Wolf CTWH30 Operating instructions

Brand: Wolf

Model: CTWH30

Category: Cookers

Type: Operating instructions

CT & CTE HOODS

DD & ICBDD VENTILATION

(Including Parts Lists and Exploded Views)

1-1

General Information CT Hoods and DD Ventilation

SECTION 1

GENERAL INFORMATION

1-2

General InformationCT Hoods and DD Ventilation

INTRODUCTION

This Wolf Cooktop and Downdraft Ventilation Technical Service Manual, has been compiled with information provided

by Broan-Nu Tone LLC. This manual provides the most recent technical service information that will enable the

service technician to troubleshoot and diagnose malfunctions, perform necessary repairs and return a Wolf Ventilation

product to proper operational condition.

The service technician should read the complete instructions contained in this Service Manual before initiating any

repairs on a Wolf Appliance.

IMPORTANT SAFETY INFORMATION

Below are the Product Safety Labels used in this manual.

The “Signal Words” used are WARNING & CAUTION.

Please note that these safety labels are placed in areas

where awareness of personal safety and product safety

should be taken and lists the precautions to be taken when

the signal word is observed.

INDICATES THAT HAZARDOUS OR UNSAFE

PRACTICES COULD RESULT IN SEVERE

PERSONAL INJURY OR DEATH

Indicates that hazardous or unsafe practices

could result in minor personal injury or product

and/or property damage

In addition, please pay attention to the signal

word “NOTE”, which highlights especially

important information within each section.

TECHNICAL ASSISTANCE

If you should have any questions regarding a Wolf

appliance and/or this manual, please contact:

Wolf Appliance, Inc.

ATTN.: Service Department

P.O. Box 44988

Madison, WI 53744-4988

Customer Service

Phone #: (800) 332 - 9513

Technical Assistance

Phone #: (800) 919 - 8324

Parts / Warranty Claims

Phone #: (800) 332 - 9513

Customer Service E-mail Address

[email protected]

Customer Service & Technical Assistance

Facsimile #: (608) 441 - 5887

Parts / Warranty Claims

Facsimile #: (608) 441 - 5886

Ofﬁ ce Hours:

7:00 AM to 7:00 PM Central Standard Time

Monday through Friday

This manual is designed to be used by Authorized Service Personnel only. Wolf Appliance, Inc. assumes no

responsibility for any repairs made to Wolf appliances by anyone other than Authorized Service Technicians.

The information and images contained in this manual are the copyright property of Wolf Appliance, Inc., an afﬁ liate of Sub-Zero,

Inc. Neither this manual nor any information or images contained herein may be copied or used in whole or in part without the

1-3

General Information CT Hoods and DD Ventilation

Page #

Section 1 - General Information ...................... 1-1

Introduction ........................................................ 1-2

Important Safety Information ............................. 1-2

Technical Assistance ......................................... 1-2

Table of Contents ............................................... 1-3

Warranty Information ......................................... 1-4

Model Descriptions ............................................ 1-5

Section 2 - Installation Information ............... 2-1

CT & Island Hood Overall Dimensions .............. 2-2

CTEWH Overall Dimensions ............................. 2-3

CTEIH Overall Dimensions ................................ 2-4

CT Hood Placement ........................................... 2-5

CT Wall Hood Installation Considerations ......... 2-6

CT Wall Hood Installation .................................. 2-7

Ductwork Installation ......................................... 2-8

Island Hood Installation Considerations ............ 2-9

Island Hood Installation ..................................... 2-10

Hood Internal Blower Installation ...................... 2-12

CTE Hood Installation Considerations .............. 2-13

CTEW Hood Installation Speciﬁ cations ............ 2-14

CTEW Hood Electrical Requirements ............... 2-15

CTEW Hood Installation .................................... 2-15

CTEI Hood Installation Speciﬁ cations ............ 2-17

CTEI Hood Electrical Requirements ............... 2-18

CTEI Hood Installation .................................... 2-18

Hood Remote Blower Installation ....................... 2-20

Downdraft Dimensions ...................................... 2-21

Downdraft Installation Speciﬁ cations ................ 2-22

Downdraft Installation Requirements ................ 2-23

Downdraft Ducting Considerations ................... 2-24

Downdraft Blower Discharge ............................ 2-25

Downdraft Installation ....................................... 2-25

DD Internal Blower Installation .......................... 2-26

DD Remote Blower Installation ......................... 2-26

Section 3 - Controls & Operation ................... 3-1

Electronic Control for CT Wall Hoods ............... 3-2

Heat Sentry Mode ............................................. 3-2

Electronic Control for Downdraft ....................... 3-3

Cleaning ............................................................ 3-3

Electronic Control for Low Proﬁ le Hoods .......... 3-4

Section 4 - Access and Removal ................... 4-1

CT Hoods:

Filter Removal ................................................... 4-2

Bulb and Light Assembly ................................... 4-3

Heat Sentry ....................................................... 4-4

Control Interface ................................................ 4-4

Power Outlet ...................................................... 4-5

Transformer ........................................................ 4-6

Fuse ................................................................... 4-6

TABLE OF CONTENTS

Page #

Section 4 - Access and Removal (continued)

CTE Hoods:

Bulb Removal .......................................................... 4-7

Filter Removal ......................................................... 4-7

Inside Panel ............................................................. 4-7

Lamp Socket ............................................................ 4-8

Control Panel Removal ............................................ 4-8

Internal Blower Removal .......................................... 4-9

Control Board Removal ............................................ 4-10

Downdrafts:

Filter Removal .......................................................... 4-11

Internal Blower Removal .......................................... 4-12

Cam Switch Removal ............................................... 4-13

Front Air Box Removal ............................................. 4-13

Gear Motor Removal ................................................ 4-14

Power Control Board Removal ................................. 4-15

Section 5 - Troubleshooting .................................. 5-1

Ventilation Troubleshooting Chart ............................ 5-3

Downdraft Troubleshooting Chart ............................ 5-4

Low Proﬁ le Troubleshooting Chart ........................... 5-5

Downdraft Cam Switch Operation ............................ 5-6

Downdraft Seal Damage Flow Chart ........................ 5-7

Section 6 - Technical Data ..................................... 6-1

Voltage and Temperature Parameters (CT & DD) .... 6-2

Voltage Parameters (CTE) ........................................ 6-3

Section 7 - Wiring Diagram ................................... 7-1

CTWH30 Wiring Diagram ........................................ 7-2

CTWH36 Wiring Diagram ....,................................... 7-3

IH4227 Wiring Diagram ........................................... 7-4

Low Proﬁ le Hood Wiring Diagram ............................ 7-5

Downdraft Schematic .............................................. 7-6

Downdraft Wiring Diagram ...................................... 7-7

ICBDD Schematic .................................................... 7-8

ICBDD Wiring ........................................................... 7-9

Downdraft Control Schematic .................................. 7-10

Downdraft Power Supply Wiring .............................. 7-11

CT & IH Hood Power Supply Wiring ........................ 7-12

Blower Wiring ........................................................... 7-13

Section 8 - Parts List and Exploded Views ......... 8-1

CT Hood Parts List .................................................. 8-2

CT Hood Exploded View ......................................... 8-3

IH4227 Parts List ..................................................... 8-4

IH4227 Exploded View ............................................ 8-5

CTEWH30I, 36I, 45I Parts List ................................ 8-6

CTEWH30I, 36I, 45I Exploded View ....................... 8-7

CTEWH36, 45 Parts List ......................................... 8-8

CTEWH36, 45 Exploded View ................................ 8-9

CTEIH42 Parts List ................................................. 8-10

CTEIH42 Exploded View ........................................ 8-11

Downdraft Parts List ................................................ 8-12

Downdraft Exploded View ........................................ 8-13

ICBDD Parts List ...................................................... 8-14

ICBDD Exploded View ............................................. 8-15

1-4

General InformationCT Hoods and DD Ventilation

WARRANTY INFORMATION

This page contains a summary of the Warranty supplied

with every Domestic Wolf ventilation product, followed by

details about the warranty.

NOTE: “ICB” warranties vary by Country and Distributor.

Contact selling Distributor for warranty coverage.

2 & 5 Y

EAR WARRANTY SUMMARY

2 YEAR TOTAL PRODUCT WARRANTY, • Parts and Labor.

3-5 • LIMITED *PARTS ONLY WARRANTY (Including Blower

motors).

DETAILS:

Warranty applies to products installed in United States •

or Canada, for residential use only.

Warranty begins at time of unit’s initial installation.•

This Warranty does not cover Wolf Appliances installed •

in a demonstration kitchen, test kitchen, culinary school

kitchen, or similar installations. (See Special Warranty

below)

Warranty and Service information collected by Wolf •

Appliance, Inc. is arranged and stored under unit serial

number and/or customer’s name. Please note that Wolf

Appliance, Inc requests that you have model and serial

number available whenever contacting factory or parts

distributor.

SPECIAL WARRANTY SUMMARY

2 YEAR TOTAL PRODUCT WARRANTY, • Part and Labor.

DETAILS:

This Warranty applies to products installed in United •

States or Canada, for use in a demonstration kitchen,

test kitchen, culinary school kitchen, and similar instal-

lations that will help promote Wolf Appliance brand and

its products.

Warranty begins at time of unit’s initial installation.•

Warranty and Service information collected by Wolf •

Appliance, Inc. is arranged and stored under unit serial

number and/or customer’s name. Please note that

Wolf Appliance, Inc. requests that you have model and

serial number available whenever contacting factory or

parts distributor.

INFORMATION PLATE AND SERIAL NUMBER

See Figure 1-1 for typical Information Plate layout. •

See Figures 1-2 & 1-3 for Serial Number location. •

Figure 1-1 Serial Plate Layout

Figure 1-2 Serial Plate Location (CT Hoods)

Figure 1-3 Serial Plate Location (DD Ventilation)

xxxxxxxxxxx

Unit Serial Number

1-5

General Information CT Hoods and DD Ventilation

MODEL DESCRIPTIONS

This section explains the model numbering system for the CT Hoods and Downdraft models covered in this manual.

EXAMPLE MODEL # ICB CTWH 30 I

PRODUCT TYPE

CTWH COOKTOP (OR CHIMNEY) WALL HOOD

CTEWH COOKTOP (OR CHIMNEY) LOW PROFILE WALL HOOD

CTEIH COOKTOP (OR CHIMNEY) LOW PROFILE ISLAND HOOD

IH ISLAND HOOD

DD DOWN DRAFT

SIZE

30 30 INCH WIDE UNIT

36 36 INCH WIDE UNIT

42 42 INCH WIDE X 27 INCH DEEP

(ONLY ON ISLAND HOOD)

45 45 INCH WIDE UNIT

(ONLY ON DOWN DRAFT)

BLOWER TYPE

I INTERNAL BLOWER

R REMOTE BLOWER

INTERNATIONAL

PRODUCT TYPE

SIZE

BLOWER

1-6

General InformationCT Hoods and DD Ventilation

NOTES

2-1

Installation Information CT Hoods and DD Ventilation

SECTION 2

INSTALLATION

INFORMATION

2-2

Installation InformationCT Hoods and DD Ventilation

30"

(762mm)

18"

(457mm)

21"

(533mm)

12"

(305mm)

/8"

(175mm)

/2"min

(775mm)

/2"max

(1232mm)

/16 " (40)

Figure 2-1 CTWH30 Dimensions

/16"

(900 mm)

18"

(457 mm)

12"

(305 mm)

21"

(533 mm)

/16"min

(829 mm)

/8"max

(1292 mm)

/4"

(235 mm)

/16 " (40)

Figure 2-2 CTWH36 Dimensions

42"

(1067 mm)

27"

(686 mm)

/4"

(235 mm)

18"

(457 mm)

12"

(305 mm)

/16"min

(851 mm)

/16"max

(1197 mm)

/16 " (40)

Figure 2-3 IH4227 Dimensions

MODEL CTWH30

)267("03htdiW llarevO

Overall Height (excluding chimney)

/8" (175)

Overall Height (including chimney)

/2" (775)

Max Height (full extension) 48

/2" (1232)

)335( "12htpeD llarevO

Shipping Weight (shell only) 85 lbs (39 kg)

Dimensions may vary to

–

/8"(3).

MODEL CTWH36

53htdiW llarevO

/16" (900)

Overall Height (excluding chimney) 9

"(235)

Overall Height (including chimney) 32

"(830)

Max Height (full extension) 50

/8" (1292)

)335( "12htpeD llarevO

Shipping Weight (shell only) 100 lbs (45 kg)

Dimensions may vary to

–

/8"(3).

MODEL IH4227

)7601("24htdiW llarevO

Overall Height (excluding chimney)

/4"(235)

Overall Height (including chimney)

/16"(853)

Max Height (full extension) 47

/16" (1195)

Overall Depth 27" (686)

Shipping Weight (shell only) 110 lbs (50 kg)

Dimensions may vary to

–

/8"(3).

CT & ISLAND HOOD OVER-ALL DIMENSIONS

2-3

Installation Information CT Hoods and DD Ventilation

/8"

(511)

/8" (79)

/8"

(276)

/8"

(251)

OVERALL

HEIGHT

30" (762)

OVERALL WIDTH

/4"

(451)

OVERALL DEPTH

/8” (467)

/8” (149)

/8” (740)

/2” (1054)

Figure 2-4 CTEWH30 Dimensions

Figure 2-5 CTEWH36 Dimensions

Figure 2-6 CTEWH45 Dimensions

CTEW HOOD OVER-ALL DIMENSIONS

/8"

(511)

/8" (79)

/8"

(276)

/8"

(251)

OVERALL

HEIGHT

36" (914)

OVERALL WIDTH

/4"

(451)

OVERALL DEPTH

/8” (467)

/8” (149)

/8” (740)

/2” (1054)

/8"

(511)

/8" (79)

/8"

(276)

/8"

(251)

OVERALL

HEIGHT

45" (1143)

OVERALL WIDTH

/4"

(451)

OVERALL DEPTH

/8” (467)

/8” (149)

/8” (740)

/2” (1054)

MODEL CTEWH30I

Overall Width

Height (excluding chimney)

Min Height (including chimney)

Max Height (full extension)

Overall Depth

Shipping Weight

30” (762)

3 1/8” (79)

29 1/8”(740)

41 1/2”(1054)

17 3/4”(451)

53 lbs (24kg)

MODEL CTEWH36(I)

Overall Width

Height (excluding chimney)

Min Height (including chimney)

Max Height (full extension)

Overall Depth

Shipping Weight

CTEWH36

CTEWH36(I)

36” (914)

3 1/8” (79)

29 1/8”(740)

41 1/2”(1054)

17 3/4” (451)

51 lbs (23 kg)

57 lbs (26 kg)

MODEL CTEWH45(I)

Overall Width

Height (excluding chimney)

Min Height (including chimney)

Max Height (full extension)

Overall Depth

Shipping Weight

CTEWH45

CTEWH45I

45” (1143)

3 1/8” (79)

29 1/8” (740)

41 1/2” (1054)

17 3/4” (451)

55 lbs (25 kg)

63 lbs (29 kg)

2-4

Installation InformationCT Hoods and DD Ventilation

Figure 2-7 CTEIH42 Dimensions

CTEI HOOD OVER-ALL DIMENSIONS

/8" (79)

OVERALL

HEIGHT

42" (1067)

OVERALL WIDTH

/8" (549)

OVERALL DEPTH

/2” (394)

/8” (54)

/4” (718)

/2” (1054)

/8”

(308)

/8”

(276)

/8”

(581)

MODEL CTEIH42

Overall Width

Height (excluding chimney)

Min Height (including chimney)

Max Height (full extension)

Overall Depth

Shipping Weight

42” (1067)

3 1/8” (79)

28 1/4” (718)

41 1/2” (1054)

21 5/8” (549)

92 lbs (42 kg)

2-5

Installation Information CT Hoods and DD Ventilation

A C

MINIMUM

FLUE

EXTENSION

Flue Extension

Model Minimum Maximum

CTWH30

" (775) 48

" (1232)

CTWH36

" (830) 50

" (1292)

IH4227

" (853) 47

" (1195)

CTEWH30I

CTEWH36(I)

CTEWH45(I)

CTEIH42I

MINIMUM

FLUE

EXTENSION

A C

sdooH eliforP-woL potkooCsdooH yenmihC potkooC

/8” (740)

/2” (1054)

/8” (740)

/2” (1054)

/8” (740)

/2” (1054)

/4” (718)

/2” (1054)

HOOD PLACEMENT

Wolf cooktop wall and island hoods come with a

telescopic chimney ﬂ ue that allows you to reach ceiling

heights of 8’ (2.4m) to 9’ (2.7m) with a ﬁ nished look.

A ﬂ ue extension to accommodate 10’ (3m) ceilings is

available as a sales accessory for cooktop chimney

hoods only.

Installation of the cooktop wall or island hood should be

24” (610) to 30” 762) from the bottom of the hood to the

countertop.

To determine placement of the wall or island hood, you

must calculate the heights of the telescopic chimney

ﬂ ue. Refer to the chart in Figure 2-8 above for the

minimum and maximum ﬂ ue extension for speciﬁ c

hood.

NOTE: Both sections of the telescopic chimney ﬂ ue

must be installed in order for the chimney to be lifted

for service.

NOTE: If the height of the upper ﬂ ue section is less

than 1/2” (13), you will need to modify the ﬂ ue to afﬁ x

to the ﬂ ue attachment brackets.

Figure 2-8 Hood Placement Dimensions

CALCULATING CHIMNEY FLUE HEIGHT

Measure A (total kitchen height from ﬁ nished ﬂ oor to 1.

ﬁ nished ceiling height).

Measure B (height from ﬁ nished ﬂ oor to countertop). 2.

Determine the desired distance from counter-top to 3.

bottom of hood (C). This dimension must be between

24” (610) and 30” (762).

NOTE: 8’ (2.4m) ceilings may not permit installation of the

wall or island hood at 30” (762) above the countertop.

To calculate the chimney ﬂ ue height (D): D = A – (B 4.

+ C). This dimension must be between the minimum

and maximum ﬂ ue extension for your speciﬁ c hood as

shown in the chart.

HOOD PLACEMENT

2-6

Installation InformationCT Hoods and DD Ventilation

WALL CAP

OR REMOTE BLOWER

COOKTOP

WALL HOOD

DUCTWORK INSTALLATION

THROUGH ROOF

DUCTWORK INSTALLATION

THROUGH WALL

8" (203) ROUND

VERTICAL DISCHARGE

8" (203) ROUND DUCT

CHIMNEY FLUE EXTENSION

TELESCOPIC CHIMNEY FLUE

8" (203) ROUND ELBOW

8" (203) ROUND DUCT

/8" (175) OR 9

/4" (235)

21"

(535)

24" TO 30"

(610–762)

COUNTERTOP

TO BOTTOM OF

VENTILATION HOOD

ROOF CAP OR REMOTE BLOWER –

TRANSITION FROM 8" (203) TO 10" (254) DUCT

REQUIRED FOR REMOTE BLOWER

COUNTERTOP WALL HOODS INSTALLATION

SPECIFICATIONS AND PREPARATIONS FOR

MODELS CTWH30 & CTWH36

A straight, short duct run will allow 1.

the hood to perform more efﬁ ciently.

Limit the number of elbows and tran-

sitions to as few as possible. Long

duct runs, elbows and transitions will

reduce the performance of the hood.

NOTE: All hoods must exhaust to the

outdoors.

NOTE: There is a possibility of noise is-

sues, if a short duct run is coupled with a

remote blower.

Always use metal ducting. Do not 2.

use ﬂ ex ducting.

Wolf recommends installing a back-3.

draft damper in all installations

(included with hood). In cold weather

installations a back-draft damper is

necessary to minimize the back-ﬂ ow

of cold air into the room.

Wolf recommends the hood be in-4.

stalled 24” (610 mm) to 30” (762 mm)

above the cooking surface.

NOTE: Local building codes may require

the use of make-up air. Consult a local

HVAC professional for speciﬁ c require-

ments.

ELECTRICAL REQUIREMENTS

Wolf cooktop wall hoods require a

separate, grounded, 110/120 VAC, 60 Hz

power supply. The service should have its

own 15 amp circuit breaker.

NOTE: You must follow all National

Electrical Code regulations. In addition,

be aware of local codes and ordinances

when installing your service.

TO REDUCE THE RISK OF FIRE, USE ONLY RIGID METAL DUCTWORK.

CT WALL HOOD INSTALLATION CONSIDERATIONS

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, THIS VENTILATION HOOD SHOULD ONLY BE

INSTALLED WITH BLOWERS MANUFACTURED BY WOLF APPLIANCE INC. AND SPECIFIED FOR USE WITH

THESE VENTILATION MODELS.

Figure 2-9 CT Wall Hood Installation Considerations

2-7

Installation Information CT Hoods and DD Ventilation

Figure 2-10 Mounting Bracket Installation

Figure 2-11 Hood Installation

CT WALL HOOD INSTALLATION

INSTALL MOUNTING BRACKETS

Construct wood wall framing that is ﬂ ush with the interior

surface of the wall studs. Make sure that the framing is

centered in the hood installation location, and that the

height of the framing will allow the mounting brackets to

be secured to the framing within the dimension shown in

Figure 2-10.

After the wall surface is ﬁ nished, secure the mounting

brackets to the framing using the dimensions shown.

INSTALL THE HOOD

Hang the hood from the brackets through the rectangular

cut-outs on the back of the hood. The cut-outs are larger

than the brackets to allow for vertical and horizontal

adjustment. (See Figure 2-11)

Keep in mind that the bottom of the hood should be 24”

(610) to 30” (762) above the countertop.

Use height adjustment screws to adjust the hood vertically

and the depth adjustment screws to adjust the hood

horizontally.

Secure the hood with additional mounting screws. If wall

studs or framing are not available in the proper location,

use the drywall anchors provided with the hood.

ELECTRICAL CONNECTIONS

NOTE: This unit should be install by a qualiﬁ ed electrician

in accordance with all applicable national and local codes.

Remove the cover from the rear electrical box knockout 1.

that faces the hood’s discharge collar.

Insert 6” (152) of 120 VAC power cable through the 2.

knockout opening. Secure the cable to the electrical

box with an appropriate connector.

Make electrical connections. Connect black to black, 3.

white to white and green/yellow to green or bare wire.

(See Figure 2-12)

Reinstall the electrical box cover and screws. Make 4.

sure that all wires are secure and that no wires are

pinched between the cover and box.

Green/Yellow to

Green or

Bare Wire

Black to

Black

HOOD FRONT TOP OF HOOD SHELL

Discharge

Collar

120 V AC

Power Cable

Rear

Electrical

Box

White

to White

Figure 2-12 Electrical Connections

TO REDUCE THE RISK OF ELECTRICAL SHOCK,

THIS VENTILATION HOOD MUST BE PROPERLY

GROUNDED.

DUE TO THE WEIGHT OF SOME HOODS, SEVERAL

PEOPLE MAN BE REQUIRED FOR A SAFE AND

PROPER INSTALLATION.

2-8

Installation InformationCT Hoods and DD Ventilation

CT WALL HOOD DUCTWORK INSTALLATION

CONNECT DUCTWORK

Use the screws and wall anchors provided to secure the

upper brackets to the ceiling. Position the upper brackets

based on the dimension of the telescopic chimney ﬂ ue.

(See Figure 2-13)

Use an 8” (203) round metal duct to connect the duct collar

on the hood to the ductwork above. Use duct tape to make

all joints secure and air tight.

Connect the upper section of the telescopic chimney ﬂ ue to

the brackets with the screws provided. (See Figure 2-14)

Nest the bottom of the telescopic chimney ﬂ ue into the

relief in the hood shell.

Figure 2-13 Upper Flue Bracket Installation

Figure 2-14 Securing Inner Flue to Upper Flue Bracket

2-9

Installation Information CT Hoods and DD Ventilation

ISLAND HOOD INSTALLATION SPECIFICATIONS

AND PREPARATION FOR

MODEL IH4227

A straight, short duct run will allow 1.

the hood to perform more efﬁ ciently.

Limit the number of elbows and tran-

sitions to as few as possible. Long

duct runs, elbows and transitions will

reduce the performance of the hood.

NOTE: All hoods must exhaust to the

outdoors.

NOTE: There is a possibility of noise is-

sues, if a short duct run is coupled with a

remote blower.

Always use metal ducting. Do not 2.

use ﬂ ex ducting.

Wolf recommends installing a back-3.

draft damper in all installations

(included with hood). In cold weather

installations a back-draft damper is

necessary to minimize the back-ﬂ ow

of cold air into the room.

Wolf recommends the hood be in-4.

stalled 24” (610 mm) to 30” (762 mm)

above the cooking surface.

NOTE: Local building codes may require

the use of make-up air. Consult a local

HVAC professional for speciﬁ c require-

ments.

ELECTRICAL REQUIREMENTS

Wolf cooktop wall hoods require a

separate, grounded, 110/120 VAC, 60 Hz

power supply. The service should have its

own 15 amp circuit breaker.

NOTE: You must follow all National

Electrical Code regulations. In addition,

be aware of local codes and ordinances

when installing your service.

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

COOKTOP ISLAND HOOD INSTALLATION CONSIDERATIONS

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, THIS VENTILATION HOOD SHOULD ONLY BE

INSTALLED WITH BLOWERS MANUFACTURED BY WOLF APPLIANCE INC. AND SPECIFIED FOR USE WITH

THESE VENTILATION MODELS.

Figure 2-15 Island Hood Installation Considerations

2-10

Installation InformationCT Hoods and DD Ventilation

Figure 2-16 Telescopic Flue Mounting

COOKTOP ISLAND HOOD INSTALLATION

INSTALL SUPPORT SYSTEM

At the island hood installation location, install two-1.

by-four or 3/4”(19) plywood cross framing between

ceiling joists. Refer to the island hood mounting pattern

dimensions. (See Figure 2-16)

Finish the ceiling surface. Be sure to mark the location 2.

of the ceiling joists and cross framing.

Determine the desired orientation of the island hood. 3.

Note that the front designates the control side of the

hood.

Secure the upper half of the support frame to the joists 4.

and cross framing with four screws provided with your

hood. Make sure that the screws are driven into the

center of the joists and framing for maximum strength.

(See Figure 2-17)

Adjust the overall height of the support frame. Loosen 5.

and retighten the screws in the height adjustment slots

as necessary. (See Figure 2-17)

NOTE: The hood height is 11 1/4”(286) from the support

frame attachment point. The bottom of the hood must

be 24” (610)minimum and 30” (762) maximum from the

countertop.

Secure the upper telescopic chimney ﬂ ue section to the 6.

upper support frame. (See Figure 2-18)

Figure 2-18 Upper Chimney Flue Mounting

DUE TO THE WEIGHT OF SOME HOODS, SEVERAL

PEOPLE MAN BE REQUIRED FOR A SAFE AND

PROPER INSTALLATION.

FRAMING MUST BE STRUCTURALLY TIED TOGETHER

AND TIED TO CEILING JOISTS TO PROVIDE ENOUGH

STRENGTH TO SUPPORT WEIGHT OF THE HOOD

AND INTERNAL BLOWER, IF APPLICABLE.

Figure 2-17 Support Frame

2-11

Installation Information CT Hoods and DD Ventilation

MOUNT HOOD TO SUPPORT FRAME

Temporarily secure the lower telescopic chimney 1.

ﬂ ue section over the upper ﬂ ue section.

Mount the hood to the support frame by aligning 2.

the four weld screws on the hood to the four holes

on the support frame. Use four nuts to secure the

hood to the support frame. (See Figure 2-19).

LECTRICAL CONNECTIONS

Remove the cover from the rear electrical box 1.

knockout that faces the hood’s discharge collar.

Insert 6” (152) of 120 VAC power cable through 2.

the knockout opening. Secure the cable to the

electrical box with an appropriate connector.

Make electrical connections. Connect black to 3.

black, white to white and green/yellow to green or

bare wire. (See Figure 2-20)

Reinstall the electrical box cover and screws. Make 4.

sure that all wires are secure and that no wires are

pinched between the cover and box.

Use an 8” (203) round metal duct to connect the 5.

duct collar on the hood to the ductwork above. Use

duct tape to make all joints secure and air tight.

Slide the lower telescopic chimney ﬂ ue section 6.

downward until it ﬁ ts properly around the hood

shell.

Green/Yellow to

Green or

Bare Wire

Black to

Black

HOOD FRONT TOP OF HOOD SHELL

Discharge

Collar

120 V AC

Power Cable

Rear

Electrical

Box

White

to White

TO REDUCE THE RISK OF ELECTRICAL SHOCK,

THIS VENTILATION HOOD MUST BE PROPERLY

GROUNDED.

UNIT SHOULD BE CONNECTED ELECTRICALLY

BY A QUALIFIED ELECTRICIAN IN ACCORDANCE

WITH ALL APPLICABLE NATIONAL AND LOCAL

ELECTRICAL CODES.

Figure 2-20 Electrical Connections

Figure 2-19 Mounting Hood to Support System

2-12

Installation InformationCT Hoods and DD Ventilation

INTERNAL BLOWER INSTALLATION

NOTE: Before turning the power on, make

sure blower control is in the “OFF” posi-

tion. Use wire connectors or wire nuts

approved by UL or C/UL. Refer to installa-

tion instructions provided with each blower

to verify wall or roof cut-outs.

NOTE: Blower options vary with the cook-

ing surface. Use only a Wolf blower with

the cooktop ventilation hood.

NOTE: For mounting and installation of

the internal blower, refer to the speciﬁ c

installation instructions provided with each

blower.

Remove the hood ﬁ lters.1.

Lift the blower into position inside 2.

the hood, the threaded studs on the

blower will slide through the slots pro-

vided in the upper panel.

Use four hex nuts provided with 3.

the blower to fasten the unit to four

threaded studs. (See Figure 2-21)

Plug the blowers’ single power cord 4.

(double for some blowers) into the

receptacle(s) inside the hood. Use the

clip on the hood to keep excess power

cord away from moving parts.

Reinstall the hood ﬁ lters.5.

NOTE: Before turning the power on, make

sure the blower control is in the OFF posi-

tion.

INTERNAL BLOWER INSTALLATION

TO REDUCE THE RISK OF

ELECTRICAL SHOCK, POWER

SHOULD BE TURNED OFF TO

UNIT BEFORE ATTEMPTING THE

FOLLOWING PROCEDURE.

Figure 2-21 Internal Blower Install

Page is loading ...

Wolf CTWH30 Operating instructions

Brand: Wolf

Model: CTWH30

Category: Cookers

Type: Operating instructions

Download PDF

report

Wolf CTWH30 Operating instructions

Wolf CTWH30 Operating instructions

Related papers

Other documents