Havis C-DMM-102 Installation guide

Havis
Brand
Havis
Model
C-DMM-102
Category
Car kits
Type
Installation guide
INSTALL INSTRUCTIONS
C-DMM-102
1996-2011 FORD CROWN VICTORIA DASH MONITOR MOUNT
The Dash Monitor Mount bracket system requires two or three main parts that are
Sold Separately. See web site Monitor Configurator for more detailed bracket
information. http://www.havis.com/monitor_mounts.htm
• 1 - Vehicle Specific dash mount bracket. (C-DMM-102)
• 1 - Computer Specific Monitor adaptor bracket. (C-MM-200 series)
• 1 - Offset adaptor bracket. (C-MM-301)
The C-MM-301 offset adaptor goes between the C-DMM-102 and C-MM-2XX. It may not be
required in some applications.
TOOLS REQUIRED:
Ratcheting wrench
Sockets - 7/16”, 9/32”, 9/16”
Open-end wrench set – 7/16”, 9/16”
Screwdriver set
T-20 torx bit
HARDWARE:
QTY DESCRIPTION PART #
1 3/8-16 x 1 Hex bolt GSM33028
2 3/8” Flat washer GSM31007
1 3/8-16 Nylock nut GSM30018
4 ¼-20 x ¾” Phillips machine screws GSM33124
6 ¼” Serrated nuts GSM30023
6 ¼”-20 Flat washer GSM31005
2 ¼”-20 X ¾” HHC Screw GSM33001
1 Monitor adapter hardware kit Varies (monitor specific)
Always!
Read all instructions before installing any Havis, Inc. products.
Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
Use hardware provided with install kit
Related parts sold separately
:
AM-FM Radio Relocation option 1.
1 - # C-EB40-RCV-1P with 1 - # C-WH-RCV-1P Extension harness and coax cable kit.
Note: You must use a console of your choice to house this radio relocation bracket.
OR
AM-FM Radio Relocation option 2.
1 - # C-VS-800-CV with 1 - # C-EB40-RCV-1P and 1 - # C-EB40-ACV-1P
(No extension harness needed)
C-DMM-102_INST_11-09
C-DMM-102 assembly for
Ford Crown Victoria C-MM-301
Offset Adaptor
C-MM-201
Monitor mount adaptor
(VESA bracket shown)
C-DMM-102, C-MM-201 and C-MM-301 parts assembled together
C-DMM-102_INST_11-09
View with center trim panel
removed
Remove (2) OEM screws from dash
(9/32” socket)
Temporarily remove (4) HVAC
control panel screws. (9/32” socket)
Remove (2) OEM screws located
near speedometer (9/32” socket)
Carefully tug on dash trim piece
to remove.
Position C-DMM-102 bracket.
Be sure upper lip is behind dash.
Remove AM/FM radio
from dash
Disconnect and re-route radio
harness and antenna to new
mount location.
See optional C-WH-RCV kit
Remove center trim panel located
under AM/FM radio and around
HVAC controls. Simply tug
sharply on panel to remove
C-DMM-102_INST_11-09
Reposition dashboard around
C-DMM-102 bracket
Attach lower mount of assembly
to dash using 3/8” x 1” bolt,
washer and nut.
Attach support braces to C-DMM
assembly using ¼” x ¾” Phillips
machine screws and serrated nuts.
Re-attach dash trim panel
previously removed
Attach support braces to dash
using OEM screws, removed
earlier during install
Attach tilt/swivel or fixed
assembly to C-DMM assembly
using ¼” x ¾” machine screws
Attach the C-MM-301 offset
bracket to the C-DMM-102
tilt/swivel bracket.
Attach the C-MM-2XX adaptor
bracket to the monitor and connect
the assembly to the C-MM-301
offset bracket.
Run wiring and complete
installation
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Havis C-DMM-102 Installation guide

Havis
Brand
Havis
Model
C-DMM-102
Category
Car kits
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents