H3C S12516X-AF User manual

Brand: H3C

Model: S12516X-AF

Type: User manual

This manual is also suitable for

Contents

Installing FRUs ················································································ 1

Attaching an ESD wrist strap ········································································································ 1

Installing MPUs ························································································································· 2

Installing MPUs for the S12516X-AF, S12512X-AF, and S12508X-AF switches ································ 3

Installing MPUs for the S12504X-AF switch ·············································································· 4

Installing MPUs for the S12502X-AF switch ·············································································· 5

Installing LPUs ·························································································································· 6

Installing S12500-X LPUs ····································································································· 7

Installing S12500X-AF LPUs ································································································ 10

Installing an LPU with common ejector levers ·········································································· 11

Installing an LPU with foldable ejector levers ··········································································· 12

Installing cable management brackets ·························································································· 14

Installing switching fabric modules ······························································································· 14

Installing a filler panel in a switching fabric module slot ······························································ 16

Removing a filler panel from a switching fabric module slot ························································ 17

Installing fan trays ···················································································································· 18

Installing fan trays for S12516X-AF, S12512X-AF, and S12508X-AF switches ································ 19

Installing fan trays for an S12504X-AF switch ·········································································· 20

Installing fan trays for an S12502X-AF switch ·········································································· 21

Installing fan trays for an S12501X-AF switch ·········································································· 22

Installing power modules ··········································································································· 23

Connecting the power cord ········································································································ 25

Connecting an AC power cord ······························································································ 25

Connecting a DC power cord ······························································································· 26

(Optional) Installing a DC input terminal block ·········································································· 26

Installing transceiver modules ····································································································· 27

Installing an SFP+/SFP/QSFP+/QSFP28 module ····································································· 28

Installing a CFP2 module ···································································································· 29

Installing a CXP module ······································································································ 30

Connecting a CXP fiber cable ······························································································ 31

Connecting an SFP+/QSFP+/QSFP28/QSFP+ to SFP+ copper cable ·········································· 31

Installing FRUs

As a best practice, connect power cords after installing all required FRUs. To ensure good ventilation,

install filler panels on unused slots.

Long-time exposure to strong air flow might cause discomfort. To avoid this hazard, do not stand

close to the air outlet vents while the switch is operating. If you must be next to the switch on the air

outlet vent side for an extended period, avoid the air flow or take other protective measures.

TIP:

Keep the chassis and the component packages for future use.

Attaching an ESD wrist strap

An S12501X-AF switch does not have an ESD jack and no ESD wrist strap is provided with it.

Prepare an ESD wrist strap for the switch yourself and ground the strap reliably.

The other S12500X-AF switch models each are provided with an ESD wrist strap. To minimize ESD

damage to electronic components, wear the ESD wrist strap and make sure it is reliably grounded

before you install FRUs.

To attach an ESD wrist strap:

1. Make sure the switch is reliably grounded. For information about how to ground your switch,

see "Installing the switch."

2. Put on the wrist strap.

3. Tighten the wrist strap to make sure it makes good skin contact. Make sure the resistance

reading between your body and the ground is between 1 and 10 megohms.

4. As shown in Figure 1, ins

ert the ESD wrist strap into the ESD jack on the chassis.

Figure 1 Attaching an ESD wrist strap (S12516X-AF switch)

(1) ESD jack (with an ESD sign)

Installing MPUs

CAUTION:

• If you are not to install an MPU in an MPU slot, keep the filler panel in the slot.

• Before you install an MPU in the chassis, make sure the connectors on the MPU are not broken

or blocked.

• When you install an MPU, avoid damaging the connectors on the MPU.

• To prevent a filler panel from being drawn into the chassis when fan speed is high, use both

hands to grasp the filler panel by its two sides during filler panel installation and removal on an

operating switch.

An S12501X-AF switch does not require MPUs.

Unless otherwise stated, the term "MPU" in this document refers to MPUs and cloud SEUs.

For the compatibility between the switch and the MPUs, see "Appendix B FRUs and compatibility

matrixes."

You can install one MPU, or two MPUs for redundancy on the switch. If you are to install one MPU,

install it in either of the MPU slots.

Installing MPUs for the S12516X-AF, S12512X-AF, and

S12508X-AF switches

For the S12516X-AF, S12512X-AF, and S12508X-AF switches, the ejector levers of the MPUs and

the ejector lever seats on the MPU slots have pink marks. The MPU installation procedure is the

same for the S12516X-AF, S12512X-AF, and S12508X-AF switches. The following uses the

S12516X-AF switch as example.

To install an MPU:

1. As shown by callout 1 in Figure 2, remo

ve the filler panel from the target MPU slot.

Keep the removed filler panel secure for future use.

2. As shown by callout 2 in Figure 2, o

rient the MPU with lettering on it upright. Hold the MPU by

the front panel with one hand and support the bottom with the other. Push the MPU steadily into

the slot along the guide rails.

Keep the MPU parallel to the slot to avoid touching other components in the chassis.

3. As shown by callout 3 in Figure 2, pull the ejecto

r levers of the MPU outward when most part of

the MPU is inserted in the slot.

4. Push the MPU until the brakes on its ejector levers touch the slot edges tightly.

5. As shown by callout 4 in Figure 2, Conti

nue to push the MPU by its middle part on the front

panel until you cannot move it.

6. As shown by callout 5 in Figure 2, pu

sh the ejector levers inward until they come in close

contact with the front panel.

7. As shown by callout 6 in Figure 2, fa

sten the captive screws on the MPU.

Figure 2 Installing an MPU (S12516X-AF switch)

(1) Loosen the captive screws and remove the filler panel (2) Insert the MPU into the slot

(3) Pull the ejector levers outward

(4) Push the MPU by the middle part on the front panel

(5) Pull the ejector levers inward (6) Fasten the captive screws on the MPU

Installing MPUs for the S12504X-AF switch

The S12504X-AF switch MPU marks and MPU slot edges are pink-marked.

To install an MPU for the S12504X-AF switch:

1. As shown by callout 1 in Figure 3, remo

ve the filler panel from the target MPU slot.

Keep the removed filler panel secure for future use.

2. As shown by callout 2 in Figure 3, pivot up the han

dle of the MPU.

3. As shown by callout 3 in Figure 3, o

rient the MPU lettering on it upright. Holding the MPU by the

front panel with one hand and supporting the bottom with the other, push the MPU steadily into

the slot along the guide rails.

Keep the MPU parallel to the slot to avoid touching other components in the chassis.

4. As shown by callout 4 in Figure 3, pu

sh the MPU until the handle breaks touch the slot edges

tightly.

5. As shown by callout 5 in Figure 3, co

ntinue to push the MPU handle until the MPU is secure in

position.

6. Fasten the captive screws on the MPU.

Figure 3 Installing an MPU (S12504X-AF switch)

(1) Loosen the captive screws and remove the filler panel

(2) Pivot up the handle

(3) Push the MPU into the slot along the guide rails

(4) Push the MPU until the handle breaks touch the slot edges tightly

(5) Push the handle until the MPU is secure in position (6) Fasten the screws on the MPU

Installing MPUs for the S12502X-AF switch

The S12502X-AF switch MPU has pink marks.

To install an MPU for the S12502X-AF switch:

1. As shown by callout 1 in Figure 4, remo

ve the filler panel from the target MPU slot.

Keep the removed filler panel secure for future use.

2. As shown by callout 2 in Figure 4, pre

ss the latch on the MPU to release the ejector lever. Fully

open the ejector lever.

3. As shown by callout 3 in Figure 4, orie

nt the MPU with the upside up. Hold the MPU by the front

panel with one hand and support the bottom with the other. Push the MPU steadily into the slot

along the guide rails until it has firm contact with the slot.

Keep the MPU parallel to the slot to avoid touching other components in the chassis.

4. As shown by callout 4 in Figure 4, close the ejector lever until the latch locks the ejector lever in

place.

Figure 4 Installing an MPU

Installing LPUs

CAUTION:

• Before you install an LPU on the switch, make sure the connectors on the LPU are not damaged

or blocked.

• To prevent a filler panel from being drawn into the chassis when fan speed is high, use both

hands to grasp the filler panel by its two sides during filler panel installation and removal on an

operating switch.

CAUTION:

To prevent card damage and ensure correct operation, LPUs can only be used with switching fabric

modules of the same type.

• Type T LPUs have a character T in their card identifier (for example, LSXM1CGQ36TD1). Type T

switching fabric modules have a character string of SFT in their card identifier (for example,

LSXM1SFT16E1).

• Type H LPUs have a character of H in their card identifier (for example, LSXM1CGQ36HB1).

Type H switching fabric modules have a character string of SFH in their card identifier (for

example, LSXM1SFH16C1).

• Type F LPUs have a character of F in their card identifier (for example, LSXM1CGP12FX1). Type

F switching fabric modules have a character string of SFF in their card identifier (for example,

LSXM1SFF16C1).

For the compatibility between the switch and the LPUs (also called interface modules), see

"Appendix B FRUs and compatibility matrixes."

The S12501X-AF and S12502X-AF switches support only S12500X-AF Type H LPUs.

Installing S12500-X LPUs

The S12500X-AF switch supports only FX and FE series S12500-X LPUs. To install an S12500-X

LPU on the switch, first install an interface module adapter in the LPU slot.

CAUTION:

For heat dissipation of the switch, you must install an LPU in the slot where an interface module

adapter is installed. If you are not to install an LPU in the slot, remove the interface module adapte

and install a filler panel.

Installing an interface module adapter

1. Remove the filler panel from the target slot. See callout 1 in Figure 2.

Keep the removed filler panel secure for future use.

2. As shown in Figure 5, alig

n the adapter rear with the LPU slot and push the adapter slowly

along the guide rails into the slot.

3. As shown by callout 2 in Figure 5, use the scre

ws provided with the interface module adapter to

secure the adapter to the chassis.

Figure 5 Installing an interface module adapter (S12516X-AF switch)

(1) Push the interface module adapter slowly along the guide rails into the slot

(2) Fasten the screws to secure the interface module adapter to the chassis

Installing an S12500-X LPU

The S12500-X LPU edges and the ejector lever seats on the LPU slots have purple marks.

To install an S12500-X LPU:

1. As shown in Figure 6, lo

osen the captive screws that secure the LPU to the protection box, pull

the ejector levers of the LPU outward, and pull out the LPU from the protection box. .

2. Orient the LPU with the PCB facing up. Hold the LPU by the front panel with one hand and

support its bottom with the other. Slide the LPU steadily into the target slot along the guide rails.

See Figure 7.

Do not tou

ch the components on the PCB.

Keep the LPU parallel to the slot to avoid touching other components in the chassis.

3. As shown by callout 2 in Figure 7, pull th

e ejector levers outward when most of the LPU is

inserted into the slot.

4. Push the LPU until the brakes on its ejector levers touch the slot edges tightly.

5. As shown by callout 3 in Figure 7, co

ntinue to push the LPU by its middle part on the front panel

until you cannot move it.

6. As shown by callout 4 in Figure 7, pu

sh the ejector levers inward until they come in close

contact with the panel.

7. As shown by callout 5 in Figure 7, fasten

the captive screws to secure the LPU to the interface

module adapter.

Figure 6 Removing an S12500-X LPU from the protection box

(1) Loosen the captive screws that secure the LPU to the protection box

(2) Pull the ejector levers outward

(3) Pull the LPU out of the protection box

Figure 7 Installing an S12500-X LPU (S12516X-AF switch)

(1) Push the LPU slowly along the guide rails into the slot (2) Pull the ejector levers outward

(3) Push the LPU by the middle part on the front panel (4) Pull the ejector levers inward

(5) Fasten the captive screws on the LPU

Installing S12500X-AF LPUs

CAUTION:

• The S12501X-AF and S12502X-AF switches support only S12500X-AF Type H LPUs.

• A protective blank panel is installed over LPU slots on the S12502X-AF to avoid damage during

transportation. Before you install an LPU on the S12502X-AF, remove the protective blank panel

first.

IMPORTANT:

Keep filler panels installed on unused LPUs.

No interface module adapter is required to install an S12500X-AF LPU on the switch.

The S12500X-AF LPU ejector levers and the ejector lever seats on the LPU slots have purple marks.

Installing an LPU with common ejector levers

1. As shown by callout 1 in Figure 8, remove the filler panel from the target LPU slot.

Keep the removed filler panel secure for future use.

2. As shown by Figure 8, orie

nt the LPU upside up based on the orientation of characters on the

LPU. Holding the LPU by the front panel with one hand and supporting the bottom with the other,

push the LPU steadily into the slot along the guide rails.

Keep the LPU parallel to the slot to avoid touching other components in the chassis.

3. As shown by callout 2 in Figure 8, pull the ejector leve

rs of the LPU outward when most part of

the LPU is inserted in the slot.

4. Push the LPU until the brakes on its ejector levers touch the slot edges tightly.

5. As shown by callout 3 in Figure 8, Conti

nue to push the LPU by its middle part on the front panel

until you cannot push it further.

6. As shown by callout 4 in Figure 8, pu

sh the ejector levers inward until they come in close

contact with the front panel.

7. As shown by callout 5 in Figure 8, fa

sten the captive screws on the LPU.

Figure 8 Installing an LPU with common ejector levers (S12516X-AF switch)

(1) Push the LPU slowly along the guide rails into the slot (2) Pull the ejector levers outward

(3) Push the LPU by the middle part on the front panel (4) Pull the ejector levers inward

(5) Fasten the captive screws on the LPU

Installing an LPU with foldable ejector levers

1. Orient the LPU with the lettering on it upward.

2. As shown by callout 1 in Figure 9, hol

ding the LPU by the front panel with one hand and

supporting its bottom with the other, slide the LPU gently into the slot along the slide rails.

Keep the LPU parallel to the slot to avoid damaging other components in the chassis.

3. When most part of the LPU is inserted into the slot, simultaneously pivot the ejector levers

towards each other until they stop, as shown by callout 2 in Figure 9.

4. As sho

wn by callout 3 in Figure 9, rotate

the ejector levers away from the front panel until they

stop.

5. As shown by callout 4 in Figure 9, push the LPU by its middle part on the front panel until you

cannot move it.

6. As shown by callout 5 in Figure 9, pu

sh the ejector levers inward towards the front panel.

7. As shown by callout 6 in Figure 9, fa

sten the captive screws to secure the LPU in the chassis.

8. As shown by callout 7 in Figure 9, rotate

the ejector levers upward to the vertically closed

position.

Figure 9 Installing an LPU with foldable ejector levers (S12516X-AF switch)

(1) Push the LPU slowly into the slot along the slide rails

(2) Rotate the ejector levers towards each other until they stop

(3) Rotate the ejector levers away from the front panel until they stop

(4) Push the LPU by the middle part on the front panel

(5) Push the ejector levers inward towards the front panel

(6) Fasten the captive screws on the LPU

(7) Rotate the ejector levers upward to the vertically closed position

Installing cable management brackets

For an S12501X-AF switch, the cable management brackets come attached to the mounting

brackets and do not require separate installation.

The cable management brackets are installed on the two sides of the LPU slots. As a best practice,

install cable management brackets after you have installed LPUs.

As shown in Figure 10, insert the cable

management bracket end that has a spring tab into the cable

management bracket hole until the bracket has close contact with the hole.

Figure 10 Installing a cable management bracket (S12516X-AF switch)

(1) Spring tab on the cable management bracket

(2) Align the cable management bracket with the bracket hole

NOTE:

You must press the spring tab while removing a cable management bracket.

Installing switching fabric modules

CAUTION:

• Before you install a switching fabric module on the switch, make sure the connectors on the

switching fabric module are not damaged or blocked.

• When you install a switching fabric module, avoid damaging the connectors on it.

• Install switching fabric modules or switching fabric module slot filler panels before you install the

fan tray.

• Install filler panels in the empty switching fabric module slots.

• To replace or install a switching fabric module for an operating device, first remove the fan tray

that covers the slot of the switching fabric module. Install the fan tray immediately after the

replacement or installation. After the fan tray starts operating, you can replace or install switching

fabric modules whose slots are covered by the other fan tray.

• The smart speed adjustment feature increases the fan speed when only one fan tray is operating.

Take noise protection measures such as wearing an earmuff or earplug. In addition, make good

preparation before hot swapping a switching fabric module to minimize the operation time.

CAUTION:

The S12516X-AF, S12512X-AF, S12508X-AF, and S12504X-AF switches use slots 18 to 23, 14 to

19, 10 to 15, and 6 to 11 for switching fabric modules, respectively.

• To use an LSXM1TGS24FX1 LPU, the three lowest-numbered switching fabric module slots take

precedence over other slots for module installation. For an LSXM1TGS24FX1 LPU to start up

correctly, install a minimum of one switching fabric modules in the three lowest-numbered

switching fabric module slots.

• To use an LSXM1TGS48C2HB1, LSXM1TGS48HB1, LSXM1TGS48HF1,

LSXM1CGQ6QGHB1, LSXM1CGQ6QGHF1, or LSXM1TGS24QGMODHB1 LPU, the three

highest-numbered switching fabric module slots take precedence over other slots for module

installation. For the LPU to start up correctly, install a minimum of one switching fabric modules in

the three highest-numbered switching fabric module slots.

• To use an LSXM1QGS24HB1, LSXM1QGS36HB1, LSXM1TGS48QGHA1, or

LSXM1TGS24CGMODHD1 LPU, the four highest-numbered switching fabric module slots take

precedence over other slots for module installation. For the LPU to start up correctly, install a

minimum of one switching fabric modules in the four highest-numbered switching fabric module

slots.

CAUTION:

To prevent card damage and ensure correct operation, switching fabric modules can only be used

with LPUs of the same type.

• Type T switching fabric modules have a character string of SFT in their card identifier (for

example, LSXM1SFT16E1). Type T LPUs have a character of T in their card identifier (for

example, LSXM1CGQ36TD1).

• Type H switching fabric modules have a character string of SFH in their card identifier (for

example, LSXM1SFH16C1). Type H LPUs have a character of H in their card identifier (for

example, LSXM1CGQ36HB1).

• Type F switching fabric modules have a character string of SFF in their card identifier (for

example, LSXM1SFF16C1). Type F LPUs have a character of F in their card identifier (for

example, LSXM1CGP12FX1).

The S12501X-AF and S12502X-AF switches do not require switching fabric modules.

For the compatibility between the switch and the switching fabric modules, see "Appendix B FRUs

and compatibility matrixes."

The switch has six vertically-oriented switching fabric module slots at the chassis rear. The switch

comes with all switching fabric module slots empty. You can install two to six switching fabric

modules for the switch. Install switching fabric module slot filler panels in the empty switching fabric

module slots.

To install a switching fabric module:

1. Place the switching fabric module on a workbench and remove the protection box from the

connector side of the switching fabric module. See Figure 11.

2. Rele

ase the ejector levers by pressing the spring clips.

3. Orient the switching fabric module with the side marked "Up" up. Hold the switching fabric

module front panel near the ejector levers with one hand and support the module bottom with

the other. Place the module bottom on the guide rails at the chassis bottom. Align the switching

fabric module with the target slot and insert it into the slot along the guide rails. See callout 1

in Figure 12.

Keep the mo

dule parallel to the slot to avoid touching other components in the chassis.

4. As shown by callout 2 in Figure 12,

continue to push the switching fabric module until the brakes

on its ejector levers touch the slot edges tightly. Simultaneously rotate the ejector levers inward

until the spring clips lock the ejector levers in place and the switching fabric module is

completely seated in the slot.

Figure 11 Removing the switching fabric module from the protection box (S12516X-AF

switching fabric module)

(1) Five screws to secure the protection box to the switching fabric module (2) Loosen the captive screws

(3) Hold the protection box to disengage it from the connector side of the switching fabric module

Figure 12 Installing a switching fabric module (S12516X-AF switch)

(1) Push the switching fabric module slowly into the slot

(2) Rotate the ejector levers inward until the spring clips lock the ejector levers in place

Installing a filler panel in a switching fabric module slot

The switch comes with empty switching fabric module slots. Install a filler panel in a switching fabric

module slot if you are not to install a switching fabric module in it.

To install a filler panel in a switching fabric module slot:

1. Loosen the captive screws on the ejector levers and rotate outward the ejector levers.

2. Orient the filler panel with the side marked "Up" up. Hold the filler panel front panel near the

ejector levers with one hand and support its bottom with the other. Place the filler panel bottom

gently on guide rails at the chassis bottom. Align the filler panel with the switching fabric module

slot. Push the filler panel slowly into the slot along the guide rails. See callout 1 in Figure 13.

Keep the filler panel pa

rallel to the switching fabric module slot to avoid touching other

components in the chassis.

3. As shown by callout 2 in Figure 13,

continue to push the filler panel until the brakes on its ejector

levers touch the slot edges tightly. Simultaneously rotate the ejector levers inward.

4. Fasten the captive screws on the ejector levers.

Figure 13 Installing a filler panel in a switching fabric module slot (S12516X-AF switch)

(1) Push the filler panel slowly into the slot (2) Simultaneously rotate the ejector levers inward

(3) Fasten the captive screws on the ejector levers

Removing a filler panel from a switching fabric module slot

1. As shown by callout 1 in Figure 14, loosen the captive screws on the ejector levers.

2. As shown by callout 2 in Figure 14, rotat

e outward the ejector levers. Then pull the filler panel

part way out of the slot.

3. As shown by callout 3 in Figure 14, hold

the filler panel by the top and bottom edges to pull the

filler panel out of the slot.

Keep the removed the filler panel secure for future use.

Figure 14 Removing a filler panel from a switching fabric module slot (S12516X-AF switch)

(1) Loosen the captive screws on the ejector levers (2) Rotate the ejector levers outward

(3) Pull the filler panel out of the slot along the guide rails

Installing fan trays

WARNING!

When removing the fan tray, keep your hands and fingers away from the spinning fan blades. Let the

fan blades completely stop before you remove the fan tray.

CAUTION:

• To avoid fan tray damage, use both hands when installing or removing a fan tray.

• To prevent dust from entering the chassis, make sure each fan tray slot has a filler panel or fan

tray installed when the switch is not in use.

CAUTION:

When you hot swap fan trays, follow these guidelines:

• Ensure electricity safety.

• For an S12501X-AF switch, you can hot swap a fan tray only when the other two fan trays are

operating correctly. For the other S12500X-AF switch models, you can hot swap a fan tray only

when the other fan tray is operating correctly.

• When you hot swap a fan tray, the fan speed of the remaining fan trays automatically increases.

Take noise protection measures such as wearing an earmuff or earplug. In addition, make

preparations before hot swapping a fan tray to minimize the operation time.

IMPORTANT:

A fan tray covers switching fabric module slots. Install the switching fabric modules or filler panels in

the switching fabric module slots before installing a fan tray.

An S12501X-AF switch has three fan tray slots and supports 2+1 fan tray redundancy. The other

S12500X-AF switch models each have two fan tray slots. You can install one fan tray, or two fan trays

in 1+1 redundancy for the switch. As a best practice, install a fan tray in each slot for redundancy and

to reduce noises.

Installing fan trays for S12516X-AF, S12512X-AF, and

S12508X-AF switches

IMPORTANT:

The fan tray is high and heavy. To avoid device damage and bodily injury, use two people to install

or remove a fan tray.

To install a fan tray for the S12516X-AF, S12512X-AF, or S12508X-AF switch:

1. Orient the fan tray with the upside up based on the orientation of characters on the fan tray and

align the fan tray with the fan tray slot.

2. Holding the upper fan tray handle with one hand and the lower fan tray handle with the other

hand, insert the fan tray into the slot. Keep the fan tray as straight as possible.

To install a fan tray in FAN1 slot, align the top and left edges of the fan tray in the slot. To install

a fan tray in FAN2 slot, align the top and right edges of the fan tray in the slot.

3. Fasten the captive screws on the fan tray.

Page is loading ...

H3C S12516X-AF User manual

Brand: H3C

Model: S12516X-AF

Type: User manual

This manual is also suitable for

Download PDF

report

H3C S12516X-AF User manual

This manual is also suitable for

H3C S12516X-AF User manual

Related papers

Other documents