Whirlpool AKM 481 IX Program Chart

Brand: Whirlpool

Model: AKM 481 IX

Type: Program Chart

AKM 481 PRODUCT DESCRIPTION SHEET

5019 319 66051

Whirlpool is a registered trademark of Whirlpool USA

Operation of burners with safety

device and electric ignition

To light one of the burners:

 Press the relative knob and turn it anti-

clockwise to the large flame and star

setting .

 At the same time, hold the knob down until

the burner ignites.

 After the burner has ignited, keep the knob

pressed for about 10 seconds.

 Release the knob.

If the burner does not ignite, repeat the operation.

Note:



Should particular local conditions of the

delivered gas make the ignition of the burner

difficult, it is advisable to repeat the

operation with the knob turned to the small

flame setting .



The burner safety device shuts off the gas

supply to the burner if the flame goes out

accidentally (because of a sudden draught,

an interruption in the gas delivery, boiling

over of liquids, etc.).

Removable grids

Semi-rapid burners

Triple crown burner

Auxiliary burner

Right rear semi-rapid

burner control knob

Left rear semi-rapid

burner control knob

Triple crown burner

control knob

Front auxiliary burner

control knob

Front semi-rapid burner

control knob

Symbols

Shaded

circle

Tap closed

Large

flame

and star

Maximum opening/delivery

and electric ignition

Small

flame

Minimum opening or

reduced delivery

3gb66051.fm Page 1 Wednesday, March 17, 2004 12:37 PM

DIMENSIONS OF COOKING HOB AND WORKTOP (mm)

Note: In case of installation of a hood above the cooking hob, please refer to the hood

instructions for the correct distance.

Important:

Installation of this product requires masonry and/or carpentry work. Therefore, it must

be carried out by a competent technician. The appliance may be installed on various

surfaces, such as brickwork, metal, solid wood and plastic laminated wood, provided

they are made of heat resistant materials (T 90°C).

Installation of flush fitting model

Provide an opening in the worktop in accordance with the dimensions shown in the figure, leaving a

minimum clearance of 50 mm from the rear edge. The lower face of the hob must be accessible after

installation.

The appliance can be positioned against walls which are higher than the worktop, leaving the minimum

clearance (

A

) shown in the figure, in order to avoid damages caused by excessive heat. Make sure there is

a minimum vertical clearance of

750 mm

between the burner flames and an overhead shelf (fig.1).

This type of appliance requires milling a 2.5 mm deep recess on the worktop, following the measures

indicated in

figure 2

. Before fitting the hob, it is necessary to apply the sealing tape

E

supplied with it

to the full length of the milled surface

(fig. 3)

. Then place the hob on the milled surface and secure it to

the support structure using screws and brackets

C

D

(depending on the thickness of the worktop),

until it is flush to the worktop.

Brackets

C

should be used to secure the hob to a top which is 20 to 30 mm thick, whereas brackets

D

should be used for a worktop 30 to 50 mm thick.

Important:

 tighten the brackets that secure the hob to the worktop by hand. Do not overtighten.



if the worktop is made of wood or similar materials, the milled surface must be protected with

primer (protective paint) before applying seal E.

Fig.1

Fig.2

Fig.3

3gb66051.fm Page 2 Wednesday, March 17, 2004 12:37 PM

INJECTORS TABLE CATEGORY II2H3+

Type of gas used

Type of

burner

Injector

marking

Rated heat

capacity

Pcs-kW

Rated

consumption

Reduced

heat

capacity

Pcs-kW

Gas pressure

min. rat. max.

NATURAL GAS

(Methane) G20

Triple crown

semi-rapid

auxiliary

133

3.50

1.75

1.05

333 l/h

167 l/h

100 l/h

1.50

0.45

0.35

17 20 25

LIQUID PETROLEUM

GAS

(Butane) G30

Triple crown

semi-rapid

auxiliary

3.50

1.75

1.05

254 g/h

127 g/h

76 g/h

1.60

0.45

0.35

20 28-30 35

LIQUID PETROLEUM

GAS

(Propane) G31

Triple crown

semi-rapid

auxiliary

3.50

1.75

1.05

250 g/h

125 g/h

75 g/h

1.60

0.45

0.35

25 37 45

Type of gas used

Appliance

model

Total rated heat

capacity

Pcs-kW

Total rated

consumption

Air required

for burning

G20 20 mbar 5 gas 9.80 933 l/h 19.6

G30 28-30 mbar 5 gas 9.80 712 g/h 19.6

G31 37 mbar 5 gas 9.80 701 g/h 19.6

3gb66051.fm Page 3 Wednesday, March 17, 2004 12:37 PM

3gb66051.fm Page 4 Wednesday, March 17, 2004 12:37 PM

Whirlpool AKM 481 IX Program Chart

Whirlpool AKM 481 IX Program Chart

Whirlpool AKM 481 IX Program Chart

Related papers

Other documents