Ematic EMW222 Installation guide

EMW222
Ematic
Brand
Ematic
Model
EMW222
Category
Flat panel desk mounts
Type
Installation guide

Ematic EMW222 is a folding LCD ceiling mount designed for indoor use, supporting displays up to 37 inches and a maximum weight of 44lbs. It features adjustable tilt and swivel capabilities, allowing you to position your display for optimal viewing angles. The mount is compatible with VESA mounting patterns of 75x75mm, 100x100mm, 200x100mm, and 200x200mm, making it suitable for a wide range of displays. Installation requires basic building experience and should be performed by someone with good mechanical ability.

Ematic EMW222 is a folding LCD ceiling mount designed for indoor use, supporting displays up to 37 inches and a maximum weight of 44lbs. It features adjustable tilt and swivel capabilities, allowing you to position your display for optimal viewing angles. The mount is compatible with VESA mounting patterns of 75x75mm, 100x100mm, 200x100mm, and 200x200mm, making it suitable for a wide range of displays. Installation requires basic building experience and should be performed by someone with good mechanical ability.

INSTALLATION MANUAL
Folding LCD Ceiling Mount
EMW222
ISSUED: MAY. 2013
CAUTION: DO NOT EXCEED
RATED LISTED WEIGHT. SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!
11
20kg
(44lbs)
RATED
20kg
(44lbs)
RATED
37"
MAX
75x75
100x100
200x100
200x200
7. Adjustment
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your distributor if you have any questions.
0°/-90°
For saving the space, you can fold the display by pushing the display back until it fits in place.
Adjust to the desired position.
21
NOTE: Read the entire instruction manual before you start installation and assembly.
Component Checklist
WARNING
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
Package W
concrete anchor (x4)
W-B
ST6.3x55 (x4)
W-A
D6 washer (x2)
W-C
D8 washer (x4)
M-F
D5 washer (x4)
M-E
small spacer (x8)
M-G
M5x14 (x4)
M-B
M6x14 (x4)
M-C
M8x20 (x4)
M-D
M4x14 (x4)
M-A
ceiling mount (x1)
A
4mm Allen key (x1)
B
6mm Allen key (x1)
C
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone with good mechanical ability
who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
1
mark the exact
location of
mounting holes.
3a. For Wooden Ceiling Mounting
ø 4.5mm
(ø 3/16”)
55mm
(2.2")
55mm
2.2"( )
55mm
(2.2”)
Screw the screws
into the ceiling
Drill pilot holes
2
1. Separating the VESA Plate
3
4
Use a proper Allen key to loosen the screws in order to separate the VESA plate from the ceiling mount.
2. Opening the Mount
Press
B
Open the mount for installing.Press the ceiling plate down,then lift it up till fully open.
Loosen
Tighten the screw leaving a
4mm space to ceiling.
W-A
Screw the screws
into the ceiling
Drill pilot holes
1
2
Mark the exact
location of
mounting holes
3b. For Solid Brick and Concrete Mounting
65
WARNING
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
Align the both holes of ceiling plate to the
screws in ceiling and move the ceiling
plate until the both screws are seated in
upper area of tear-drop mounting holes.
Fix the ceiling plate using the two other screws and then tighten all screws.
W-C
W-A
W-B
W-A
Tighten the screw leaving a
4mm space to ceiling.
60mm
(2.4")
60mm
2.4"( )
60mm
(2.4")
ø 10mm
(ø 3/8")
87
4. Installing the VESA Plate
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING
Align the both holes of ceiling plate to the
screws in ceiling and move the ceiling
plate until the both screws are seated in
upper area of tear-drop mounting holes.
W-C
W-A
Fix the ceiling plate using the two other screws and then tighten all screws.
M-A
M-B
M-C
M-D
M-E
M-F
or
Tighten all screws but do not over tighten.
• Screw the VESA plate onto the display.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
TV
TV
TV
TV
M-D
M-F
M-G
M-F
M-G
M-G
M-D
Top of the display
109
5. Hooking the Display onto the Ceiling Mount
Hang the display with the VESA
plate onto the ceiling mount.
6. Adjustment
C
Height
adjustable
Install the screws to fix the ceiling mount
and VESA plate together tightly.
Loosen screws(but not remove) and adjust the display to desired height as needed, then tighten screws.
It is necessary that slightly
loosen or tighten adjustment
screws to adjust tension
using a proper Allen key.
Remove the decorative
covers for adjusting
tension.
B
B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Ematic EMW222 Installation guide

EMW222
Ematic
Brand
Ematic
Model
EMW222
Category
Flat panel desk mounts
Type
Installation guide

Ematic EMW222 is a folding LCD ceiling mount designed for indoor use, supporting displays up to 37 inches and a maximum weight of 44lbs. It features adjustable tilt and swivel capabilities, allowing you to position your display for optimal viewing angles. The mount is compatible with VESA mounting patterns of 75x75mm, 100x100mm, 200x100mm, and 200x200mm, making it suitable for a wide range of displays. Installation requires basic building experience and should be performed by someone with good mechanical ability.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents