Havis C-VS-1000-TAH Installation guide

Brand: Havis

Model: C-VS-1000-TAH

Type: Installation guide

Havis C-VS-1000-TAH

The Havis C-VS-1000-TAH is a vehicle-specific console designed for the 2007-2014 Chevy/GMC Suburban/Tahoe/Yukon XL/Yukon/Avalanche. This console provides a convenient and organized way to mount and access switches, control heads, and accessories in your vehicle.

The C-VS-1000-TAH is made from high-quality materials and is designed to withstand the rigors of everyday use. It features a durable construction and a sleek, professional appearance that will complement any vehicle's interior.

The C-VS-1000-TAH is easy to install and can be completed in just a few hours.

Havis C-VS-1000-TAH

The C-VS-1000-TAH is easy to install and can be completed in just a few hours.

INSTALL INSTRUCTIONS C-VS-1000-TAH

VEHICLE SPECIFIC CONSOLE

2007-2014 CHEVY/GMC SUBURBAN/TAHOE/YUKON XL/

YUKON/AVALANCHE

TOOLS REQUIRED:

Ratcheting wrench

Metric/Standard Socket Set

Standard Wrench Set

Power drill w/ 1/8” drill bit (optional)

Screwdriver set

T-20 torx bit

HARDWARE:

QTY DESCRIPTION PART #

1 OEM switch bracket CM001800-3

4 ¼-20 Serrated nut GSM30023

2 ¼-20 x ¾” Hex bolt GSM33001

2 #10 x ¾” Sheet metal screw GSM33195

1 Torx screw hardware kit C-HK-1

C-VS-1000-TAH

OEM switch bracket

CM001800-3

This will hold the OEM

three or four switch cluster

Switch cutout filler plate

CM001800-4

Supplied lighter plugs

C-VS-1000-TAH_INST_12-10 rev 11-13

Remove factory cup holder/accessory

pocket from console

CAREFULLY separate trim bezel

from dashboard

If your console is not equipped with

adjustable pedal, tow package, and power

brake switches proceed to step #13

Note:

View of OEM / Factory full-length console.

NOTE:

The mount bolts for the OEM center

console may need to be loosened in order

to properly readjust the position so it will

accept the New C-VS-1000-TAH console.

Tighten OEM bolts when done.

C-VS-1000-TAH_INST_12-10 rev 11-13

Using a flat head screwdriver

concentrate pressure on or around

the trim bezels “J” clips

Remove entire bezel and put aside. Remove factory trim screws to

remove the lower switch panel on

dashboard

Install switch box into

C-VS-1000-TAH (if necessary)

View of factory console at this time Attach switch box to console

using T-20 torx screws. Do not

over tighten screws. This will

cause the switches to “stick” in

the ON position.

#12

#11 #10

Unplug switch and set aside for

later install

Remove factory switch box from

trim panel Using a small flat head

screwdriver, unclip fastener

#7 #9

NOTE:

The mount bolts for the OEM center

console may need to be loosened in

order to properly readjust the

position so it will accept the New C-

VS-1000-TAH console.

Tighten OEM bolts when done.

NOTE: Wrapping the switch

assembly with electrical tape

works well for the screws to

push against in step #12.

C-VS-1000-TAH_INST_12-10 rev 11-13

Carefully drop backside of

console as shown

Install lighter plugs and extend

wires as necessary. Slide C-VS-1000-TAH, front side

first, as shown above.

#15 #14 #13

#20

Align rear-mounting studs into

factory console holes and attach

using ¼” Serrated nuts.

Re-attach factory plug into

switch box Be sure plug is secure and

wires are carefully routed so

not to chafe

#18

#17

#16

Route all wiring to console. Wire,

and install control heads and

accessories (Sold separately)

Attach middle of VS console to factory console

using ¼” x ¾” Hex bolts and serrated nuts. For

added support #10 x ¾” screws can be installed

on front side of console

#19

For added

support install

#10 x ¾” screws

#20

Havis C-VS-1000-TAH Installation guide

Brand: Havis

Model: C-VS-1000-TAH

Type: Installation guide

Havis C-VS-1000-TAH

The C-VS-1000-TAH is easy to install and can be completed in just a few hours.

Download PDF

report

Havis C-VS-1000-TAH Installation guide

Havis C-VS-1000-TAH Installation guide

Related papers

Other documents