Paxton OEM Magstripe 1000 compact system User guide

Brand: Paxton

Model: OEM Magstripe 1000 compact system

Type: User guide

Paxton OEM Magstripe 1000 compact system offers robust security solutions for various settings. Ideal for security-sensitive doors, wet environments, and mounting on metal surfaces, it seamlessly integrates with Track 2 ISO magstripe cards. With a user-friendly interface, the system enables easy fitting, wiring, and operation.

Ins-30034 OEM Magstripe 1000 compact system

21/12/2011

Suitability

Security-sensitive doors

Wet environments

Fitting

Compatible with any Track 2 ISO magstripe card

Mounted on metal surface

Exit button

(push to make)

Electric release

12V DC power

supply

12V DC release current rating must be less than 1A.

+12V

Exit

Wiring

Master Card - must be swiped when the system is rst switched on

1. Take the master card from the new pack of paper shadow cards.

2. Swipe the master card through the reader.

3. The reader beeps and the LED's light up as the master card is acknowledged.

4. The pack is now ready for adding cards.

Issuing tokens

1. Write the name of the user on a shadow card.

2. Swipe the shadow card through the reader.

3. Swipe the chosen user card through the reader - it is now enrolled.

4. Store the shadow card in a safe place.

Bar a user

1. When a card is lost or stolen it is important to bar the card from your system to avoid unauthorized access.

2. To bar a card or token take it's corresponding shadow card from the card pack.

3. Present the shadow card to the reader. This will remove the lost card or token from your system.

4. A barred card can re-validated by presenting the enrolment card followed by the user card to the reader.

BEEP!

Master Card

1. At installation, present this

card to the reader to validate

the tokens in this pack.

2. To re-validate a user token,

present this enrolment card

to the reader followed by the

user token.

Master Card

1. To enrol a user card, write the iser’s name on

a paper card, swipe it through the reader, then

swipe the user card through the reader

2. To set the door open time, swipe this card, the

reader will beep, wait for the required period,

swipe the card again, the bleeping will stop.

1 2 3 4

Master Card

1. At installation, present this

card to the reader to validate

the tokens in this pack.

2. To re-validate a user token,

present this enrolment card

to the reader followed by the

user token.

Master Card

1. At installation, present this

card to the reader to validate

the tokens in this pack.

2. To re-validate a user token,

present this enrolment card

to the reader followed by the

user token.

Swipe this card to bar:

Write name:

John Smith

Swipe this card to bar:

Write name:

John Smith

1 2 3 4

John Smith

User Card

CARDLOCK

1 2 3 4

Swipe this card to bar:

Write name:

John Smith

5. Alternatively a different user card can be swiped which will then pair that user card with the paper shadow card.

Fail Open release card - (Unit default = Fail Closed)

THIS CARD CAN ONLY BE USED WITH A FAIL OPEN LOCK.

1. Take the fail open release function card from the starter pack.

2. Present/swipe the card through the reader. The reader will beep for about a second.

3. The reader is now set to fail open mode. This allows safe operation of the door in case of re: The lock will

release when the power is cut.

4. To revert to fail closed mode, swipe the card again and the reader will beep once.

BEEP!

1 2 3 4

This card is used with systems where a fail open

electric release is used for the safe operation in the

event of a fire. Present the card to the reader to

drive a fail open release or a maglock. Present the

card again to revert to the fail closed operation

Paxton Access

FUNCTION CARD

fail open release

Door open time (Unit default = 7 seconds)

1. Take the master card from the starter pack.

2. Swipe the card through the reader. The reader will start beeping.

3. Wait for the required period you wish the door to remain open.

4. Swipe the card again at the end of the period to set the open time. The beeping will stop.

3 4

BEEP!

Master Card

1. To enrol a user card, write the user’s name on a paper

card, swipe it through the reader, then swipe the user

card through the reader.

2. To set the door open time: swipe this card, the reader

will beep, wait for the required period, swipe the card

again, the bleeping will stop

Master Card

1. To enrol a user card, write the user’s name on a paper

card, swipe it through the reader, then swipe the user

card through the reader.

2. To set the door open time: swipe this card, the reader

will beep, wait for the required period, swipe the card

again, the bleeping will stop

Master card

1. To enrol a user card, write the user’s name on a paper

card, swipe it through the reader, then swipe the user

card through the reader.

2. To set the door open time: swipe this card, the reader

will beep, wait for the required period, swipe the card

again, the bleeping will stop

Adding a new pack of shadow cards (up to 4)

1. Take the master card from the original card pack.

2. Swipe the original master card.

3. Swipe the master card from the new pack you wish to enrol.

4. The new pack is now enrolled. Return both master cards to their respective packs.

- Up to 4 shadow card packs can be enrolled onto the system.

1 2 3 4

CARDLOCK

enrolment card

1. A

t installation, present this

card to the reader to

validate

the to

kens in this pack.

2. To re-validate a user to

ken,

present this enrolment card

to the reader followed by the

user to

ken.

Master Card

1. To enrol a user card, write the user’s name on a paper

card, swipe it through the reader, then swipe the user

card through the reader.

2. To set the door open time: swipe this card, the reader

will beep, wait for the required period, swipe the card

again, the bleeping will stop

BEEP!

Master Card

1. To enrol a user card, write the user’s name on a paper

card, swipe it through the reader, then swipe the user

card through the reader.

2. To set the door open time: swipe this card, the reader

will beep, wait for the required period, swipe the card

again, the bleeping will stop

To delete a card pack

Factory reset

1. Power down the unit.

2. Press and hold down the exit button.

3. Power up the unit. After 3 seconds the Red LED will come on and the unit beeps.

4. The unit will then reset and all the LED's will come on.

5. Release the exit button.

User cards are NOT supplied with this unit. Please supply your own user cards.

Compatible with any Track 2 ISO magstripe card

Voltage

Maximum load output current

Reader head life

-20 °C +55 °C

IPX7

1,000,000

11V DC 14V DC

90 mA 110 mA

1 A

300 Oe 4000 Oe Lo-Co & Hi-Co

1000

4 x 250

34 mm 89 mm

34 mm

Specications

Electrical

Environment

Dimensions

Min

Max

Width

Height

Depth

Current

Operating temperature

Cable length

Reader

IP Rating

Outdoor use

Swipes

Number of Cards

Number of Card Packs

Magnetic stripe coercivity

1. Card packs may be deleted from the system if required. Once a card pack has been deleted another one may

be enrolled in its place.

2. To delete a card pack, take the master card and swipe it backwards through the reader.

3. Swipe the master card backwards again and the reader LED's will go out. After 5 seconds the reader will beep

and the LED's will come back on.

4. The card pack will now have been removed from the system.

3 metres

Min

Max

Paxton OEM Magstripe 1000 compact system User guide

Paxton OEM Magstripe 1000 compact system User guide

Paxton OEM Magstripe 1000 compact system User guide

Related papers

Other documents