The stroller seat does not need to be removed to t Carseat Clip.
The sunhood wires need to be removed from sunhood joints to allow
Carseat Clip to be tted. These wires are re-attached to stroller once
Carseat Clip has been tted.
pEG pÉrEGo
model:primoviaggio
FittingCarseatCliptoFrame
STAGETWO
FittingCarSeatontoCarseatClip
STAGETHREE
OPENPOSITION CLOSEDPOSITION
WARNING
• Makesureinfantisharnessedintothecarseatusing
thecarseatmanufacturer’sinstructions.
• WhenttingcarseatontoCarseatClip,ALWAYS
KEEPASTEADYINGHANDONCARSEATAND
INFANT.
• CheckCarseatClipislocatedcorrectlyontostroller
frame.Referbacktodiagramstoensurepositioning
ofsnaplocksarecorrect.
• CheckcarseatandCarseatCliparesecureand
cannotmoveforward,back,sidewaysorupwards.
• DonotuseCarseatClipifyouareunabletosecure
carseatorCarseatClip.Inthiscasecontactstore
wherestrollerwaspurchasedordistributorforyour
country,formorehelp.
• IT IS RECOMMENDED THAT YOU PRACTISE
THEFOLLOWINGINSTRUCTIONSWITHOUT
INFANTINCARSEAT.
Place car seat in CarseatClip so that
infant is facing the stroller handle bar.
1
STAGEFOUR
RemovingCarseatClipfromStroller
STAGEFIVE
1
2
Close all Snap Locks down at, making sure you hear the lock “click”-
indicating they are fully locked.
3
PicturedonUrban
Snap Locks
Snap Locks
TheCarseatClipcomesassembledforUrbanmodel.
Open all four Snap Locks by lifting up levers.
Press CarseatClipon to frame so that TOPSnap Locks are directly
above sunhood joints (on both sides).
(i) Using Allen Key supplied, remove Snap Locks at points B (both sides
by rotating screw in an anti-clockwise direction.
(ii) Using Allen Key supplied, fasten removed Snap Locks at points C
(both sides) by rotating screw in a clockwise direction until screw is
tight and Snap Locks are secure.
Before placing Carseat Clip
on stroller frame, the Snap
Locks at points B need to
be removed and placed at
points C (on both sides).
“CLICK”
TERRAIN & URBAN
TERRAIN ONLY
Sunhood
Joint
Sunhood
Joint
URBAN TERRAIN
Re-AttachingSunhoodWires
Push sunhood wires back into sunhood joints (refer Stage One)
1
Remove sunhood wires (refer Stage One).
Open all four Snap Locks by lifting up levers.
Lift Carseat Clip off stroller frame.
Re-attach sunhood wires (refer Stage Three).
Re-attach two middle fasteners on both sides of stroller.
Tighten strap beneath seat (refer Stage One).
1
2
3
4
5
URBAN
6
Ensure the car seat latches have clicked
on to the CarseatClip bars A&B.
Bar C ts into car seat slot.
2
RemovingCarSeatfromCarseatClip
Carseat Clip Bars
Unlock the car seat from the Carseat Clip by pulling the latch handle
and ling car seat upwards.
Latch Handle
C
B
A
Slot
Latches
Allen Key
A
A
B
B
C
C
Snap Locks
/