FMI G8007 Operating instructions

Brand: FMI

Model: G8007

Category: Wall & ceiling mounts accessories

Type: Operating instructions

FMI G8007 is a brick liner kit designed for use in VSGF36 series vent-free gas fireplaces. It contains a rear firebrick panel, two side firebrick panels, two retainer brackets, and two screws. The kit is easy to install and can be completed in just a few steps.

The brick liner kit helps to protect the fireplace from heat damage and provides a more realistic look. It is also easy to clean and maintain.

Here are some of the benefits of using the FMI G8007 brick liner kit:

Protects the fireplace from heat damage
Provides a more realistic look
Easy to clean and maintain
Can be installed in just a few steps

The brick liner kit helps to protect the fireplace from heat damage and provides a more realistic look. It is also easy to clean and maintain.

Here are some of the benefits of using the FMI G8007 brick liner kit:

Protects the fireplace from heat damage
Provides a more realistic look
Easy to clean and maintain
Can be installed in just a few steps

IMPORTANT: Read entire instruction sheet before install-

ing brick liner.

This brick liner accessory is approved for use in VSGF36

series vent-free gas ﬁreplace systems. Do not use brick

liner accessory in any other ﬁreplace models.

The Brick Liner Kit contains the following:

• 1 - Rear Firebrick Panel

• 2 - Side Firebrick Panels

• 2 - Retainer Brackets

• 2 - #10 Screws

Tools required:

• Phillips Screwdriver

• 5/16" Hex Socket Wrench or Nut Driver

If any of these parts are missing or damaged, contact dealer where

you purchased this kit. If they cannot supply original replacement

parts, either contact your nearest Parts Central or call DESA Inter

national at 1-866-672-6040 for information.

IMPORTANT:

Always handle ﬁrebrick panels with two hands.

WARNING: Turn off, unplug, and let ﬁreplace cool

before installing brick liner. Only a qualiﬁed service

person should service and repair ﬁreplace.

NOTICE: You must remove log base assembly before

installing brick liner.

1. To remove screen, lift screen up off the screws in front of

ﬁreplace (see Figure 1).

Figure 1 - Removing Fireplace Screen

Screws for

Mounting

Screen

www.desatech.com

G8007 SERIES BRICK LINER KIT

INSTALLATION INSTRUCTIONS

www.desatech.com

114421-01B

2. Remove logs. Remove four screws that attach log base assembly

to ﬁreplace. Carefully lift log base assembly and remove from

ﬁreplace (see Figure 2).

CAUTION: Do not pick up log base assembly by

burners. This may damage burners. Only pick up

base by the grate.

Note: Some installations may require the gas supply line to be

disconnected before removing log assembly. If so, call a quali-

ﬁed service person to disconnect gas supply from ﬁreplace.

WARNING: A qualiﬁed service person must con-

nect and disconnect ﬁreplace to gas supply. Follow

all local codes.

3. With larger bricks at the top, install rear ﬁrebrick panel on back

wall ﬁrst. Rest the bottom edge of ﬁrebrick panel on liner ﬂange.

Stand ﬁrebrick panel straight up against the back of ﬁreplace

(see Figure 3). Note: Side brick liners will hold rear ﬁrebrick

in place.

CAUTION: Always handle ﬁrebrick panels with

two hands. Do not force ﬁrebrick panels into place.

Excessive force will break ﬁrebrick panels.

4. With larger brick at top of panel, slide one side ﬁrebrick panel

behind the retaining edge of ﬁreplace. Gently press the ﬁrebrick

panel back against the side wall (see Figure 4). The bottom edge

of the ﬁrebrick panel will rest on liner ﬂange.

CAUTION: Always handle ﬁrebrick panels with

two hands. Do not force ﬁrebrick panels into place.

Excessive force will break ﬁrebrick panels.

Figure 4 - Placing Side Firebrick Panel Behind Retaining

Edge

Liner Flange

Larger

Brick at

Top of

Panel

Side

Firebrick

Panel

Side Wall

Retaining

Edge

Figure 2 - Removing Log Base Assembly from Fireplace

Figure 3 - Placing Rear Firebrick Panel on Flange in Fireplace

Burners

Screws

Log Base

Assembly

Liner Flange

Larger Brick at

Top of Panel

Rear

Firebrick Panel

Screws

www.desatech.com

114421-01B

6. Secure side ﬁrebrick panel to side wall of ﬁreplace with one

retainer bracket and one screw (see Figure 5).

Note: If there is a screw in the ﬁreplace side walls where you

are to install the retaining bracket, remove screw.

7. Repeat steps 5 and 6 to install other side of ﬁrebrick panel.

8. Put log base assembly back into ﬁreplace. Secure log base as-

sembly with the four screws removed in step 2 (see Figure 2,

page 2).

WARNING: A qualiﬁed service person must con-

nect and disconnect ﬁreplace to gas supply. Follow

all local codes.

WARNING: Test all gas piping and connections

for leaks after installing or servicing. Correct all leaks

at once.

WARNING: Never use an open ﬂame to check for

a leak. Apply a noncorrosive leak detection ﬂuid to

all joints. Bubbles forming show a leak. Correct all

leaks at once.

9. Replace logs. Make sure logs are put in their proper position.

See Installing Logs in the Fireplace Owners Manual.

10. Replace screen (see Figure 1, page 1).

Figure 5 - Securing Side Firebrick Panel to Side Wall of

Fireplace

Retaining

Edge

Screw

Retainer Bracket

114421-01

Rev. B

01/05

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

Technical Service Department 1-866-672-6040

114421 01

NOT A UPC

FMI G8007 Operating instructions

Brand: FMI

Model: G8007

Category: Wall & ceiling mounts accessories

Type: Operating instructions

The brick liner kit helps to protect the fireplace from heat damage and provides a more realistic look. It is also easy to clean and maintain.

Here are some of the benefits of using the FMI G8007 brick liner kit:

Protects the fireplace from heat damage
Provides a more realistic look
Easy to clean and maintain
Can be installed in just a few steps

Download PDF

report

FMI G8007 Operating instructions

FMI G8007 Operating instructions

Related papers

Other documents