Toro CM-658H-S Concrete Mixer User manual

CM-658H-S Concrete Mixer
Toro
Brand
Toro
Model
CM-658H-S Concrete Mixer
Type
User manual

This manual is also suitable for

FormNo.3421-311RevA
CM-658H-SConcreteMixer
ModelNo.68004C—SerialNo.402000000andUp
ModelNo.68006C—SerialNo.402000000andUp
ModelNo.68007C—SerialNo.402000000andUp
Registeratwww.Toro.com.
OriginalInstructions(EN)
*3421-311*A
ItisaviolationofCaliforniaPublicResourceCode
Section4442or4443touseoroperatetheengineon
anyforest-covered,brush-covered,orgrass-covered
landunlesstheengineisequippedwithaspark
arrester,asdenedinSection4442,maintainedin
effectiveworkingorderortheengineisconstructed,
equipped,andmaintainedforthepreventionofre.
Theenclosedengineowner'smanualissupplied
forinformationregardingtheUSEnvironmental
ProtectionAgency(EPA)andtheCaliforniaEmission
ControlRegulationofemissionsystems,maintenance,
andwarranty.Replacementsmaybeorderedthrough
theenginemanufacturer.
TireInformation—TheDOTtireinformationislocated
onthesideofeachtire.Thisinformationgivesload
andspeedratings.Replacementtiresshouldhavethe
sameorbetterratings;refertoSpecications(page
15)toensurethatthetiresonyourmachinemeetor
exceedtheweightrequirementsofyourmachine.
WARNING
CALIFORNIA
Proposition65Warning
Theengineexhaustfromthisproduct
containschemicalsknowntotheStateof
Californiatocausecancer,birthdefects,
orotherreproductiveharm.
Useofthisproductmaycauseexposure
tochemicalsknowntotheStateof
Californiatocausecancer,birthdefects,
orotherreproductiveharm.
Introduction
Thismachineisdesignedtomixconcrete,plaster,
reproongmaterial,grout,andothersmall-grained
concreteproducts.Youcantowthemachinebehinda
vehicleequippedwithahitchappropriateforthetype
oftowpoleyourmachinehas(ball,pintle,orpinhitch).
Readthisinformationcarefullytolearnhowtooperate
andmaintainyourproductproperlyandtoavoid
injuryandproductdamage.Youareresponsiblefor
operatingtheproductproperlyandsafely.
YoumaycontactT orodirectlyatwww.Toro.com
forproductsafetyandoperationtrainingmaterials,
accessoryinformation,helpndingadealer,orto
registeryourproduct.
Wheneveryouneedservice,genuineToroparts,or
additionalinformation,contactanAuthorizedService
DealerorT oroCustomerServiceandhavethemodel
andserialnumbersofyourproductready.Figure1
andFigure2identifythelocationofthemodeland
serialnumbersontheproduct.Writethenumbersin
thespaceprovided.
Important:Withyourmobiledevice,youcan
scantheQRcodeontheserialnumberdecal(if
equipped)toaccesswarranty,parts,andother
productinformation.
g241810
Figure1
Models68004Cand68006C
1.Modelandserialnumberlocation
g241813
Figure2
Models68007C
1.Modelandserialnumberlocation
©2018—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
2
Contactusatwww.Toro.com.
PrintedintheUSA
AllRightsReserved
ModelNo.
SerialNo.
Thismanualidentiespotentialhazardsandhas
safetymessagesidentiedbythesafety-alertsymbol
(Figure3),whichsignalsahazardthatmaycause
seriousinjuryordeathifyoudonotfollowthe
recommendedprecautions.
g000502
Figure3
Safety-alertsymbol
Thismanualuses2wordstohighlightinformation.
Importantcallsattentiontospecialmechanical
informationandNoteemphasizesgeneralinformation
worthyofspecialattention.
Contents
Safety.......................................................................4
SafeOperatingPractices....................................4
SafetyandInstructionalDecals..........................7
Setup......................................................................10
1InstallingtheT owPole...................................10
2InstallingtheT ongue......................................10
3InstallingtheSafetyChain...............................11
ProductOverview...................................................12
Controls...........................................................13
EngineControls............................................13
Specications..................................................15
Attachments/Accessories.................................15
Operation................................................................15
TowingtheMachine..........................................16
PreparingtoUsetheMachine...........................21
LoweringtheStabilizerLegs.............................21
OpeningandClosingtheCowl..........................22
AddingFuel......................................................22
PerformingDailyMaintenance..........................24
StartingtheEngine...........................................24
ShuttingOfftheEngine.....................................25
MixingtheMaterial...........................................25
DumpingtheMaterial........................................26
CleaningtheDrum............................................27
Maintenance...........................................................28
RecommendedMaintenanceSchedule(s)...........28
Pre-MaintenanceProcedures..............................28
PreparingtheMachineforMaintenance............28
DisconnectingtheSpark-PlugWire..................29
RemovingtheDividerPlate..............................29
InstallingtheDividerPlate................................29
Lubrication..........................................................30
LubricatingtheMachine....................................30
EngineMaintenance...........................................30
ServicingtheAirCleaner..................................30
ServicingtheEngineOil....................................31
ServicingtheSparkPlug...................................33
CleaningtheSparkArrester..............................34
DriveSystemMaintenance..................................35
TireAirPressure...............................................35
InspectingtheTires..........................................35
TorquingtheWheelLugNuts............................36
BeltMaintenance................................................36
CheckingtheDrive-BeltTension.......................36
AdjustingtheDrive-beltTension........................37
ReplacingtheDriveBelts..................................37
ReplacingtheLightBulbs.....................................38
ReplacingtheRear-facingSideBulbs...............38
ReplacingtheSide-facingBulbs.......................38
ReplacingtheCenterBulbs..............................39
Cleaning..............................................................39
CleaningtheMachine.......................................39
Storage...................................................................40
Troubleshooting......................................................41
3
Safety
Improperuseormaintenancebytheoperatoror
ownercanresultininjury.T oreducethepotential
forinjury,complywiththesesafetyinstructions
andalwayspayattentiontothesafety-alertsymbol
(Figure3),whichmeans:Caution,Warning,or
Danger—personalsafetyinstruction.Failureto
complywiththeinstructionmayresultinpersonal
injuryordeath.
SafeOperatingPractices
Thisproductiscapableofamputatinghands.Always
followallsafetyinstructionstoavoidseriousinjuryor
death.
WARNING
Machiningorhandlingstone,masonry,
concrete,metal,andothermaterialscan
generatedust,mists,andfumescontaining
chemicals,suchassilica,knowntocause
seriousorfatalinjuryorillness,suchas
respiratorydisease,silicosis,cancer,birth
defects,orotherreproductiveharm.
•Controldust,mist,andfumesatthe
sourcewherepossible.Usewaterfordust
suppressionwheneverpossible.
•Usegoodworkpracticesandfollowthe
recommendationsofthemanufactureror
suppliers,OSHA,andotheroccupational
andtradeassociations.
•Alwaysfollowrespiratoryprecautions.
•Whenyoucannoteliminatethehazards
frominhalation,youandallbystanders
shouldweararespiratorapprovedby
OSHAforthematerialthatyouare
handling.
WARNING
Engineexhaustcontainscarbonmonoxide,
whichislethalifinhaled.
Donotruntheengineindoorsorinan
enclosedarea.
Training
•Parkthemachineonalevelsurface,shutoffthe
engine,waitforallmovingpartstostop,andallow
themachinetocoolbeforeadjusting,cleaning,
storing,orrepairingthemachine.
•Readandunderstandthecontentsofthis
Operator’sManualbeforeyoustarttheengine.
Ensurethateveryoneusingthisproductknows
howtouseitandunderstandsthewarnings.
•Becomefamiliarwiththesafeoperationofthe
equipment,operatorcontrols,andsafetysigns.
•Alloperatorsandmechanicsshouldbetrained.
Theownerisresponsiblefortrainingthem.
•Neverletchildrenoruntrainedpeopleoperateor
servicetheequipment.Localregulationsmay
restricttheageoftheoperator.
•Theowner/usercanpreventandisresponsible
foraccidentsorinjuriestopeopleordamageto
property.
Towing
•Checkwithyourlocalcountyorstatetowingsafety
regulationsbeforetowingthemachine.
•Toreducethepossibilityofanaccidentwhile
transportingthemachineonpublicroads,ensure
thatthetowingvehicleismechanicallysoundand
ingoodoperatingcondition.
•Shutofftheengineandturnthefuelvalvetothe
offpositionbeforetransportingthemachine.
•Whentowingwithaballhitch,ensurethatitisthe
propersizeforthehitchcoupleronthemachine.
•Whentowingwithapintlehitch,ensurethatthe
eyeofthetowpoleisthecorrectdimensionfor
thepintlehook.
•Inspectthehitchandcouplingforwear.Donot
towthemachinewithdamagedorwornhitches,
couplings,chains,orothercomponents.
•Checktheairpressureofthetiresonthetowing
vehicleandadjustthepressureasneeded.
•Checkthetiretreadandsidewallfordamageand
wearandreplacethetireifnecessary.
•Properlyattachthesafetychainstothetowing
vehiclebycrossingthechainsandremovingany
extraslack.
•Ensurethatthedirectionalandbrakelightsare
workingproperly(ifequipped).
•Ensurethatthedirectional,backup,andbrake
lightsofthetowvehicleareworkingproperly(if
equipped).
•Beforetowing,ensurethatyourmachineis
correctlyandsecurelyattachedtothetowing
vehicle.
•Ensurethatthesafetychainsareproperlysecured
tothevehicle,andleaveenoughslackforturning.
4
•Donotcarryanymaterialinthemachinewhen
towing.
•Avoidsuddenstopsandstarts.Thiscancause
skiddingorjackkning.Smooth,gradualstartsand
stopsimprovestowing.
•Avoidsharpturnstopreventrolling.Towonlywith
avehiclethathasahitchdesignedfortowing.Do
notattachtowedequipmentexceptatthehitch
point.
•Donottowthemachinefasterthan88km/h(55
mph).
•Usecautionwhenbackingup;useaspotter
outsidethevehicletoguideyou.
•Donotallowanyonetositorrideonthemachine.
•Disconnectthemachinefromthetowvehicle
beforeusingit.
•Placechocksunderneaththetirestopreventthem
fromrollingwhilethemachineisparked.
Preparation
Becomefamiliarwiththesafeoperationofthe
equipment,operatorcontrols,andsafetysigns.
•Useonlyaccessoriesandattachmentsapproved
bythemanufacturer.
•Wearpersonalprotectiveequipmentand
appropriateclothingincluding:
–Hardhat
–Respiratorordustmask
–Faceshield
–Safetyglasses
–Hearingprotection
–Safetyshoes
–Longpants
–Shirtwithlongsleevesthataretightatthe
wrists
–Tight-ttinggloveswithoutdrawstringsorloose
cuffs
•Wearappropriateclothing,includingeye
protection;longpants;substantial,slip-resistant
footwear;andhearingprotection.Tiebacklong
hairanddonotwearloosejewelry.
•Ensurethatthemachineisonalevelsurface
beforeoperatingit.
•Chockthetiresofthemachinetoprevent
unintendedmovement.
•Beforeeveryuse,dothefollowing:
–Inspectthecoupler,ball,andhitch.
–Ensurethatalllightsarefunctioningproperly
(ifequipped).
–Ensurethatthetiresareproperlyinated.
–Ensurethatthelugnutsaretightandtorqued
properly.
–Ensurethatthemachineisproperlysecured.
FuelSafety
•Useextremecareinhandlingfuel.Itisammable
anditsvaporsareexplosive.
•Extinguishallcigarettes,cigars,pipes,andother
sourcesofignition.
•Useonlyanapprovedfuelcontainer.
•Donotremovethefuelcaporllthefueltank
whiletheengineisrunningorhot.
•Donotaddordrainfuelinanenclosedspace.
•Donotstorethemachineorfuelcontainerwhere
thereisanopename,spark,orpilotlight,such
asonawaterheaterorotherappliance.
•Ifyouspillfuel,donotattempttostarttheengine;
avoidcreatinganysourceofignitionuntilthefuel
vaporshavedissipated.
Operation
•Useyourfullattentionwhileoperatingthe
machine.Donotengageinanyactivitythat
causesdistractions;otherwise,injuryorproperty
damagemayoccur.
•Donotrunanengineinanenclosedorpoorly
ventilatedarea.
•Operatethemachineonlyingoodlighting
conditions.
•Beforestartingthemachine,ensurethatthereare
nopeopleorobstaclesnearorunderthemachine.
•Shutofftheenginebeforeleavingthemachinefor
anyreason.
Neverleavearunningmachineunattended.
Alwaysshutofftheengineandverifythatall
movingpartshavestopped.
•Chockthetiresofthemachineorkeepitattached
tothetowingvehiclewhenitisnotinuse.
•Keepyourhandsawayfromanymovingparts.
Keepyourfeetawayfromthetiresandthefront
post.
•Donotoperatethemachineundertheinuence
ofalcoholordrugs.
•Donotplaceyourhandsoranysolidobjectinto
thedrumwhenthemachineisinoperation.
•Donottouchpartsthatmaybehotfromoperation.
Allowthemtocoolbeforeattemptingtomaintain,
adjust,orservicethemachine.
•Nevermovethemachinewhiletheengineis
running.
•Keepthecowlclosedandlatchedduringoperation.
5
•Ensurethatalltheguardsandshieldsaresecurely
inplacebeforeoperatingthemachine.
•Ifthemixingpaddlesstrikeanobjectorifthe
machinestartsmakinganunusualnoiseor
vibration,shutofftheengine,waitforallmoving
partstostop,andemptythedrum.Inspectfor
cloggingordamage.Clean,repair,and/orreplace
anydamagedparts.
•Donotchangetheenginegovernorsettingor
overspeedtheengine.
•Donotoperatethemachinewhenthereistherisk
oflightning.
MaintenanceandStorage
•Beforeperformingmaintenance,dothefollowing:
–Parkthemachineonalevelsurface.
–Shutofftheengine,disconnectthespark-plug
wire,andwaitforallmovementtostopbefore
adjusting,cleaning,orrepairingthemachine.
–Lettheenginecoolbeforeperforming
maintenanceorstoringthemachine.
–Disengageallpowerandoperationcontrols.
•Neverlubricate,service,repair,oradjustthe
machinewiththeenginerunning.
•Keepequipmentmaterialsclearfromthemufer
andenginetopreventres.Cleanupoilorfuel
spills.
•Neverallowuntrainedpersonneltoservicethe
machine.
•Keepyourhands,feet,andclothingawayfrom
movingparts.Ifpossible,donotmakeadjustments
withtheenginerunning.
•Keepallpartsingoodworkingconditionandall
fastenerstightened.Replaceallwornordamaged
decals.
•Removeanybuildupofgrease,oil,ordebrisfrom
themachine.
•Shutofftheengineandinspectthemachineif
anobjectentersthedrumorcausesanother
obstruction.Makeallnecessaryrepairsbefore
startingthemachine.
•Donottamperwithsafetydevices.
•Chockthetireswhenstoringthemachine.
•Keepallfastenersandhoseclampssecurely
tightenedandallequipmentingoodcondition.
•UseonlygenuineT ororeplacementparts.
6
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea
ofpotentialdanger.Replaceanydecalthatisdamagedormissing.
decal125-4939
125-4939
1.Warning—readthe
Operator’sManual.
4.Toxicgasinhalation
hazard—Donotrunthe
engineinanenclosed
space.
2.Handandarm
entanglementatthe
beltdrive;crushinghazard
ofhand;entanglement
hazardofhandatthe
shaft—keepyourhands
awayfrommovingparts;
keepallguardsand
shieldsinplace.
5.Explosionhazard—shut
offtheengineandkeep
awayfromameswhen
refueling.
3.Entanglementhazard
atpaddles—shutoff
theengineandwait
forallmovingpartsto
stopbeforeperforming
maintenance.
decal125-4940
125-4940
1.Warning
3.Engine—shutoff
2.Engine—run
decal125-8175
125-8175
1.ReadtheOperator’sManualforinformationongreasing
themachine.
7
decal125-8216
125-8216
1.ReadtheOperator’s
Manualforinformationon
howtotowthemachine.
2.Warning—limittowing
speedtolessthan88km/h
(55mph).
decal130-8322
130-8322
1.Useonlyfuelwithan
alcoholcontentbyvolume
under10%.
3.Donotusefuelwithan
alcoholcontentbyvolume
greaterthan10%.
2.ReadtheOperator's
Manualformore
informationonfuel.
decal132-4041
132-4041
1.ReadtheOperator'sManualformoreinformationonservicingthemachine.
8
decal132-4042
132-4042
1.ReadtheOperator'sManualformoreinformationonservicingthemachine.
decal133-5619
133-5619
9
Setup
1
InstallingtheTowPole
Side-DumpModelsOnly
Partsneededforthisprocedure:
1
Towpolekit(soldseparately)
TowPoleSpecications
Purchasethetowpolekit(includingfasteners)that
meetsyourneedsfromyourAuthorizedService
Dealer.Themachinehasthefollowingtowpole
options:
HitchTypeLength
50mm(2inch)ball—stamped78.7cm(31inches)or127cm
(50inches)
50mm(2inch)ball—forged78.7cm(31inches)or127cm
(50inches)
Pintle
78.7cm(31inches)or127cm
(50inches)
InstallingtheTowPole
1.Removetheboltandnutfromthetowpole
(Figure4).
g019804
Figure4
1.Towpole4.Bolthole
2.Frontpost
5.Frametting
3.Bolt6.Nut
2.Slidethetowpoleforwardandaligntheholein
thepolewiththeholeintheframetting(Figure
4).
3.Inserttheboltthroughtheholesinthettingand
thepole(Figure4).
4.Threadthenutontotheboltandtightenthem
untiltheyaretightagainsttheframetting
(Figure4).
Note:Iftheself-lockingnyloninsertinthe
locknutwearswithuse,replacethenutwitha
newGrade5orGrade8locknut.
2
InstallingtheTongue
End-DumpModelsOnly
Partsneededforthisprocedure:
1Tongue
1Frontstabilizerleg
6
Shortbolt
1Longbolt
7
Nut
Procedure
1.Lowertherearstabilizerlegs;refertoLowering
theStabilizerLegs(page21).
2.Placejackstandsunderthefrontframerail
topreventthemachinefromtippingforward
(Figure5).
WARNING
Mechanicalorhydraulicjacksmayfailto
supportthemachineandcauseserious
injury.
Usejackstandswhensupportingthe
machine.
10
g021091
Figure5
1.Supportpoints
3.Removethe2nutsandboltsthatsecurethe
frontstabilizerlegtotheframe(Figure6)and
removethefrontstabilizerleg.
g021092
Figure6
1.Frontstabilizerleg
4.Installthetongueintotheopeningatthefront
ofthemachineandsecureitwith6nutsand
shortboltstorquedto102N∙m(75ft-lb);refer
toFigure7.
g021093
Figure7
1.Clevispin
4.Nut
2.Longbolt5.Tongue
3.Shortbolt
6.Frontstabilizerleg
5.Alignthetoprearholeinthefrontstabilizerleg
totheholepastthehandleinthefrontofthe
tongue(Figure7).
6.Installthelongboltthroughtheholesandsecure
itwithanuttorquedto102N∙m(75ft-lb);refer
toFigure7.
Note:Thestabilizerlegpivotsrearwardonthe
bolt.Ifyouinstalltheboltintothewronghole,
thestabilizerlegwillnotworkproperly.
7.Inserttheclevispintolockthefrontstabilizerleg
inposition(Figure7).
3
InstallingtheSafetyChain
Partsneededforthisprocedure:
1
Safetychain
2
Connectinglink
Procedure
Formahookontheendofabendablepieceofrodor
stiffwire(notincluded)andinstallthesafetychainand
connectinglinksasshowninFigure8orFigure9.
g035100
Figure8
Side-DumpModels
11
g035474
Figure9
End-DumpModels
Note:Ensurethatapproximatelyequallengthsof
safetychainextendfromeithersideofthefrontpost.
ProductOverview
g020832
Figure10
Models68004C,68006C,and68009C
1.Enginecowl6.Towpole
2.Engineswitch
7.Safety-chainkeyholes
3.Drum8.Drum-tiltbrake
4.Handwheel9.Rubberlatch
5.Lightingwireharness
10.Trailerlight(2)
12
g020833
Figure11
Models68007Cand68008C
1.Tongue-mountedtow
coupler
8.Drum-tiltbrake
2.Safety-chainkeyholes9.Clevispin
3.Rubberlatch10.Rearstabilizerlegs
4.Engineswitch
11.Trailerlight(2)
5.Enginecowl12.Rearwardpinhole
6.Drum13.Frontstabilizerleg
7.Handwheel14.Lightingwireharness
Controls
Becomefamiliarwithallthecontrolsbeforeyoustart
theengineandoperatethemachine.
EngineSwitch
WhentheengineswitchonthecowlisintheRUN
position,itallowstheenginetorun.Movingtheengine
switchtotheSTOPpositionshutsofftheengine.
EngineControls
g019744
Figure12
1.Recoil-starthandle5.Fuelcap
2.Fuelvalve
6.Oildipstick
3.Chokelever7.Oil-drainplug
4.Throttlelever
8.On/Offswitch
FuelValve
Thefuelvalve(Figure13)islocatedunderneaththe
chokelever.Movetheleverforthefuelvalvetothe
ONpositionbeforeattemptingtostarttheengine.
Whenyouhavenishedmixing,shutofftheengine
andmovethefuel-valvelevertotheOFFposition.
13
g018792
Figure13
1.Fuelvalve3.Throttlelever
2.Chokelever
ChokeLever
Usethechokelever(Figure13)tostartacoldengine.
Beforepullingtherecoil-starthandle,movethechoke
levertotheCLOSEDposition.Oncetheengineis
running,movethechokelevertotheOPENposition.
Donotusethechokeiftheengineisalreadywarmed
uporiftheairtemperatureishigh.
ThrottleLever
Thethrottlelever(Figure13)controlsthespeed(rpm)
oftheengine.Itislocatednexttothechokelever.It
setstheenginespeedandthereforecanincreaseand
decreasetherotationspeedofthemixingpaddles.
Forbestperformance,setthiscontroltotheFAST
positionwhenmixingmaterial.
EngineOn/OffSwitch
TheOn/Offswitchislocatedonthefrontoftheengine.
•RotateittotheONpositiontostartandrunthe
engine.
•RotateittotheOFFpositiontoshutofftheengine.
g021103
Figure14
1.OFFposition2.ONposition
Recoil-StartHandle
Tostarttheengine,pulltherecoil-starthandle(Figure
12)quicklytoturntheengineover.Theengine
controlsdescribedabovemustallbesetcorrectlyfor
theenginetostart.
Oil-LevelSwitch
Theoil-levelswitchislocatedinsidetheengine,andit
doesnotallowtheenginetorunwhentheoillevelis
belowthesafeoperatinglimit.
Handwheel
Thehandwheelcontrolsthetiltofthedrum.
Drum-tiltBrake
Thedrum-tiltbrakelocksthedrumintoanupright
positionoradischargingposition.
14
Specications
Note:Specicationsanddesignaresubjecttochangewithoutnotice.
Model6800468006680076800868009
BatchCapacity
0.17m
3
(6.0ft
3
)
0.255m
3
(9.0ft
3
)
0.255m
3
(9.0ft
3
)
0.255m
3
(9.0ft
3
)
0.255m
3
(9.0ft
3
)
TotalVolume0.255m
3
(9.0ft
3
)
0.43m
3
(15.1ft
3
)
0.43m
3
(15.1ft
3
)
0.43m
3
(15.1ft
3
)
0.43m
3
(15.1ft
3
)
DrumMaterial
SteelSteelSteel
PolyethylenePolyethylene
Length198cm
(78inches)
213cm
(84inches)
216cm
(85inches)
216cm
(85inches)
213cm
(84inches)
Width117cm
(46inches)
142cm
(56inches)
216cm
(85inches)
216cm
(85inches)
142cm
(56inches)
Height147cm
(58inches)
165cm
(65inches)
180cm
(71inches)
180cm
(71inches)
165cm
(65inches)
Weight313kg
(690lb)
363kg
(800lb)
397kg
(875lb)
397kg
(875lb)
381kg
(837lb)
Attachments/Accessories
AselectionofT oroapprovedattachmentsand
accessoriesisavailableforusewiththemachine
toenhanceandexpanditscapabilities.Contact
yourAuthorizedServiceDealerorauthorizedT oro
distributororgotowww.T oro.comforalistofall
approvedattachmentsandaccessories.
Toensureoptimumperformanceandcontinuedsafety
certicationofthemachine,useonlygenuineToro
replacementpartsandaccessories.Replacement
partsandaccessoriesmadebyothermanufacturers
couldbedangerous,andsuchusecouldvoidthe
productwarranty.
Operation
Important:Beforeoperating,checkthefueland
oillevels,andremovedebrisfromthemachine.
Ensurethattheareaisclearofpeople.
CAUTION
Thismachineproducessoundlevelsthatcan
causehearinglossthroughextendedperiods
ofexposure.
Wearhearingprotectionwhenoperatingthis
machine.
g232186
Figure15
1.Wearhearingprotection.
15
TowingtheMachine
Beforetowingthemachine,readalltheinformation
andperformalltheapplicableprocedurestointhis
sectiontoensuresafeandpropertowing.
WARNING
Towingthemachineathighspeedincreases
theriskofahitchmalfunctionandtirefailure.
Higherspeedsalsoincreasethemomentum
ofthemachineandbrakingdistance.Ifthe
machinedetachesfromthetowvehicleathigh
speed,itcouldcausedamagetoproperty,or
injuryordeathtobystanders.
Donotexceed88km/h(55mph)whentowing
themachine.Forpoorroadconditionsor
inclementweather,reducespeedaccordingly.
WARNING
Towingthemachinewithmaterialinthedrum
increasestheriskofahitchmalfunctionand
tirefailure.Inaddition,materialcouldbounce
outofthedrumandhitothervehiclesand/or
people.Materialinthedrumincreasesthe
weight,whichaffectsmomentumandbraking
distance.
Donottowthemachinewithmaterialinthe
drum.
•ReviewandunderstandtheSafeOperating
Practices(page4).
•Testthebrakesofthetowvehiclebeforetowing.
•Avoidsuddenstartsandstopswhiletowingthe
machine.
TowVehicleRequirements
Beforeconnectingthemachinetoyourtowvehicle,
ensurethatyourvehicleispreparedasfollows:
•Ensurethatyourtowvehiclehastowing
capacityfortheweightofthemachine;referto
Specications(page15).
•UseaClass2orlargerreceiver.
•Ensurethatyourtowvehiclehastheappropriate
hitchtotowthemachine;optionsincludea50mm
(2inch)ballhitchorapintlehitch.
•Ifthemachineisequippedwithatrailer-lightkit,
ensurethattheelectricalconnectorofthetow
vehicleiscompatiblewiththeelectricalconnector
ofthemachine.Themachineusesastandard
4-pin,atplug.Ifyourtowvehiclehasadifferent
typeofplug,obtainanadapterfromanautomotive
partsstorebeforetowing.
PreparingtheMachineforTowing
1.Shut-offtheengineandfuelvalve.
2.Emptythedrum.
3.Usingthehandwheel,positionthedrumsothatit
ispointingdowntowardtheground(Figure16).
g019806
Figure16
1.Drumpointingdown3.Towpoleboltedinplace
2.Drum-tiltbrakeengaged
4.Lockthedrumintopositionbypushingdownthe
drum-tilt-brakehandle(Figure17).
g019733
Figure17
Drum-TiltBrake
1.Unlockedposition2.Lockedposition
5.Closetheenginecowlandsecurethecowl
latches(Figure18).
16
g019741
Figure18
6.Inspectthetires;refertoInspectingtheTires
(page35).
RaisingtheStabilizerLegs
End-DumpModelsOnly
End-dumpmodelshaveafrontstabilizerlegand2
rearstabilizerlegs.
Raisethestabilizerlegsbeforetowingthemachine.
1.Adjustthemachinesothatthereisnoweight
restingontherearstabilizerlegs.
2.Pulltheclevispinoutfrom1oftherearstabilizer
legsandthebracket(Figure19).
g019917
Figure19
3.Slidethestabilizerlegupinthebracketand
alignthepinholeofthebracketwiththelower
holeinthestabilizerleg(Figure19).
4.Pushtheclevispinthroughtheholeinthe
bracketandthestabilizerleg(Figure19).
5.Repeatsteps1through4fortheotherrear
stabilizerleg.
6.Liftupwardonthetonguesothatthereisno
weightrestingonthefrontstabilizerleg.
7.Pulltheclevispinoutfromthefrontstabilizerleg
andthetongue(Figure20).
g019915
Figure20
1.Removetheclevispin.3.Installtheclevispin.
2.Rotatethestabilizerleg
up.
8.Rotatethefrontstabilizerlegupintothetongue
(Figure20).
9.Pushtheclevispinthroughtherearwardholein
thetongueandthefrontstabilizerleg(Figure
20).
17
HitchingtheMachinetoaTow
Vehicle
Yourmachineisequippedwith1ofthefollowing
hitchtypes;hitchitasdescribedintheappropriate
procedure:
•Stamped-ballcoupler—HitchingaStamped-Ball
Coupler(page18)
•Forged-ballcoupler—HitchingaForged-Ball
Coupler(page18)
•Pintle-hitchcoupler—HitchingaPintle-Hitch
Coupler(page19)
•Pin-hitchcoupler—HitchingaPin-HitchCoupler
(page19)
HitchingaStamped-BallCoupler
1.Applychassisgreasetothesocketofthecoupler
andtheareaoftheclampthatcontactstheball.
2.Oilthepivotpointsandslidingsurfacesofthe
couplerwithSAE30engineoil.
3.HitchthemachineasshowninFigure21.
g035113
Figure21
HitchingaForged-BallCoupler
1.Applyremovablethread-lockingcompoundto
thethreadsofthecouplerbolttopreventthe
couplerhandlefromcomingloose.
Important:Applythread-lockingcompound
asneededinthefuture.
2.Applychassisgreasetothesocketofthecoupler
andtheareaoftheclampthatcontactstheball.
3.HitchthemachineasshowninFigure22.
18
g035115
Figure22
Note:Useawrenchtokeeptheboltfrom
spinning.
HitchingaPintle-HitchCoupler
g035164
Figure23
HitchingaPin-HitchCoupler
g035116
Figure24
Note:Usea19mm(3/4inch)or22mm(7/8inch)
hitchpin.
ConnectingtheSafetyChainsto
theTowVehicle
1.Pullthesafetychainthroughtheslotsinthe
keyholes,sothatthelengthsoneachsideare
equal.
2.Crossbothlengthsofchainunderthetow
pole(underthetongueforend-dumpmodels).
Forside-dumpmodels,refertoFigure25.For
end-dumpmodels,refertoFigure26.
Note:Crossingthechainsdecreasesthe
chancesofthefrontofthemachinedropping
tothegroundifthehitchdoesnotholdthe
connection.
19
g021177
Figure25
Side-DumpModels
1.Connectinglinks3.Chaincrossedundertow
pole
2.Keyholesinfrontpost
g019928
Figure26
End-DumpModels
1.Connectinglinks3.Chaincrossedunder
tongue
2.Keyholes
4.Chain
3.Connecteachlengthofchaintothesafety
chainmountingpointonthetowvehiclewiththe
connectinglinks(Figure27).
Important:Ensurethatthechainhas
enoughslackforturningaroundcorners
whentowingthemachine.
Note:Forside-dumpmodels,stowtheexcess
chaininsidethebottomofthefrontpostby
pushingitintothekeyholesandlatchingthe
appropriatelinksintothekeyholeslots.
Note:Forend-dumpmodels,connectthe
connectinglinkstotheappropriatelinksinthe
safetychain(Figure27).Iftheexcesschain
hangstoolowandtouchestheground,connect
itagaintotheconnectinglinktoraiseitaway
fromtheground.
g019927
Figure27
1.Connectinglink3.Chainlink
2.Safetychainmounting
pointontowvehicle
4.Chain
ConnectingandCheckingthe
Lights
MachinesEquippedwithaLightKitOnly
1.Connecttheelectricalplugofthemachinewith
theelectricalplugofthetowvehicle(Figure28).
g020828
Figure28
Note:Themachineusesastandard4-pin,at
plug.Ifyourtowvehiclehasadifferenttype
ofplug,obtainanadapterfromanautomotive
partsstorebeforetowing.
2.EnsurethatthetowvehicleisintheNEUTRAL
position,engagetheparkingbrake,andstart
theengine.
3.Testthelightsasfollows:
A.Turnontheheadlightsofthetowvehicle.
Thetaillightsofthemachineshould
illuminate.
B.Pressthebrakepedalofthetowvehicle.
Thebrakelightsofthemachineshould
illuminate.
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Toro CM-658H-S Concrete Mixer User manual

CM-658H-S Concrete Mixer
Toro
Brand
Toro
Model
CM-658H-S Concrete Mixer
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents