Arlington DVFR1W Owner's manual

Type
Owner's manual

This manual is also suitable for

at
www
.aifittings.com
View Video
A
rlington’s recessed non-metallic
IN BOX™ for indoor use allows plasma
and LCD TVs to mount flush against the
wall. Great for furniture or countertop
items like coffee makers or microwave
ovens too!
It’s available in one- or two-gang styles –
in black and white – for power or
low
voltage applications in new construction
or old work.
Using the supplied separator with the
two-gang style allows you to install
one power and one low-voltage device
in the box.
Plugs stay inside the box – without
extending past the wall
For new work;
positioning tabs for 1/2"
wall thickness assure
proper installation on stud
Horizontal or vertical mounting
Textured, paintable trim plate
Accepts single-gang wiring devices
UL Listed. CSA with
g
rounding lug
Catalog UPC/DEI/NAED Description Color Unit Std
Number Mfg. #018997
Indoor IN BOX™ Pkg Pkg
DVFR1W
14330 Single gang White 1 4
DVFR1BL
14329 21.0 cu. in. Black 1 4
DVFR2W
14331 Two gang White 1 4
DVFR2BL
14335
37.0 cu. in. Black 1 4
For flush-to-the-wall mounting of plasma or LCD TVs
N
N
E
E
W
W
more on
reverse
Patented/Other patents pending
One-gang DVFR1W
Kit components (screws not shown)
Indoor IN BOX
Recessed Electrical Box
CSA w/
grounding lug
only
Includes r
ecessed bo
x with trim plate, (one each) duplex and decorator
face plates (two-gang supplied with (1) decorator plate only),
NM cable connector
,
(2) #6 x 1/2" and (2) #8 x 3" installation scr
ews.
Box Trim
Plate
Face Plates
Positioning
Tabs
1 Stauffer Industrial Park
Scranton, P
A 18517
800/233.4717
F
ax 570/562.0646
www
.aifittings.com
Arlington
Separator
Two-gang
DVFR2BL
One-gang
DVFR1W
DVFR2W
R
R
Distributed by
Patented/Other patents pending. DVFR1W 0707REV 1008/30M
© 2007 Arlington Industries, Inc. REV 1008
Mount TVs flush against wall – Plugs stay in the box
Indoor IN BOX
Recessed Electrical Box
New Construction
Old Work
Thread (2) #8 x 3"
screws (supplied)
through the angled
holes in the outer
edge of the box.
Mount box to stud,
using positioning
tabs to allow for
finished wall
(drywall) thickness.
Install N
M cable
connector
(supplied).
Pull wires.
After wall
installation is
complete, wire
in receptacle.
Add trim plate.
(See steps 3 and
4 above.)
Angled
hole
Mount box to stud.
Use positioning tabs to
allow for wall thickness.
Cut hole next to stud.
W
i
re in receptacle.
Attach
paintable
trim
plate.
1 Cut hole next to stud
(3-3/8" x 6" for single-gang,
5
-1/4" x 6" for two-gang).
2 Install NM cable connector
(supplied). Pull wire.
Mount box to stud with (2)
#8 x 3" screws (supplied)
t
hrough the angled holes in the
outer edge of the box. Use posi-
tioning tabs
(see detail below)
to allow for drywall thickness.
3 Wire in receptacle.
(See below for
two-gang combo installation).
4 Attach paintable trim plate with
(2) #6 x 1/2" screws (supplied).
1
2
4
3
1 Stauf
fer Industrial Park
Scranton, PA 18517
800/233.4717
F
ax 570/562.0646
www.aifittings.com
Arlington
(single-gang shown)
Positioning
tabs
Two-gang installation
Use supplied separator...
...for combination power and
low voltage device installations.
Single-gang installation
Receptacle wired into
single-gang box.
CSA w/
grounding lug
only
R
R
  • Page 1 1
  • Page 2 2

Arlington DVFR1W Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI