FMI CHDV37NM Operating instructions

FMI
Brand
FMI
Model
CHDV37NM
Category
Car kits
Type
Operating instructions

This manual is also suitable for

FMI CHDV37NM is a direct-vent fireplace approved for use with the Comfort Glow CD8037 and CD8041 Brick Liner Kit. This accessory kit allows you to customize the appearance of your fireplace to match your decor. The brick liner panels are easy to install and can be removed for cleaning. The kit includes a rear firebrick panel, two retainer brackets, two side firebrick panels, two screws, and instructions. With this kit, you can transform the look of your FMI CHDV37NM fireplace and enjoy the ambiance of a cozy fire.

FMI CHDV37NM is a direct-vent fireplace approved for use with the Comfort Glow CD8037 and CD8041 Brick Liner Kit. This accessory kit allows you to customize the appearance of your fireplace to match your decor. The brick liner panels are easy to install and can be removed for cleaning. The kit includes a rear firebrick panel, two retainer brackets, two side firebrick panels, two screws, and instructions. With this kit, you can transform the look of your FMI CHDV37NM fireplace and enjoy the ambiance of a cozy fire.

1
This brick liner accessory is approved for use in the following
Comfort Glow direct-vent fireplace models: CDV Series and CHDV
Series. Do not use brick liner accessory in any other fireplace
models.
The Brick Liner Kit contains the following:
• 1 - Rear Firebrick Panel • 2 - Retainer Brackets
• 1 - Left Firebrick Panel • 2 - Screws
• 1 - Right Firebrick Panel
If any of these parts are missing or damaged, contact dealer where you
purchased this kit. If they cannot supply original replacement parts,
call DESA International’s Parts Department at 1-800-972-7879 for
information.
WARNING: Turn off, unplug, and let fireplace cool
before installing brick liner. Only a qualified service
person should service and repair fireplace.
NOTICE: You must remove logs before installing
brick liner.
1. Remove the upper louver panel by lifting upward and out (see
Figure 1). Remove screen from CDV Series.
2. Remove the screws from the three tabs at the top of the glass
door. Hold the door securely to keep it from falling forward.
3. Grasp door by both sides and ease it upward off of the lower
bracket. Carefully set aside.
4. Remove ember material and set aside.
5. Remove lava rock from the firebox and set aside.
6. Remove the logs one at a time and set aside. Handle logs with
care.
Figure 2 - Removing Glass Door Assembly
CD8037 and CD8041 Brick Liner Kit
Installation Instructions
Glass Door Assembly
Lower Bracket for
Door Assembly
IMPORTANT:
Read entire instruction sheet before
installing brick liner.
CAUTION: Always handle firebrick panels with
two hands. Do not force firebrick panels into place.
Excessive force will break firebrick panels.
Figure 1 - Removing Top Louver
Top Louver
Figure 4 - Installing Left Side Brick Liner Panels
104891-01
Rev. A
07/98
2701 Industrial Drive, P.O. Box 90004
Bowling Green, KY 42102-9004
Technical Service Department 1-800-323-5190
Parts Department 1-800-972-7879
NOT A UPC
104891 01
CAUTION: Always handle firebrick panels with
two hands. Do not force firebrick panels into place.
Excessive force will break firebrick panels.
Side Brick Panel
Bracket
7. Install rear brick panel first. Rest bottom edge of panel on back
edge of grate (see Figure 3).
CAUTION: Always handle firebrick panels with
two hands. Do not force firebrick panels into place.
Excessive force will break firebrick panels.
Rear Brick Panel
Retainer
Bracket
Figure 3 - Installing Rear Brick Liner Panels and Retainer
Brackets
8. Loosely secure retainer brackets to grate using screws provided.
Brackets will hold rear panel in place.
9. Install left side brick panel by sliding it between the grate and
the side of the firebox (see Figure 4).
CAUTION: Always handle firebrick panels with
two hands. Do not force firebrick panels into place.
Excessive force will break firebrick panels.
10. Slide the left retainer bracket against the left side brick panel.
Tighten the bracket screw. This secures both the left side and
rear brick panels.
11. Install the right brick panel using the same method described
in step 9.
12. Slide the right retainer bracket against the right side brick panel.
Tighten the bracket screw. This secures both the right side and
rear brick panels.
13. Replace the logs, lava rocks and glowing embers by following
the instructions in Installing Logs, Lava Rock and Glowing
Embers section of the fireplace owner’s manual.
14. Replace glass door assembly by carefully placing it on the lower
bracket above the lower louver. Carefully secure the door by
replacing the three screws. Replace screen on CDV Series.
15. Replace the top louver panel.
  • Page 1 1
  • Page 2 2

FMI CHDV37NM Operating instructions

FMI
Brand
FMI
Model
CHDV37NM
Category
Car kits
Type
Operating instructions
This manual is also suitable for

FMI CHDV37NM is a direct-vent fireplace approved for use with the Comfort Glow CD8037 and CD8041 Brick Liner Kit. This accessory kit allows you to customize the appearance of your fireplace to match your decor. The brick liner panels are easy to install and can be removed for cleaning. The kit includes a rear firebrick panel, two retainer brackets, two side firebrick panels, two screws, and instructions. With this kit, you can transform the look of your FMI CHDV37NM fireplace and enjoy the ambiance of a cozy fire.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents