PAC WRI-P User manual

PAC
Brand
PAC
Model
WRI-P
Type
User manual
1
11-17-09
WRI-P
Wired Remote Input Control Interface
Before You Start
A. Prepare for the installation.
• If possible, install the WRI-P while you are installing the new head unit.
• Plan a general installation location for both the WRI-P infrared eye and the control body.
• If you are installing the WRI-P in conjunction with a SWI-PS, please refer to the SWI-PS instructions for all wiring
and programming information.
Pacific Accessory Corporation
IP-BUS input
Antenna jack
Power
To Infrared Eye
Fuse
Jack for the SWI-PS
IP-BUS cable
WRI-P
Installation Instructions
Compatible with Pioneer in-dash
navigation units that lack an IR receiver
but have a wired remote input.
Wiring Connections
Step 1.
Connect the BLACK
wire to ground (-).
Verication: Wire
or location registers
a constant (-) when
probed.
Step 2.
Connect the RED wire
to switched +12V.
Verication: Wire reg-
isters +12V when the
ignition key is turned
to the ACC or ON posi-
tions.
WRI-P
Black
Red
WRI-P
Black
Red 12V+ (Switched)
2
Step 3.
Connect the 3.5mm stereo plug on 5 pin Molex to the wired remote input on
the back of the radio..
Black
Red 12V+ (Switched)
WRI-P
Back of Radio
Wired Remote In
Step 4
Mount the infrared eye in a suitable location
Compatibility Notes
1. The voice recognition command via wireless remote is not supported on the following models: AVIC-F700BT, AVIC-F900BT,
AVIC-U310BT, AVIC-X710BT, and AVIC-X910BT.
2. PAC recommends the use of the Pioneer CD-R510 or CXC9115 remote for maximum compatibility with the WRI-P. Other
Pioneer remotes may work, but some functions / buttons may not be supported.
Step 5
If applicable, install the SWI-PS and connect
the 3.5mm plug to the SWI-PS input on the
side of the WRI-P
WRI-P SWI-PS
WRI-P Functions
CD-R510 Function
VOLUME + Volume up
VOLUME - Volume down
BAND Band
SRC Source
ATT Mute/Attenuate
PGM Phone Status
OFF/H Answer Call
ON/H End Call
Joystick Function
UP Preset +
DOWN Preset -
RIGHT Seek >>
LEFT Seek <<
Center Voice Activation
Note: CLEAR
button is for self
testing of WRI-P.
WRI-P
Black
Red 12V+ (Switched)
To Suitable
Location
Troubleshooting
The WRI-P has a self test mode which can determine if it is sending and receiving the proper signals. Follow the steps below to
engage the self test mode:
1. Connect the module to a 12v source (do not apply power yet).
2. Connect the 3.5mm output plug on 5 pin Molex to the 3.5mm input on the side of the module.
3. Connect the IR receiver to the WRI-P.
4. Power up the WRI-P
5. Using the CD-R510 remote, point the remote at the IR receiver and press the CLEAR button on the remote to start the test.
The LED will blink 9 times while testing the analog outputs and inputs then pause for a second. It will blink 3 times to conrm it
passed the test.
See
troubleshooting
section below
Pacic Accessory Corporation - Santa Ana, CA 92705
866-931-8021• www.pac-audio.com
  • Page 1 1
  • Page 2 2

PAC WRI-P User manual

PAC
Brand
PAC
Model
WRI-P
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents