V-ZUG 977 Installation guide

Type
Installation guide

V-ZUG 977

The V-ZUG 977 is a top-of-the-line glass ceramic hob that offers a variety of features to make cooking easier and more enjoyable.

With its frameless design and beveled edges, the V-ZUG 977 is a stylish addition to any kitchen. The hob's smooth, easy-to-clean surface makes it a breeze to maintain.

The V-ZUG 977 features four cooking zones, each with nine power levels. This gives you the flexibility to cook a variety of dishes at the same time, from delicate sauces to searing steaks.

The hob also has a number of safety features, including a child lock and a residual heat indicator. This helps to prevent accidents and ensures that the hob is always safe to use.

V-ZUG 977

The V-ZUG 977 is a top-of-the-line glass ceramic hob that offers a variety of features to make cooking easier and more enjoyable.

With its frameless design and beveled edges, the V-ZUG 977 is a stylish addition to any kitchen. The hob's smooth, easy-to-clean surface makes it a breeze to maintain.

The V-ZUG 977 features four cooking zones, each with nine power levels. This gives you the flexibility to cook a variety of dishes at the same time, from delicate sauces to searing steaks.

The hob also has a number of safety features, including a child lock and a residual heat indicator. This helps to prevent accidents and ensures that the hob is always safe to use.

Installation instructions
Glass ceramic hob Toptronic
Frameless, with facets
J001.133-0
28.10.09 ITH
1
These installation instructions apply to the model: 001 (GK45TE.1), 977 (GK45TEAS)
Identification plate
The identification plate is next to the connection plate.
A Affix the second identification plate (enclosed) in an accessible position behind the
front of the fitted cabinet beneath the appliance.
A Information on the necessary mains voltage, type of current and fuse protection can be taken from the identification plate.
A The appliance is equipped with a mains cable that should be connected to a distribution box by the customer. For pyrometric reasons
the connection cable is not to be exchanged.
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
General notes
If fitting in flammable material, the guidelines and standards for low voltage installations and for the fire protection must be
strictly observed.
Installation accessories included
Designation Remarks Art. no.
Mounting angle right/left only with GK45TE.1C H6.3348
Mounting angle front/rear only with GK45TE.1C H6.2347
Mounting angle right/left only with GK45TEASC H6.3351
Mounting angle rear, large only with GK45TEASC H6.3350
Mounting angle front, large only with GK45TEASC H6.3349
Wood screws for mounting angle Misc.
Accessories
Designation Art. no.
Thermal screen set
for GK45TE.1
for GK45TEAS
H6.2540
H6.2617
Instant adhesive for installation in stone work surfaces
Permabond F246, incl. Activator, 50 ml tube. From Silitech AG, 3008 Bern.
B11.502
Set of fixing brackets for special installation cases H6.1548
Electrical connections
Electrical connections must be carried out by trained electricians in accordance with the guidelines and standards for low
voltage installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should
always be checked.
Connection plate
Identification plate
230 V~
AUS / NZ
PE/ green/yellow
N blue
L1 brown
400 V~ 2N
PE/ green/yellow
N blue
L1 brown
L2 black
600/550
Installation pipe
Clamp
Distribution box
Installation instructions
Glass ceramic hob Toptronic
Frameless, with facets
J001.133-0
28.10.09 ITH
2
Indications
The work surface must be flat, to ensure the required sealing against ingressing of liquids.
Installing
With wood work surfaces
1. Create the installation cut-out accurately.
2. Centre mounting rails A and B and fix in the installation cut-out with the wood screws C according to the drawing.
3. All stop positions D must be removed before installing the appliance.
4. Where necessary establish mains supply connection before inserting the appliance.
5. Lower the appliance symmetrically into the installation cut-out as far as the work surface, on to the spring catch elements.
The connection cable is not to touch the hot parts of the metal tray under the cooking zones.
With stone work surfaces
With stone work surfaces, mounting rails A and B can be bonded in place (for adhesive see «Accessories»).
1. Clean/prime the bonding surfaces on the stone and the mounting rails then allow to dry thoroughly.
2. Apply the adhesive to the stone and smooth with the spatula. Apply a thin coating of the activator to the bonding surface of the
installation rails.
3. Position the installation rails centrally and press well in. Comply with the recommended bonding time for the utilized adhesive.
4. Where necessary establish mains supply connection before inserting the appliance.
5. Lower the appliance symmetrically into the installation cut-out as far as the work surface, on to the spring catch elements.
The connection cable is not to touch the hot parts of the metal tray under the cooking zones.
Installation
The distance from the appliance cut-out to flammable walls (left, right and rear) must be at least 50 mm. Parts such as partition
walls, reinforcing strips which protrude into the installation space under the cooking zone must be of non-flammable materials.
The distance between the underside of the appliance tray and any kitchen unit parts of flammable material must be at least
20 mm. When installed directly under a drawer and if the tray can be reached from below without tools, a protective guard must
be used. The thermal screen set (see «Accessories») is recommended.
The layout of the cooking zones on the integrated hob may differ from the illustrated hob!
GK45TE.1 GK45TEAS
A
B
A
B
min. 30
600
750 ±1
490 ±1
min. 50
560 ±1
584
514
774
514
490 ±1
min. 50
min. 30
600
600/550
600/550
CD
23
Aim for a
max. of R10
max. 39.2
from support
Set of fixing brackets for
special installation cases
Aim for a
max. of R10
Centering marks,
front/rear
Centering mark,
middle of cut-out
Centering mark, rear,
middle of cut-out
Centering mark, front
max. 39.2
from support
min.61.5
Cable length 1.5 m Cable length 1.5 m
  • Page 1 1
  • Page 2 2

V-ZUG 977 Installation guide

Type
Installation guide

V-ZUG 977

The V-ZUG 977 is a top-of-the-line glass ceramic hob that offers a variety of features to make cooking easier and more enjoyable.

With its frameless design and beveled edges, the V-ZUG 977 is a stylish addition to any kitchen. The hob's smooth, easy-to-clean surface makes it a breeze to maintain.

The V-ZUG 977 features four cooking zones, each with nine power levels. This gives you the flexibility to cook a variety of dishes at the same time, from delicate sauces to searing steaks.

The hob also has a number of safety features, including a child lock and a residual heat indicator. This helps to prevent accidents and ensures that the hob is always safe to use.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI