Bauknecht TK PRO 74A+ Program Chart

Type
Program Chart
1
MACHINE OPERATION
Additional information (including troubleshooting and service) can be found in the individual chapters of
the Instructions for use.
Sort laundry according to
care symbols
Do not tumble dry
Suitable for tumble drying –
at low temperatures
Suitable for tumble drying
Sort laundry by:
Material thickness: whenever there is greater load than the dryer can handle, separate
laundry according to weight (e.g. dry towels and thin underwear separately).
Type of material: cotton (linen); synthetic textiles (easy care).
Degree of drying: cupboard dry, iron dry etc.
Do not tumble dry: nylon stockings, delicate embroidery, fabrics with metallic decorations.
Preparing laundry
Check that all fastenings are closed and that pockets are empty.
Please ensure that there are no cigarette lighters in the laundry.
Turn laundry inside out.
Loading dryer
Place laundry loosely in the drum to achieve equal drying throughout.
Then close the door.
Selecting programme
Select the drying programme required by turning the programme selector knob (for
information, refer to programme table).
If you do not start the programme soon after having made your choice, the dryer will switch
off after a few minutes.
To switch the dryer on again turn the programme selector knob to “Off” (“0”) and afterwards
to the desired programme.
Selecting options
(if available)
Select the option required by pressing the corresponding button.
The indicator lamp above the relevant button lights up to confirm your selection.
A fast blinking lamp indicates a wrong selection is made (incompatible options).
Press the button again to cancel the option.
Starting dryer
The drying programme is started by pressing the “Start (Pause)” button.
The relevant indicator lamp lights up.
Changing programme selection: If the programme selected is changed during drying, the
dryer stops.
The “Start (Pause)” indicator lamp flashes.
To operate the new programme, press the “Start (Pause)” button again.
Interrupting programme: To interrupt a drying cycle, press the “Start (Pause)” button and
open the door.
Wait at least 5 minutes, to allow the laundry to cool down, before you unload the dryer.
For your safety the drying cycle stops automatically if you open the door.
To restart, after door opening, close the door and press the “Start (Pause)” button again.
Warning: Never stop a tumble dryer before the end of the drying cycle, unless all items are
quickly removed and spread out so that the heat is dissipated.
Programme end –
unloading dryer
The final part of a drying cycle occurs without heat (cool down cycle) to ensure that the items
reach a lower temperature to avoid wrinkling.
End: Take the laundry out of the dryer.
The drying process is complete.
Anticrease: If the laundry is not removed at the end of the drying cycle, an automatic anti-
crease cycle will operate for maximum 15 min (by choosing the option “Anticrease” this time
can be extended up to 12 hours).
The drum rotates to prevent the laundry from creasing.
After the end of the “Anticrease” the dryer will switch off after a short time, to save energy.
Switching dryer off
Set the programme selector knob to “Off” (“0”).
Cleaning the door filter after every cycle: open door, pull door filter up and out of machine and open it. Brush lint using a soft
brush or your fingertips. Close door filter and push firmly back into place.
Emptying water container: pull container out by the handle and empty. Replace the container when empty by pushing it
completely back into place.
Please note: Only use additives/plastic items specified as dryer safe and rinse items that have been treated with stain remover
thoroughly in plenty of water before drying. Never dry rubber objects or objects stained with vegetable oils in the dryer.
The Manufacturer is not liable for any damage to laundry resulting from inadequate or incorrect fabric care instructions which
have been provided with the garment or article.
Power consumption: in off-mode 0.11 W / in left on-mode 0.11 W
2
Overview of programmes Options
Approximate
drying times
(in minutes)
Type of textile
Programmes / Drying levels
Fabrics
Gentle
Schonen
Anti-
crease
Knitter-
schutz
Dryness
adjustment
Trocken-
grad
Pause
Start
(Pause)
Key lock
Kinder-
sicherung
Reset
Löschen
Dum
light
Licht
Finish
in
Fertig
in
Very
wet load Wet load
Cotton
Extratrocken Extra dry
Multi-layered, thick laundry such as:
terry towels, terry towelling bath robes.
Cotton or linen hot wash /
coloured laundry
Koch-/Bunt-
wäsche
Max. 7.0 kg
X X X X X X X X 190 140
Schranktrocken plus Cupboard dry +
Terry towels, dry towels, bed linen,
underwear
X X X X X X X X 165 125
Schranktrocken Cupboard dry*
Similar types of laundry which do not
require ironing such as: dry towels, bed
linen, underwear, baby clothes, T-shirts,
cotton socks.
X X X X X X X X 155 110
Bügeltrocken Iron dry*
Laundry which requires ironing such as:
bed and table linen, dry towels, T-shirts,
polo shirts, work clothes.
X X X X X X X X 135 90
Synthetic
Extratrocken Extra dry
Laundry with thick, multi-layered areas
such as: bed and table linen, track suits,
anoraks, blankets.
Synthetic, mixed fibre or
cotton easy care (ironing not
required) laundry
Pflegeleicht
Max. 3.5 kg
X X X X X X X X 80 70
Schranktrocken Cupboard dry*
Laundry which does not require ironing
such as: shirts, blouses, T-shirts,
sportsware.
X X X X X X X X 65 60
Bügeltrocken Iron dry
Laundry which requires ironing such as:
trousers, dresses, skirts, shirts, blouses.
X X X X X X X X 55 50
Special programmes
Supersanft
Delicate plus
Low drying intensity for delicates and
items such as: trousers, dresses, shirts,
blouses.
Laundry made from synthetic
fibres such as polyamide,
nylon, polyacrylic, etc.
2.5 kg
X X X X X X X X 80 60
Mix
Mixed load
T-shirts, blouses, towels, underwear,
sportswear.
Cotton – synthetic blend
2.0 kg
X X X X X X X X 70 50
Seide
Silk Blouses, shirts and T-shirts.
Textiles made of silk
2.5 kg
X X X X X X X X 65 50
Wolle
Wool
Only for drying wool with specific label
from Woolmark: TOTAL EASY CARE
WOOL
Textiles made of wool
1.0 kg
X X X X X X 60
XXL
Down Sleeping bags, trousers, vests.
Laundry that contains downs
3.0 kg
X X X X X X 120 120
Airing
Laundry is aired, refreshed and loosen up
for 30 minutes without heating.
All textiles.
Lüften
– – – X X X X – – –
Drying
times
Completes drying All textiles.
Zeitprogramme
10’ – 180’
X X X X X X 10’ 180’
*Test programmes according to EN61121.
3
HOW TO PROCEED IF…
...you want to check the dryer yourself first: (If your machine is not functioning correctly, please check the
following points before calling the customer service – also refer to relevant chapter in the Instructions for use)
Drying takes too long /
Laundry is not dry
enough
Has the correct drying programme been selected?
Has the cycle been interrupted (door opening, full water container)?
Was the inserted laundry too wet (washing machine spin speed less
than 1000 rpm)?
Is the door filter dirty (filter indicator light on)?
Is the bottom filter dirty (for more information, refer to the Instructions
for use)?
Is the room temperature too high?
Is the “End” and “Anticrease” indicator lamp lighting up?
The drying cycle is complete and the laundry can be taken out.
If the drying result does not meet your expectation, select a more dry
programme or use the dryness adjustment option (if available) to
optimize the drying result.
The dryer does not
operate (after a power
failure, always press
the “Start (Pause)”
button)
Is the plug properly inserted into the mains electricity socket?
Is there a power failure?
Has the fuse blown?
Is the door properly closed?
Has a drying programme been selected?
Has the “Start (Pause)” button been pressed shortly after a
programme is selected? (If not, the dryer will switch off.)
Has the start delay option been selected?
Is the dryer overloaded? Please remove a part of the load.
Door filter, water
container or bottom
filter indicator lamp on
Is the door filter clean?
Is the water container empty?
Has the water container been inserted correctly?
Is the bottom filter clean and inserted correctly?
Water droplets
underneath the dryer
Has the bottom filter been inserted correctly?
Have all lint on the bottom filter seal and the door seal been wiped
away?
Has the water container been inserted correctly?
If the direct drain connection is used, is it tight?
Is the dryer leveled?
...you want to care of and clean your dryer:
Clean the door filter at
the end of every cycle
Brush lint using a soft brush or your fingertips.
Close the filter.
Push the filter back into place.
Empty the water
container at the end of
every drying cycle
Pull the handle to remove the water container.
Empty the water container.
Replace the water container when empty by pushing it completely
back into place.
Clean the bottom filter
every fifth cycle
Clean the bottom filter under running water.
Remove all fluffs from the seals.
Clean the bottom filter housing (for further information see chapter
“Cleaning the Bottom Filter” in the Instructions for use).
See the Instruction for use for further information how to clean the
bottom filter.
4
FAILURE CODES
In case of a malfunction of the dryer, one the following failure codes could be displayed.
Depending on the model of your dryer, the failure can be displayed in letters or by different blinking lamps.
Failure
code
Lamps failure code
Check needed by customer before
Service call
F01
Please call the After-Sales-Service.
F02
Please call the After-Sales-Service.
F03
Please call the After-Sales-Service.
F04
Please call the After-Sales-Service.
F05
Turn OFF the dryer.
Unplug the dryer.
Assure that the ambient temperature is
between 5°C and 35°C.
Wait for 1 hour.
Plug the dryer again and restart the dryer.
If the failure occurs again, please call the
After-Sales-Service.
F06
F07
F10 – F24
Turn OFF the dryer.
Unplug the dryer.
Wait for 30 minutes.
Plug the dryer again and restart the dryer.
If the failure occurs again, please call the
After-Sales-Service.
Start lamp is blinking 2 times per second when it is pressed
Assure that the door is correctly closed and
bottom filter correctly positioned.
Bottom filter lamp is blinking or Door filter lamp is blinking
2 times per second when the Start button is pressed
Assure that the bottom filter is correctly
positioned.
Star
t
(Pause
Türfilte
r
Wärme
-
tauscherfilte
r
Wäss
e
behält
e
leeren
B
e
Progra
m
The dryin
g
this knob.
The “Star
t
)
“Start (
P
The dryin
g
this button
The indica
r
Door Fi
l
The indica
filter need
s
Clean the
drying cy
c
-
r
Bottom
This indic
a
bottom filt
e
This indic
a
bottom filt
e
Please ta
k
correctly i
n
engaged.
er
-
er
Water c
o
The indica
container
n
The dryin
g
Empty the
programm
e
Empty th
e
drying cy
c
e
fore using th
e
Q
I
n
m
me select
o
g
programme is
t
(Pause)” indi
c
P
ause)” but
t
g
programme is
.
tor lamp lights
u
l
te
r
tor lamp lights
u
s
to be cleaned
.
door filter at t
h
c
le.
Filter
a
tor lamp lights
e
r needs to be
c
a
tor lamp is blin
k
e
r is not correct
l
k
e care that the
n
serted and the
o
ntaine
r
tor lamp lights
u
n
eeds to be em
g
cycle is autom
container and
r
e
.
e
water contai
n
c
le
e
machine, ple
a
uick R
e
n
dicator
l
o
r knob
selected by tur
n
c
ator lamp flash
t
on
started by pres
s
u
p.
u
p when the do
o
.
h
e end of ever
y
u
p when the
c
leaned.
k
ing, when the
l
y positioned.
bottom filter is
handle is fully
u
p when the wa
p
tied.
atically interrup
t
r
estart the dryin
n
er after every
5
a
se also read t
eferen
lamps a
n
n
ing
es.
sing
o
r
y
a
ter
ted.
g
h
e instruction
s
ce Gui
n
d Opti
o
R
D
e
d
e
Af
c
o
a
n
T
h
v
a
d
r
T
h
c
a
T
h
E
c
T
h
fe
e
th
e
As
to
E
e
x
T
h
c
o
pr
o
c
o
T
h
m
o
th
e
F
o
e
n
tu
m
E
n
T
h
Pl
e
O
v
T
h
c
o
th
e
E
s
for use caref
u
de
o
ns
R
emaining ti
m
e
pending on th
e
e
fault drying tim
e
t
er start of cycl
e
o
rrected depen
d
n
d moisture of t
h
h
e drying time
a
lue which will
r
ying cycle.
h
e flashing line
s
a
lculation is run
n
h
e remaining ti
m
c
o Monito
r
h
e “Eco monit
o
e
dback about t
h
e
humidity stea
r
s
soon as you t
u
any humidity s
t
E
co monitor” l
a
x
pected energy
h
e three indicat
o
o
nsumption: the
o
gramme settin
o
nsume, the les
s
h
is depends on
t
o
isture and opti
o
e
size of the lo
a
o
r that reason, t
h
n
ergy consumpt
m
ble dryer det
e
n
d
h
e drying progr
a
e
ase unload th
e
v
erdry prote
c
h
e indicator ligh
t
o
ntrolled progra
m
e
activated prot
e
E
coMonitor
ully!
m
e” display
e
programme s
e
e is displayed.
e
the time displ
a
d
ing on the volu
h
e laundry.
specified is a
c
be updated d
u
s
indicate that t
h
n
ing.
m
e will be upda
t
o
r” gives you a
h
e energy cons
u
red programm
e
u
rn the progra
m
t
eared program
a
mps will indica
consumption.
o
rs show the d
e
less energy yo
n
g is forecasted
s
indicators will
the programm
e
ons selected,
a
a
d.
he forecasted
d
t
ion may adapt
w
e
cts the load si
z
a
mme is finishe
d
e
drye
r
.
c
tion
ts up when a h
u
m
me is selecte
d
t
ection function.
e
lected a
a
yed is
m
e, type
c
alculated
u
ring the
h
e
t
ed.
rough
u
mption of
s.
m
me selector
me, the
t
e the
e
gree of
ur
to
light up.
e
, initial
nd also on
d
egree of
w
hen the
z
e.
d
.
u
midity
d
, to indicate
6
Trocken-
grad
Dryness level
By selecting this option you can adjust the
dryness level of the laundry.
A
fter the selection of the desired programme
you can choose the dryness level by
pressing the button.
Pressing 1 time you select a more dry level
or
Pressing 2 times you select a less dry level
or
Pressing 3 times you select again normal dry
level
.
Löschen
Reset
During the selection phase of the
programme, pressing this button will switch
off all settings of selected options.
During running drying cycle the pressing of
the button will stop the cycle and set the
dryer back in selection mode.
The button needs to be pressed for
3 seconds.
Kinder-
sicherung
Key lock
For child protection reasons, this option can
be used to lock all functions of the user
interface.
To activate this option, the button needs to
be pressed for 3 seconds, until the “key”
symbol at the display appears.
To deactivate this option, press the button
until the “key” symbol disappears.
The key lock function is still active even
when the selector knob is turned to “off”
position or the door is opened.
The function has to be deactivated.
Zeitpro-
gramme
Dry time adjustment
Turn the programme selector knob to
“Drying Time” position.
Press the button “Drying time” to select the
duration of cycle in ten minutes steps up to
180 minutes.
Schonen
Gentle
Selecting this option will reduce the drying
temperature.
This option cannot be selected when the
option “Rapid” is selected.
Knitter-
schutz
Anticrease
This option can be chosen to reduce
wrinkling, when the laundry is not unloaded
directly after end of the cycle.
The drum turns from time to time for
maximum 12 hours.
It can be interrupted at any time by switching
off the dryer.
This option deactivates the “Buzzer”
function, if it is activated.
Licht
Drumlight
The drum light can be switched on and off.
Fertig
in
Finish in
With this function you can postpone your
programme to complete at a later time: press
the button to select in how many hours the
programme shall be finished.
Thus, it allows you to have your laundry
ready at a particular time and to profit
from more favourable energy rates
during the night, for example.
The “Finish in function can be selected
in full hour time segments (1 to 24 h).
When you press the button, the shortest
possible time will be displayed; keep on
pressing the button to loop through all
the available times.
To remove it again, set the index of the
programme selector knob to the “Off”
“(0)” position.
When you have selected the desired
“Finish in” time, press “Start” – the
countdown will begin.
During the countdown, you can still
modify the option setting (select or
deselect options).
Sometimes the programme may finish
before the selected “Finish in” time has
expired (e.g. for small loads).
In this case, the dryer will tumble the
laundry regularly to keep it fresh, until the
selected “Finish in” time has expired.
During tumbling, the display will show an
animation.
The tumbling phase can be stopped at
any time either by pressing any button,
by rotating the programme selector or by
opening the door.
Fert ig
in
5019 400 00286
(Subject to technical modifications)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Bauknecht TK PRO 74A+ Program Chart

Type
Program Chart

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI