2. HySecurity
  3. StrongArm M30/M50 Mag Lock

HySecurity StrongArm M30/M50 Mag Lock Installation guide

  • Hello, I'm your chat assistant. I have analyzed the provided document, which is the installation instructions for the HySecurity StrongArm CRASH Mag Lock MX3009. This document details the steps for mounting, adjusting, and wiring the Mag Lock. It includes information about the strike plate, upper catch pin, and how to connect it to the controller. I'm ready to answer your questions about the installation process and operation of the device.
  • How should I adjust the lock assembly height?
    What should I do with the strike plate's upper catch pin clamp?
    How do I mount the Mag Lock to the catch post?
Page 1
www.hysecurity.com © 2019 P/N MX3009 D0599 Rev B
Installation Instructions
MX3009
StrongArm CRASH Mag Lock
Adjust the height of lock assembly to
allow the strike to rest on the magnet
after compressing the bumper. This will
minimize noise while allowing lock to hold
consistently.
Strike plate
Magnet
Rubber
bushing for wires
Use a hex key to
remove four screws
and separate the
strike plate’s upper
catch pin clamp.
Remove the
Entrapment Shield.
Remove the two shaft collars from
the upper catch pin.
Attach the strike plate to the upper
catch pin.
Secure the strike plate clamp.
Mount the Mag Lock to
the catch post using the
two bolts, four washers and
two lock nuts, provided.
Remove the fasteners and
base plate.
Sha collar
Upper catch pin
Page 2
www.hysecurity.com © 2019 P/N MX3009 D0599 Rev B
Wiring the Mag Lock
Connect wires from the Mag Lock to the STC board and +24V on the power
supply board.
STOP BUTTON
OPEN BUTTON
CLOSE BUTTON
REMOTE OPEN AND
RADIO CONTROL
OPEN/CLOSE
1
OPEN PARTIAL
INTERLOCK OPEN
TIME CLOCK OPEN
FREE EXIT DETECTOR
DISABLE EXIT DETECTOR
DISABLE CLOSE TIMER
INSIDE OBSTRUCTION
VEHICLE DETECTOR
OUTSIDE OBSTRUCTION
VEHICLE DETECTOR
SHADOW/RESET
VEHICLE DETECTOR
SENSOR 1
SENSOR COMMON
SENSOR COMMON
DO NOT USE
SENSOR 2
DO NOT USE
SENSOR 3
DO NOT USE
CHARGER
AC LOSS
LOCK INTERLOCK
EMERG CLOSE
FIRE DEPT OPEN
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
Smart Touch Controller
LIMIT DUAL GATE RADIO OPTIONS
DRIVE POWER RS485
MOTOR USER 1 USER 2
USER 3
VEHICLE DETECTORVEHICLE DETECTORVEHICLE DETECTOR
STOP/BUZZER
FREE
EXIT
INSIDE
OBSTR
OUTSIDE
OBSTR
SHADOW
RESET
WIEGAND
HySecurity
COM
NO
MX000585
VERSION
S/N
RS232
DISPLAY
VEHICLE DETECTOR
COM COMA B
RPM
COMOPEN EDGE+24V +24V
STAT US
LED
Power Connector
Mag Lock
connections
NO
NC NO
NC
COM
COM
+
-
Power Supply Terminal Blocks
(+24V)
(-24V)
BLACK
TERMINAL
BLOCKS
RED
TERMINAL
BLOCKS
R2 6
RELAY 2 LOGIC
Technical Support
For Technical Support, call your installer or authorized HySecurity distributor.
Obtain the serial number of your operator before calling. For the name of a
distributor near you, call HySecurity at 800-321-9947 or refer to the company
website at www.hysecurity.com.
Upper catch pin
(barrier arm not shown)
Use pig tails to crimp and
connect wires.
Replace base plate and
secure fasteners.
Conguring the Operator
Access the Installer Menu, R2 RELAY LOGIC and make
sure that the user relay is set at its default setting of 6,
Gate Lock Output.
If you need more information, refer to the gate operator’s
product manual, User Relays - Programming Procedure.
Wiring Diagram
NOTE: Wiring returns
through conduit to
Pivot Post and connects
to power supply and
STC boards.
/