MB QUART MBQ-STG5-1 User manual

Type
User manual

This manual is also suitable for

STAGE 5
800 WATT / FIVE SPEAKER
RZR-Tuned Audio Package
Installation Manual
MBQ-STG5-1
2
©2019 Maxxsonics USA, Inc.
Thanks for choosing MB QUART! The RZR-Tuned Stage 5 Audio System has been meticulously engineered
for your vehicle. The process is simple and straightforward. Installation following these detailed instructions
can be completed in about 3.5 hours.
INSTALLATION OVERVIEW VIDEO
Many of our vehicle-specic products feature
a “how to” install video with additional details
on making your installation successful.
Locate your specic video on the website.
Type your model number (MBQ-STG5-1) into
the search box, then click on the INSTALL &
SUPPORT tab.
WHAT’S INCLUDED
The STG5 system ships in two boxes. Unpackage and account for all components before attempting
installation.
Box 1
AM/FM, Bluetooth Source Unit with a mounting adapter
● Compact 2-channel amplier
● Dual Amplier Harness with mounting hardware
● Dual Amplier Mounting Plate
● Kick Panel Pods
● Two cage-mounted 8-inch Compression Horn Tower Speakers
● Two 8-inch compression horns (kick panel speakers)
● Two compression element diaphragm covers with instructional manual
● USB and 3.5mm dash mount input accessory
● 2 black swivel mount brackets for cage mounting tower speakers
Box 2
● Compact mono subwoofer amplier
● 10-inch subwoofer
● Glove box replacement vented subwoofer enclosure
*RIDE COMMAND
®
-EQUIPPED VEHICLES - If your RZR is equipped with the Ride Command
®
system, you can use
that as the vehicle’s source unit. This requires additional purchase of two adapters (part # RC1-2RCA-F) to connect
into the MB Quart ampliers. The MB Quart source unit is not used in Ride Command-equipped applications.
NOTE – Hardware for mounting components to enclosures and other installation-related items you will need are
contained within the packaging for each piece. Do not dispose of any packaging until you have completely installed
your system and certain you have accounted for every piece. If you feel something is missing, please contact
Maxxsonics directly via email – [email protected].
WARRANTY
Your audio system is covered by a one (1) year warranty from the date of invoice. It is important to retain
your sales receipt. Furthermore, it is crucial that you record and store a record of the serial numbers for
each of the components that are included in your system. In the rare instance that a warranty claim is
needed both proof of purchase and serial numbers are required. Additional information on the back page.
TECHNICAL SUPPORT
For additional technical information, go to the “SUPPORT” tab at MBQUART.com. There you will nd helpful,
FAQ, TEQ Tips and you can contact Technical Support via email.
INTRODUCTION
3
PRE-INSTALLATION
INSTALLATION TIME
About 3.5 hours are required to complete this installation.
TOOLS AND SUPPLIES NEEDED
● Wire Strippers and Crimpers ● Blue Painter’s Tape and Marker Pen
● Flush Cut Wire Cutters (for trimming zip ties) ● Small (Jeweler’s) Screwdriver
● Hand-Held Drill and 5/16” Drill Bit ● Bojo Tools (Pry Tools)
● Ratchet ● Socket (preferably deep)
● 10mm Socket ● 1/2” Open Box Wrench
● T25 Torx Driver ● T40 Torx Driver
Depending on which vehicle-specic which system you are installing, you may or may not need all of the
tools listed below. You may also own more specialized tools to complete the installation. Share the pics of
your installation on our social media channels to help others.
In addition to the tools listed, is helpful to music ready for the TEST & TUNE step. We recommend:
● USB thumb drive with music pre-loaded
● Bluetooth device such as a smartphone with music or a music app
SAFETY PRECAUTIONS
Safely prepare your machine for the installation before
proceeding.
● Turn the ignition off and remove the key
● Remove the negative terminal of the battery (Figure S-1)
● Use a packing blanket other soft material to protect your
machine
● Safety Glasses - always wear eye protection
PREPARATION FOR INSTALLATION
Before dismantling your vehicle, we suggest you prepare
all your components, enclosures and wiring harnesses. It
increases efciency to have everything ready when each
component is installed.
STEP 1 – CONFIRMING POWER TO BUSBAR
(Applies to 2013-2018 RZR Models)
The Polaris RZR and the MB Quart RZR-Tuned Audio
System upgrade requires a harness that connects the
battery under the seat to the busbar harness located under
the hood.
The harness is shown in Figure 1-1. Check that your
2013-2018 machine has this harness installed. If not, you
can purchase from your dealer or Polaris online. The part
numbers are 2881551 or 2881646 depending on which
specic RZR model you own. 2018.5 Turbo S and all 2019+
RZR models already contain a busbar harness.
Figure S-1
Figure 1-1
4
©2019 Maxxsonics USA, Inc.
PRE-INSTALLATION
STEP 2 - PREPARE KICK PANEL COMPRESSION HORNS
Figure 2-1 is from the MBQ-POD manual which guides you
step-by-step through preparing the kick panel compression
horn speakers for installation into the kick panel enclosure
and the RZR.
Removing the large back plate and installing the special
compression horn diaphragm covers dramatically reduces
the depth of the compression horns which ultimately allows
our overall kick panel enclosure to be shallower than you
would think. This assures maximum leg room for driver and
passenger in the vehicle.
Do not proceed with the kick panel installation until you have properly prepared the speakers with their
compression diaphragm covers.
Refer to the manual in the kit called MBQ-POD. You can also nd this manual online by searching the model
number.
STEP 3 - SUBWOOFER ENCLOSURE & MOUNTING CLIPS
STEP 3a – LOCATE MOUNTING CLIPS
If your subwoofer is not pre-installed in the enclosure, you must
prepare the unit by installing the clips that hold the door from
your OEM glove box. See Figure 3-1.
STEP 3b –MOUNT CLIPS
Mount the included hinge brackets for the OEM glove box door
to be tted on to your subwoofer as shown in Figure 3-2 through
3-4. Use the provided nuts to secure the hinge brackets from the
inside of the subwoofer. Do not over tighten.
The hinge clip with the closed hole mounts on the driver side
with the screws on the inside where the glove box door will
cover the screws. See Figure 3-3.
The hinge clip with the open (hook-like) hole mounts on the
passenger side with the screws on the inside where the door will
cover the screws shown. See Figure 3-4.
Figure 2-1
Figure 3-1
Figure 3-2
Figure 3-3 Figure 3-4
5
SUBWOOFER PREP
INSTALL SUBWOOFER INTO ENCLOSURE
STEP 1 - WIRING THE SUBWOOFER*
Set your subwoofer enclosure on a at surface as shown in Figure 4-1. *If you have a 2018.5 Turbo S
or 2019 RZR model, please see the modication required on the next page BEFORE completing the
subwoofer installation into the enclosure.
Put the subwoofer enclosure on its back
and extend the harness from inside
the enclosure as shown. This will allow
you to easily connect the wiring to the
subwoofer’s push-connector terminals.
If your subwoofer was not pre-installed, you will wire the woofer
with the dual voice coils to yield a 2 ohm load (indicated with the Ω
symbol) as pictured in Figure 4-2.
We have prepared the internal harness so you cannot make
a mistake. Wiring the subwoofer for 2 ohms (2Ω) will allow the
subwoofer to develop maximum power from the amplier by perfectly
balancing the impedance with the amplier’s power output.
Use the connection where two wires will insert into one voice coil
connector and then route the other end of the wire to opposite
connector, shown in Figure 4-3 and Figure 4-4.
NOTE – Wiring code is solid white connects to the (+) Positive/Red
speaker terminal and White/Black Stripe connects to the (-) Negative/
Black speaker terminal. To open the speaker terminals push down on
the connector to open, push the soldered ends of the wires through
the hole and release the connector to establish a good electrical
connection.
STEP 2 – SECURE THE SUBWOOFER TO THE ENCLOSURE
Due to the shape of the enclosure it can be very difcult to balance
the subwoofer enclosure and screw in the speaker for one person
shown in Figure 4-5.
To avoid damage to the subwoofer, consider having a friend hold the
enclosure steady while you mount the subwoofer using hand tools
and the screws provided.
It is not advised to use a powered screw gun for this step.
Figure 4-1
Figure 4-2
Figure 4-3
Dual wire on one side.
Single wire on opposite side.
Figure 4-4
Figure 4-5
6
©2019 Maxxsonics USA, Inc.
SUBWOOFER PREP
REMOVE & REINSTALL THE GLOVE BOX DOOR
With a small amount of pressure you can bend up on
the center portion of your OEM glove box door and
remove it from the brackets.
In a reverse movement you can now reinstall this
door onto your new subwoofer glove box to give your
subwoofer a stealth appearance as shown in Figure
5-1.
The subwoofer is now complete. Set aside the
subwoofer enclosure/glove box combination until it’s
time for installation and amplier wiring.
NOTE – Once the subwoofer is ready to be installed, ensure the wiring harness from the subwoofer
enclosure that connects to the amplier does not get pinched behind the enclosure. This will prevent
the enclosure from seating properly and will not allow the front dash to snap into place properly during
reassembly. The harness should be routed over the top of the push bar frame to the subwoofer amplier
connector. This is also noted in the subwoofer installation section, but important to consider at this stage.
SUBWOOFER ENCLOSURE MODIFICATION (2018.5 Turbo S and 2019 Models)
If you have a 2018 XP Turbo S or 2019 RZR XP vehicle, a simple modication to the subwoofer enclosure
which involves cutting four threaded metal studs and grinding them smooth is required. This modication in
no way will affect your product warranty. Complete this modication BEFORE loading the subwoofer into the
enclosure.
PREPARATION - You will need a at surface on which to work and someone to assist you in holding the
enclosure. You’ll also need a cutting tool (such as an Air Saw, Hacksaw, Sawzall) and a metal grinding tool
(such as a Dremel tool, electric disc grinder, etc.). Of course eye protection and heavy gloves are a must for
safety. Total modication time should be 10-15 minutes.
STEP 1 – IDENTIFY METAL STUDS TO BE CUT
Due to change in the metal work in the dash, the 4 front
studs on the enclosure must be removed so that it will
clear the support bar in the 2018 RZR Turbo S, 2019
RZR XP, XP Turbo and Turbo S machines as shown
in Figure 5-2. This is necessary for installation into the
vehicle later in the process.
STEP 2 – CUT OFF METAL STUDS
These 4 studs need to be removed with a cutting tool
(Air Saw, Hacksaw, Sawzall, i.e) or what other cutting
device that you would like to use.
STEP 3 – GRIND SMOOTH
After cutting the studs ush go back with a grinding
device and clean up the area. After removal the
subwoofer enclosure will look like Figure 5-3.
Figure 5-1
Figure 5-2
Figure 5-3
7
DISASSEMBLY
DASH AREA DISASSEMBLY 2013-2018 (Non-Turbo S) RZR
Please note, separate disassembly instructions for the 2018.5 Turbo S and 2019 RZR models are found on
pages 9-11 in this manual.
STEP 1 – REMOVE CENTER HOOD
Start with removing the hood as shown in Figure 6-1.
Twist the tabs at the upper left and right corners. Pull
up to remove. This is where you will access the bus bar
described on page 3 of this manual. Conrm that your
machine has the busbar installed by the dealer or by
you. If your busbar harness has not been installed, you
can purchase from your dealer or Polaris online. The
part numbers are 2881551 or 2881646 depending on
which specic RZR model you own.
STEP 2 - REMOVE TOP OF DASH
Remove (2) T-40 screws as shown in Figure 6-2. Slide dash forward to access back of dash and unplug
gauges and switches one at a time. Set dash aside in a safe location.
STEP 3 – REMOVE THE GRAB BAR
Remove the grab bar as shown in Figure 6-3 by removing the retaining clip and pin and rmly pulling the
grip toward the rear of the vehicle.
STEP 4 - REMOVING DASH POCKET & REAR MOUNT
To remove the DIN dash pocket from the dash, locate the rear support bracket at the rear of the pocket and
remove the Torx head screw as in Figure 6.4a. Next, remove the clip shown on the right from the back and
pull out the plastic pocket. Set aside the retaining clip for re-use when mounting your new dash source unit
as shown in Figure 6-4b.
Figure 6-1
Figure 6-2
Figure 6-3
Figure 6-4a
Torx Screw
Set aside OEM dash clip for source unit
mounting later in the installation.
Figure 6-4b
8
©2019 Maxxsonics USA, Inc.
DASH AREA DISASSEMBLY 2013-2018 (Non-Turbo S) RZR - Continued
STEP 5 – REMOVE DASH FASCIA CENTER HARDWARE
Remove (4) Torx screws from the front of the dash through the openings shown in Figure 6-5a. The rst set
of Torx screws will come out allowing access to the second (upper) set further back in the dash. Next, pull
the only the center of the dash loose as shown in Figure 6-5b.
STEP 6 – REMOVE DASH FASCIA HARDWARE
Using a large panel removal tool, release the side clips from the passenger’s side front dash assembly as
shown in Figure 6-6a and 6-6b. Slowly ensure you account for all clips removed.
STEP 7 – REMOVE THE GLOVE BOX
Remove (2) 10mm bolts on the top of the glove box
where it is fastened to the grab bar framework. See
holes in Figure 6-7. The glove box will easily slide
out. A different mounting method is used for the new
subwoofer.
Go to page 12 for next steps on these model year
vehicles.
Figure 6-5bFigure 6-5a
Figure 6-6bFigure 6-6a
Figure 6-7
DISASSEMBLY
9
DASH AREA DISASSEMBLY 2018.5 Turbo S & 2019 RZR
Please note, separate disassembly instructions for the 2013-2018 RZR models are found on pages 7-8 in
this manual.
STEP 1 – REMOVE CENTER HOOD
Remove the center of the hood area as shown in Figure
7-1. Twist the recessed tabs at the upper left and right
corners. Pull up to remove. Next, pull passenger’s side
grab bar retaining clip and pin, then rmly pulling the grip
toward the rear of the vehicle.
STEP 2 - REMOVE CENTER SHROUD
Remove (2) plastic push clips behind the center shroud as shown in Figure 7-2a to remove the Ride
Command cover or pocket depending on your vehicle. Cover removed shown in Figure 7.2b.
STEP 3 - REMOVE FULL FRONT COVER DASH TOP ASSEMBLY
Remove (2) T-40 screws located by the A-pillars as shown in Figure 7-3a. Next remove the (2) T-40 screws
holding the front of the dash in the inner fender near the water bottle and busbar. Lift upwards to release the
top of the dash cover and remove as shown in Figure 7-3b.
Figure 7-1
Figure 7-2a Figure 7-2b
Figure 7-3a Figure 7-3b
DISASSEMBLY
10
©2019 Maxxsonics USA, Inc.
DASH AREA DISASSEMBLY 2018.5 Turbo S & 2019 RZR - Continued
STEP 4 – REMOVE DYNAMICS ECU BRACKET* AND POCKET SCREW
Remove (4) 10mm bolts holding the Dynamics ECU bracket as shown in Figure 7-4a. Move the ECU to the
side leaving wire connection intact. Even if there is no ECU present, the bracket is still there. Next remove
(1) T40 screw on the pocket support bracket underneath the ECU bracket as shown in Figure 7-4b.
STEP 5 – REMOVE LOWER POCKET AND PASSENGER SIDE CUBBY
Remove lower pocket by pulling forward as shown in Figure 7-5a. If you have Ride Command you will also
have to disconnect the USB cable. Next, remove (2) plastic push clips in the passenger side cubby as
shown in Figure 7-5b. Then remove cubby and set aside.
STEP 6 – REMOVE CENTER SWITCH HARDWARE
Remove (4) T40 screws located above the center
switches as in Figure 7.6a. If you have a Ride
Command, (2) will be on each side of the screen and (2)
behind the screen as in Figure 7.6b.
Figure 7-4a Figure 7-4b
Figure 7-5a Figure 7-5b
Figure 7-6a
Figure 7-6b
DISASSEMBLY
11
DISASSEMBLY
DASH AREA DISASSEMBLY 2018.5 Turbo S & 2019 RZR - Continued
STEP 7 – PREPARE FINAL ELECTRONICS FOR DASH REMOVAL
Gently remove the plastic nut holding the ignition switch to the dash as shown in Figure 7-7a. Next,
disconnect wires from back of switches as shown in Figure 7-7b. Take note of plug color and switch location
for reassembly purposes.
STEP 8– REMOVE DASH FASCIA
Gently pull dash fascia toward seat to remove as shown
in Figure 7-8. Set aside in a safe location until it’s time
for reassembly.
STEP 9 – REMOVE THE GLOVE BOX
Remove (2) 10mm bolts on the top of the glove box
where it is fastened to the grab bar framework. See
holes in Figure 7-9. The glove box will easily slide
out. A different mounting method is used for the new
subwoofer.
Go to page 12 for next steps on all model year RZR vehicles.
Figure 7-7a Figure 7-7b
Figure 7-9
Figure 7-8
12
©2019 Maxxsonics USA, Inc.
DISASSEMBLY
REMOVE SEATS AND CENTER CONSOLE (ALL MODELS)
STEP 1 – REMOVE SEATS
Remove driver and passenger seats by pulling on the lock clip shown in Figure 8-1. This lock clip is located
between the bottom and upright portion of the seat.
Behind the seats in the center of the machine is the panel where you access the oil lter. You will need to
remove this as shown in Figure 8-1b in order to feed and secure the rear speaker harness if not routing the
rear speaker harness inside the body panels.
STEP 2 - UNBOLT AND MARK CENTER CONSOLE HARDWARE
Use the painters tape to mark where you remove each of the push pins and/or T-40 screws in the seat
side and seatbelt area as shown in Figure 8-2a. Remove and mark the nal T-40 screw at the front of the
console. We recommend using small disposable cups or sealable sandwich bags to label the different
screws in order keep track of them for reassembly.
STEP 3 - REMOVE CENTER CONSOLE
Gently push the shifter and seat belt boots back through
the console as show as shown in Figure 8-3. Carefully
remove center console from vehicle. Set aside in a safe
location until it’s time for reassembly.
Figure 8-1a Figure 8-1b
Figure 8-2a Figure 8-2b
Figure 8-3
13
POWER HARNESS
INSTALL POWER HARNESS AT BUSBAR (ALL MODELS)
Before positing the system harness and wiring all the components (source unit, ampliers, subwoofer and
other speakers), you need to prepare the power portion of the audio harness and run into the vehicle.
STEP 1 – REMOVE RZR Busbar FACTORY CONNECTIONS
Remove the connections to the RZR busbar as shown in Figure 9-1 to allow connecting the audio harness
along with reconnecting the RZR busbar harness.
STEP 2 – LAY IN HARNESS - IDENTIFY FIREWALL GROMMET
Beginning at the RZR busbar, route the power, ground and accessory portion of the audio system harness
in the front vehicle. The harness will run through the grommet next to an existing wiring harness as shown in
Figure 9-2. Do not use other grommets if present, empty or not. Use only the grommet shown.
STEP 3 – CUT OPENING IN GROMMET AND RUN WIRING THROUGH
Using a razor knife, carefully slice the rubber grommet on the top side as shown in Figure 9-3a. This allows
you to move the harnesses into the dash and to the ampliers. Push the radio, rear speaker/illumination
and amplier connections through the grommet as in Figure 9-3b. Leave accessible from the inside of the
vehicle. Use black electrical tape or silicone-based caulking to seal the slice during nal inspection.
STEP 4 – COMPLETE BUSBAR CONNECTION
Complete connections at the busbar as shown in Figure
9-4. Mount the MB Quart audio harness rst, with the
OEM RZR connections on top. This allows you to use
the red boot on the powerline, keeping your install clean
and looking factory installed. Zip tie this power portion
of the harness into place. Assure that no added wiring
is near any moving parts or components that generate
large amounts of heat.
Figure 9-1
Figure 9-2
Figure 9-3a Figure 9-3b
Figure 9-4
14
©2019 Maxxsonics USA, Inc.
AMPLIFIER MOUNTING
AMPLIFIER PREPARATION AND MOUNTING (2013-2018 Models)
Before installing the dual amplier plate with the amplier(s) in position, you must prepare the mounting area
in the vehicle to accept the plate.
NOTE - These instructions assume both ampliers and all speakers are present in a full Stage 5 System. If
not all components are present in your system, this makes upgrading much easier.
STEP 1 – LOOSEN STEERING COLUMN NUTS
Loosen the 16mm nuts that secure the steering column to the support frame shown in Figure 10-1a. These
nuts are very hard to loosen. Be careful. Do not remove these steering column nuts, only loosen to create
an 1/8 inch gap between the nut and the frame shown in Figure 10-1b. You will not re-tighten these nuts until
the installation of the whole system is nalized, tested and the vehicle is ready for reassembly.
STEP 2 – AMPLIFIER MOUNTING
Mount your amplier(s) on the dual amplier plate as shown in FIG 10-2 (below). This conguration is critical
to make sure you can access your ne tune adjustments for crossover and bass boost.
STEP 3 – MOUNTING PLATE INSTALLATION
With the ampliers mounted to the plate, slide it into position with the double groove portion of the bracket
sliding between the steering column support shown in 10.1b (above) and the 16mm nuts and washers. Do
not tighten down yet. On the front edge you will secure the plate with the 10mm bolt you removed from the
dash pocket which will also hold the bracket then will ultimately support the new dash pocket with the source
unit. The nished plate should look like Figure 10-3.
You will tighten the 16mm nuts and washers next to the steering column once reassembly of the vehicle
begins. This allows easy removal of the amplier plate for troubleshooting (if necessary).
NOTE - The dual amplier harness is designed and laid out to perfectly connect power and speaker
connections on the driver’s side of the ampliers while the RCA audio connections are on the passenger
side of the RZR.
Figure 10-1a Figure 10-2b
1/8” Gap
1/8” Gap
Figure 10-2 Figure 10-3
10mm
15
AMPLIFIER PREPARATION AND MOUNTING (2018.5 Turbo S & 2019 Models)
Before installing the dual amplier plate with the amplier(s) in position, you must prepare the mounting area
in the vehicle to accept the plate. The area where the ECU bracket was removed and set aside is where the
dual amplier plate installs. If a factory-optioned amplier was present, this would also have been removed.
NOTE - These instructions assume both ampliers and all speakers are present in a full Stage 5 System. If
not all components are present in your system, this makes upgrading much easier.
STEP 1 – SET THE ECU AND BRACKET BACK IN
PLACE*
Set the Dynamics ECU (if present) and ECU mounting
bracket back in its original placement ensuring the wiring
intended for the amplier harness is routed through the
gap area at the forward section of the bracket. Loosely
reattach only the two (2) 10mm rear bolts (nearest the
dashboard) at this point as shown in Figure 10-4. *It is
only important the ECU bracket is back in place for trial
tting of the dual amplier plate. It will not have its nal
reassembly at this step.
STEP 2 – AMPLIFIER MOUNTING
Mount your amplier(s) on the dual amplier plate in
the conguration shown. This conguration is critical to
make sure you can access your ne tune adjustments
for crossover and bass boost.
STEP 3 – TRIAL FITTING THE DUAL AMP PLATE
With the ampliers mounted to the plate, place it into
position atop the ECU bracket as shown in Figure 10-6.
Be sure there is free movement of the wiring harness
with enough length to connect to the amplier’s on-
board connectors. Loosely t the remaining two (2)
10mm bolts from the ECU bracket to check the t of the
dual amp plate. Connect the power and speaker wiring
to the harness as labeled. Do not zip tie anything at this
point as the amp plate will not have its nal reassembly
until after the system has completed testing.
STEP 4 – REMOVE DUAL AMP PLATE AND FLIP
OVER, REMOVE ECU BRACKET
With the ampliers connected to the wiring harness,
place a towel or blanket over the open hood area.
Remove the rst two (2) 10mm bolts for the amp plate,
remove the plate and ip it over on the towel to avoid
scratching the amplier heatsinks. Next remove the
remaining two (2) 10mm bolts from the ECU mount (if
present) and place the ECU to the side as when initially
disassembled on page 10. This will allow you to continue
working on the other steps of the installation until you’re
ready to power up the system, complete nal testing and nalize the reassembly of the ECU bracket and
dual amp plate.
Figure 10-4
Loosely Reattach (2) 10mm
Leave Open
Leave Open
Figure 10-5
Figure 10-6
10mm
10mm
AMPLIFIER MOUNTING
Figure 10-7
16
©2019 Maxxsonics USA, Inc.
SUBWOOFER MOUNTING
SUBWOOFER ENCLOSURE MOUNTING (ALL MODELS)
With the subwoofer installed in the enclosure and the glove box door in position from earlier preparation
steps, you are ready to mount the subwoofer into the glove box location. For those applications on 2018.5
Turbo S and 2019+ RZR models, ensure you’ve completed the modication shown on page 6.
STEP 1 – POSITION AND BEGIN MOUNTING SUBWOOFER_ ENCLOSURE
Sitting on the oor of the RZR, hold the subwoofer enclosure up to the grab bar pipe. Sitting on the oor
of the RZR, hold the subwoofer enclosure up to the grab bar pipe. Mount the subwoofer to the RZR using
the supplied steel plates (2), the (8) nuts, and
(8) washers shown in Figure 11-1. Use your
1/2 inch socket with a small ratchet to begin
tightening the nuts. Space is tight for any larger
tools, a smaller ratchet will work best.
NOTE – Ensure the wiring harness from the
subwoofer does not get pinched behind the
enclosure. This will prevent the enclosure from
seating properly and will not allow the front
dash to snap into place properly The harness
should be routed over the top of the push bar
frame to the subwoofer amplier connector.
STEP 2 – FINISH SUBWOOFER MOUNTING
Tighten a few threads at a time on each bolt to
allow the subwoofer to rise up against the pull
bar frame evenly. This will allow the subwoofer
to seat properly against the frame of the
vehicle. As the subwoofer enclosure comes
up against the grab bar pipe, before it is nally
secure, make sure that the speaker wire is not
behind the enclosure. Once veried, bolt the
subwoofer tightly into place.
NOTE – When the subwoofer starts to seat
into place, push the subwoofer rmly forward
as shown in Figure 11-2 as you tighten the last
thread with the mounting nuts. This forward
pressure will be critical when you reassemble the front
dash for tment into all the clips.
STEP 3 – ROUTE SUBWOOFER HARNESS
Route the subwoofer enclosure’s harness over to the
amplier area. Connect it to the speaker output of the
mono amplier as shown in Figure 11-3.
The next section describes connecting the other wiring
harnesses to the ampliers.
Figure 11-1
Figure 11-2
Push Forward While Tightening
Figure 11-3
Mono
Amplier
Subwoofer Enclosure
17
HARNESS CONNECTIONS
AMPLIFIER AND SPEAKER WIRING HARNESS CONNECTIONS
With your amplier(s) mounted, subwoofer installed and connected to the mono amplier, you can now
begin laying in the front/rear speaker harnesses and plugging in all the remaining connectors.
NOTE - While you are working on your system, we recommend covering the ampliers to avoid scratching
them or inadvertently hitting the crossovers with a wrench or screw driver.
STEP 1 – POWER AND SPEAKER CONNECTORS AT AMPLIFIERS
Plug in the power/ground connector of the two channel and the mono ampliers
respectively. At the same time, if you have illumination, connect the red/black. Next,
connect full range speaker connectors to the two channel amplier. You should
already have connected the subwoofer to the mono amplier in the previous section.
If not, do this step now. See Figure 12-1 for the connection diagram.
STEP 2 – ROUTE FRONT SPEAKER HARNESS
Make sure your front left and front right kick panel
harnesses are set into place.
The left front harness for the kick panel should be
routed down the left side of the steering column to
the kick panel area.
The right front harness for the kick panel needs to
be routed over the subwoofer, not behind, and then
to the kick panel area.
The kick panel pod installation will take place at a
later step. For now, you are simply pre-wiring the
harnesses to their respective areas.
STEP 3 – ROUTE REAR SPEAKER HARNESS
Route rear speaker harness toward rear speakers
through the console area as shown in Figure 12-2.
You can route the remaining harnesses to the rear
pod area by either removing the oil lter cover on
the back wall or route your wires through small
gaps in the body panels.
NOTE – On a four seat RZR (4P RZR) you will need to include the 4P jumper to extend the rear speaker
harness, past the rear seats and then to the rear pod area. See Figure 12-3 for connection.
Figure 12-1
Figure 12-2
Figure 12-3
Main Rear Speaker Harness
Routing Through Console Area
Connection Points to Right Rear Speaker Wiring
Connection Points to Left Rear Speaker Wiring
18
©2019 Maxxsonics USA, Inc.
REAR SPEAKER POD INSTALLATION
Every roll cage angle is a bit different; therefore you should take the time to install the swivel mount
brackets. We suggest you do this on a at surface or work bench.
These brackets are designed to allow 180 degree tilt. This
guaranties that the speaker points directly forward. This exibility
in positioning improves sound quality and overall volume. Refer
to instructions for the swivel bracket packaged with the speaker
pods. Also ensure that the Adjustment Locking Screw is at the
rear of the assembly (not the front) as shown in Figure 13-1.
STEP 1 – TEST MOUNT SPEAKER PODS w/BRACKETS
Stock RZR roll cages use the 1.75 inch tube. If you have an
aftermarket or custom cage you will nd the correct bushings and
mounts included in the box with the pods. Refer to the manual
included with your pods for additional details on mounting and wiring.
Mount the pod and swivel bracket to the roll cage tube. Once the speakers are on the roll cage tube, you
can gently slide the pod up or down on the tube to determine where your nal height will be. Use painter’s
tape to measure and mark a general position so it’s even on both sides. Figures 13-2a and 13-2b show
potential mounting options to try out.
Once the general mounting position is chosen, do not fully tighten the pods as you may want to do nal
adjustments for your ear height after the seat is in position and the system is playing music.
STEP 2 – CONNECT WIRING
Wire up the rear speaker wiring to the speaker pods. If your pods also feature illumination, connect those
wires as well. The harness ran in the vehicle should be color coded and have the correct male/female
connectors to make this an easy task.
Do not zip-tie the wires along the roll cage or gather up excess wire until the system has been fully tested.
REAR SPEAKER PODS
Figure 13-1
Figure 13-2a Figure 13-2b
SWIVEL STRAIGHT
This position offers
MAXX volume
SWIVEL DOWN
This position will have less
volume to riders in the RZR
19
KICK PANEL SPEAKERS
MOUNTING THE KICK PANEL SPEAKERS
Through hundreds of installations, we’ve found once mounting holes are drilled, it’s best to start with the
driver’s side kick panel and then move on to the passenger’s side kick panel to complete the mounting and
wiring of the kick panels. This way you only need the drill out once, then completely nish the left before
moving on to the right. The subwoofer should already be mounted at this stage and both kick panel wires
run to their respective general areas.
STEP 1 – MARK DRILLING SPOTS ON FENDER
Using colored painters tape shown in Figure 14-1a, to mark the interior fender well of the RZR where you
need to drill two mounting holes. To do this, hold an empty left or right pod in your hand. Hold the pod
into place to approximate the position of the mounting holes on the internal fender. Set the unit down and
put colored tape onto the interior fender well area behind the pod until you can see the tape through the
mounting holes when you hold the pod back into place. Next, use a permanent felt-tipped marker to mark
the mount holes on the painter’s tape as shown in Figure 14-1b. Repeat this process on the passenger’s
side kick panel area.
STEP 2 – DRILL HOLES
Drill (2) 5/16 inch mounting holes into the fender where you marked the tape shown in Figure 14-2. Repeat
this process and drill two more 5/16 inch mounting holes on the passenger’s side kick panel area. Remove
any tape in the drilling area from the interior fender wells.
STEP 3 – PUSH OUTER BOLTS THROUGH FENDER AND KICK PANEL
With the included hardware push (1) bolt and (1) washer mount through the fender into the pod. This leaves
only the head of the bolt visible behind the tire shown in Figure 14-3.
NOTE - Wait to mount passenger kick panel until driver’s side
panel is completely mounted and wired.
Figure 14-1a
Figure 14-1b
Figure 14-2
Figure 14-3
20
©2019 Maxxsonics USA, Inc.
KICK PANEL SPEAKERS
STEP 4 – MOUNT KICK PANELS
Using the 5/16 inch bolts, washers, and nuts, mount
the kick panel as shown in Figure 14-4. Make sure you
use a washer on the inside of the enclosure against the
internal wall of the pod which you sandwich against the
fender of the RZR. Use your 1/2 inch ratchet and wrench
to secure the pod.
NOTE - Make sure that the wires behind the enclosure
have remained accessible for connecting to the amplier
harness. Use some painters tape to keep them from
getting blocked by the enclosure if necessary.
STEP 5 – CONNECT WIRE HARNESS INTO KICK PANELS
Connect the wire harness from the amplier that you routed earlier to the wire harness from the kick panel.
STEP 6 – WIRE THE FRONT SPEAKERS
Identify the harness wires from inside of each pod and connect the wires to the back of the compression
horn speakers as shown in Figure 14-5a. Connect speaker wires as shown in Figure 14-5b. If your kick
panel speakers also feature illumination, connect those wires as well.
STEP 7 – MOUNT THE FRONT SPEAKERS
With the speakers properly wired, mount the speaker to the enclosure. Position the speaker (with the
compression horn backplate removed) in the enclosure and mount with the included hardware as shown in
Figure 14-6a. We suggest mounting with hand tools to stripping out the mounting hardware or damaging the
speakers. Final speaker position is shown in Figure 14-6b. Repeat steps 3-7 on the passenger’s side.
NOTE - Refer to the compression horn diaphragm replacement manual included with the speakers called
MBQ-POD if you have not yet remove the back plate to accommodate the kick panel depth.
Figure 14-4
Figure 14-5a
Figure 14-6a Figure 14-6b
Figure 14-5b
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

MB QUART MBQ-STG5-1 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI