Northern MONWM3 Installation Instructions Manual

MONWM3

Fully Adjustable

Dual Arm LCD/LED Wall Mount

INSTALLATION & INSTRUCTION MANUAL

Rev.122018

3625 Cincinnati Avenue, Rocklin, CA 95765

♦

855-388-7422

♦

www.northernvideo.com

2

1

ST 5.5x50 (x3)

W-A

concrete anchor

W-B

(x3)

Package M

Package W

M4x14

M-A

(x4) M5x14 (x4)

M-B

D4 washer

M-C

(x4)

D (x4)5 washer

M-D

3mm Allen key (x1)

M-E

NOTE: Read the entire instruction manual before you start installation and assembly.

Component Checklist

WARNING

• Do not b egin the install ation until you ha ve read and unders tood the instruc tions

and warnings contained in this installation shee t. If you have any qu estions

regarding any of the instruction or warning, please contact your lo cal distributo r.

• This mounting bracket was desig ned to be installed and utilized ONLY as

specified in thi s manual. Improper installation of this product may cause damage

or serious injury.

• This product sh ould only be installed by someone

of goo d mechanical abi lity,

with basic building experience s and fully understanding of this m anual.

• Make sure that the supporting surface will safely support the combined load of

the equipment and all attached har dware and compon ents.

• If mou nting to wood wall s tuds, make sure that mounting screws are anchored

into the center of the studs. Use of a stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position

equipment.

• Tighten screws fi rmly, but do not over tighten. Over tightening can damage the

items, greatly reducing their holding power.

• This product in tended for indoor use only. Using this product outdoors could

lead to product failure and person al injury.

IMPORTANT: Ensure that you have received all parts according to the component ch ecklist prior to installing. If

any parts are mis sing or faulty, telephone your local distributor for a replacement.

2

1

ST 5.5x50 (x3)

W-A

concrete anchor

W-B

(x3)

Package M

Package W

M4x14

M-A

(x4) M5x14 (x4)

M-B

D4 washer

M-C

(x4)

D (x4)5 washer

M-D

3mm Allen key (x1)

M-E

NOTE: Read the entire instruction manual before you start installation and assembly.

Component Checklist

WARNING

• Do not b egin the install ation until you ha ve read and unders tood the instruc tions

and warnings contained in this installation shee t. If you have any qu estions

regarding any of the instruction or warning, please contact your lo cal distributo r.

• This mounting bracket was desig ned to be installed and utilized ONLY as

specified in thi s manual. Improper installation of this product may cause damage

or serious injury.

• This product sh ould only be installed by someone

of goo d mechanical abi lity,

with basic building experience s and fully understanding of this m anual.

• Make sure that the supporting surface will safely support the combined load of

the equipment and all attached har dware and compon ents.

• If mou nting to wood wall s tuds, make sure that mounting screws are anchored

into the center of the studs. Use of a stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position

equipment.

• Tighten screws fi rmly, but do not over tighten. Over tightening can damage the

items, greatly reducing their holding power.

• This product in tended for indoor use only. Using this product outdoors could

lead to product failure and person al injury.

IMPORTANT: Ensure that you have received all parts according to the component ch ecklist prior to installing. If

any parts are mis sing or faulty, telephone your local distributor for a replacement.

4

3

1. Disassemble the VESA Plate

2a. Mount on Wood Stud Wall

Screw the wall

mount onto

the wall

X X

√

WARNING

• Make sure that mounting screws are anchored into the center of the studs. Use of a stud finde r

is highly recommended.

• Installers are responsible to provide hardware for other types of mounting situations.

• Installer must verify that the sup porting surface will safely support the combined load of the

equipment and all attached hardware and components.

3

Drill pilot holes

1

2

Find and mark the exact

locati on of mounting holes

2b. Mount on Solid Brick and Concrete Block

X X

√

Screw the wall

mount onto

the wall

• When installing wall mounts on cinder block, verify the actual concrete thickness is at least

1-3/8" (35 mm) fo r usin g the co ncre te anc hors . Do not drill into mortar joints! Be sure to

mount in a solid part of the block, genera lly 1" (25mm) minimum from the side of the block.

It is sugges ted el ectr ic dri ll on sl ow set ting is used to drill the hole instead of a hammer drill

to avoid bre akin g out th e back of the hole when entering a void or cavity.

• Installer must verify that the

supporting surface will safely support the combined load of the

equipmen t and al l atta ched hardware and components.

WARNING

Drill pilot holes

2

1

Mark the exact

locati on of

mounting

holes

W-A

W-B

W-A

ø 4mm

(ø 5/32")

55mm

(2.2")

50mm

(2")

60mm

(2.4")

50mm

(2”)

ø 8mm

(ø 5/16”)

Loosen

4

3

1. Disassemble the VESA Plate

2a. Mount on Wood Stud Wall

Screw the wall

mount onto

the wall

X X

√

WARNING

• Make sure that mounting screws are anchored into the center of the studs. Use of a stud finde r

is highly recommended.

• Installers are responsible to provide hardware for other types of mounting situations.

• Installer must verify that the sup porting surface will safely support the combined load of the

equipment and all attached hardware and components.

3

Drill pilot holes

1

2

Find and mark the exact

locati on of mounting holes

2b. Mount on Solid Brick and Concrete Block

X X

√

Screw the wall

mount onto

the wall

• When installing wall mounts on cinder block, verify the actual concrete thickness is at least

1-3/8" (35 mm) fo r usin g the co ncre te anc hors . Do not drill into mortar joints! Be sure to

mount in a solid part of the block, genera lly 1" (25mm) minimum from the side of the block.

It is sugges ted el ectr ic dri ll on sl ow set ting is used to drill the hole instead of a hammer drill

to avoid bre akin g out th e back of the hole when entering a void or cavity.

• Installer must verify that the

supporting surface will safely support the combined load of the

equipmen t and al l atta ched hardware and components.

WARNING

Drill pilot holes

2

1

Mark the exact

locati on of

mounting

holes

W-A

W-B

W-A

ø 4mm

(ø 5/32")

55mm

(2.2")

50mm

(2")

60mm

(2.4")

50mm

(2”)

ø 8mm

(ø 5/16”)

Loosen

6

5

TV

Ti ghten all screws but do not over tighten.

Screw VESA plate onto the display.

3. Install VESA Plate

M-C

M-D

M-A

M-B

Top of display

4. Install the Display

Slide the head of VESA plate

along VESA plate mount rail

until it snug fits into the VESA

plate mount.Then tighten

screws (just removed) by hand.

wall

5. Cable Management

Connect cables to your display

and run cables through the wire

clip.

Note: Leave slack in cable for

cantilever arm movement.

Tighten by hand

6

5

TV

Ti ghten all screws but do not over tighten.

Screw VESA plate onto the display.

3. Install VESA Plate

M-C

M-D

M-A

M-B

Top of display

4. Install the Display

Slide the head of VESA plate

along VESA plate mount rail

until it snug fits into the VESA

plate mount.Then tighten

screws (just removed) by hand.

wall

5. Cable Management

Connect cables to your display

and run cables through the wire

clip.

Note: Leave slack in cable for

cantilever arm movement.

Tighten by hand

lwal

INSTALLATION INSTRUCTIONS

LCD Wall Mount

LDA03-113

23"

MAX

75x75

100x100

ISSUED: JUN 2012

CAUTION: DO NOT EXCEED MAXIMUM

LISTED WEIGHT CAPACITY. SERIOUS

INJURY OR PROPERTY DAMAGE MAY

OCCUR!

15kg

(33lbs)

MAX

6. Adjustment

It is necessary to slightly loosen or tighten the adjustment screws using a 3mm Allen key according to the

different weight of display.

Adjust to desired location or tilt.

Maintenance

• Check that the bracket is secure and safe to use at regular intervals(at least every three months).

• Please contact your dealer if you have any questions.

180°

+10° -10°

wall

180°

+20°

-20°

7

M-E

MONWM3

Fully Adjustable

Dual Arm LCD/LED Wall Mount

INSTALLATION & INSTRUCTION MANUAL

Rev.090412

Tri-ed / Northern Video Distribution ♦ 3625 Cincinnati Avenue, Rocklin, CA 95765

888-874-3336 ♦ www.northernvideo.com

MONWM3

Fully Adjustable

Dual Arm LCD/LED Wall Mount

INSTALLATION & INSTRUCTION MANUAL

Rev.122018

3625 Cincinnati Avenue, Rocklin, CA 95765

♦

888-874-3336

♦

www.northernvideo.com

Northern MONWM3 Installation Instructions Manual

Northern MONWM3 Installation Instructions Manual

Related papers

Other documents