HySecurity StrongArm M30/M50 Second Traffic Light Installation guide

HySecurity
Brand
HySecurity
Model
StrongArm M30/M50 Second Traffic Light
Type
Installation guide
Page 1
www.hysecurity.com © 2022 P/N MX002608, MX002646, MX002728, MX002849, MX4171 D0486 Rev F
Installation Instructions
MX002608, MX002646, MX002728, MX002849, MX4171
Adding Second Trac Light (M30/M50)
The StrongArm Crash Trafc Light Option can be mounted in four
different locations: two mounts exist on the Pivot post and two mounts
exist on the Catch post. If you attach the trafc light to the Catch post,
you will need:
yTo drill through the Entrapment shield (see illustration)
yTo feed additional wire through conduit to the Pivot post’s Smart Touch Controller
(STC) board.
Tools Needed
yPipe wrench or large Channel Locks, Electrical tape, Needle-nose pliers
yPhillips-head screwdriver, 1/2, 9/16 & 7/16-inch box end & socket wrenches
y1/2-inch drill bit
NOTE: Catch post mount requires additional wire.
CAUTION
Turn OFF power to the StrongArm operator and take the necessary precautions to avoid electri-
cal shock.
Assemble the Trac Light
Refer to the illustration, while you take the following steps:
1. Open the trafc light access panels and tape the spade ends of
the wires.
2. Feed the wire through pipe.
3. Secure the pipe inside the trafc light access panel using the large
locknuts and washers provided. Refer to the illustration.
4. Remove the Pivot post’s front panel. To access the trafc light
mounting holes, use a 7/16-inch socket and remove the cover
plate from the chassis.
5. Feed wires through chassis and secure trafc light assembly.
Wire
Elbow
Bracket
Feed wires
through hole in
chassis. Secure
trac light
assembly.
5
Trac light
4
StrongArm M30
Pivot & Catch Posts
shown
Front Panel
Pivot post
Use ½-inch bit
to drill 3 holes
through shield
& mount trac
light.
Entrapment
shield
C/L
Dist: 4.125 in
(11 cm)
Dist: 2.06 in
(5 cm)
Drill holes
through shield
Clearance hole
for wire
Assemble the Trafc Light per
the illustrations. Two different
pole mounts exist.
MX002849
MX002849 MX002608
MX002608
a. Open Trafc Light
access panels.
b. Unwrap and feed wires
through pipe.
c. Secure pipe to
Trafc Light with
threaded lock nuts.
MX4170 (x4)
MX000699 (x2)
MX000706 (x4)
MX000698 (x2)
MX002664 (x2)
MX000711 (x2)
Four
bolt
mount
Tri-stud washer
with fasteners
(3 washers & nuts)
Two
bolt
mount
Yellow
Aluminum
3
2
1
Page 2
www.hysecurity.com © 2022 P/N MX002608, MX002646, MX002728, MX002849, MX4171 D0486 Rev F
Assemble the Trac Light, continued
To connect the trafc light wires to the Smart Touch Controller (STC)
board, take the following steps:
6. Route the wire to the STC. Plug the bundled wires MX002646
(provided in the kit) into their matching wires coming from the STC
and Power Module. Match the wire color and connect female to
male (or vice versa).
NOTE: You may need to unplug the wires from the existing trafc light and
reattach them to the wire harness.
7. Plug the opposite ends of the wires into the matching wire harness
coming from the trafc lights. One set of black, white, and red wires
for one trafc light. The other set of black, white, and red wires into
the other set of wires for the other trafc light.
8. Neatly arrange wires and making sure all are securely fastened.
9. Turn the main power to the operator ON and cycle the operator
open and close to test that the trafc lights are working properly.
Maintenance
For maintenance or troubleshooting issues, refer to the operator’s
product manual. If you do not have a copy of the manual, it is available
on the HySecurity website at www.hysecurity.com.
Technical Support
For Technical Support, call your installer or authorized HySecurity
distributor. Obtain the serial number of your operator before calling. For
the name of a distributor near you, call HySecurity at 800-321-9947.
For information about HySecurity training for installers, maintenance
personnel and end users, refer to the company website at www.
hysecurity.com.
Reset
Smart Touch Controller
Security
Hy ®
Reset
Smart T
T
T
T
T
T
T
T
T
T
T
T
T
ouch Co
o
uch
uch
hC
c
ch Co
uc
uch C
C
uch Co
ouch
uch C
ouch Co
h
ouch C
o
ouch Co
ch C
ouch Co
h
hC
ouch Co
ouch Co
o
uch C
c
c
h
h
ouch Co
C
C
C
C
uch C
Co
o
ouch Co
o
ch Co
o
o
o
c
h C
h Co
ch
h C
o
o
ouch Co
h C
h
h
C
C
u
u
C
o
n
ntrolle
n
nt
t
t
t
ntr
t
t
nt
n
t
nt
t
t
r
ntr
t
nt
n
ntr
t
t
r
r
t
t
t
r
Security
curity
urit
ri
it
y
Securit
ty
y
y
y
y
y
y
y
Hy
H
Hy
y
y
H
H
y
y
H
H
y
y
y
S
S
®
Conduit
between posts
Wire es available
for securing wires.
Disconnect single
trac light wires and
reaach wire bundle
for the two trac
lights.
Wire bundle: MX002646
Connect the wire harness to the single
black, white, and red wires coming o
the STC board or power module. Make
sure the wires match to their same
colored counterparts.
Bundle the opposite ends into
two sets of one black, one
white, and one red wire and
connect them to the matching
wires coming from the trac
lights.
Smart Touch Controller
7
8
6
Power Supply
Terminal Blocks
NOTE: Only trac light wiring shown.
(+24V)
(-24V)
BLACK
TERMINAL
BLOCKS
RED
T
ERMINAL
BLOCKS
  • Page 1 1
  • Page 2 2

HySecurity StrongArm M30/M50 Second Traffic Light Installation guide

HySecurity
Brand
HySecurity
Model
StrongArm M30/M50 Second Traffic Light
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents