Grizzly T10157 Owner's manual

Brand: Grizzly

Model: T10157

Type: Owner's manual

MODEL T10157

OAK WORKBENCH

INSTRUCTIONS

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MANUFACTURED SINCE 1/10) #TS11313 PRINTED IN CHINA

Figure 1. Model T10157 Oak Workbench.

Features

• Solid 1

⁄2" thick oak top with double rows of

bench dog holes for each vise.

• Two storage drawers (with ball bearing slides)

that are 10

⁄4" wide x 12

⁄4" long x 2

⁄4" deep.

• Sturdy adjustable steel legs with leveling foot

pads.

• Two oak-faced vises with removable top plate

and 4" leadscrew travel, 13" wide x 2" thick.

• Four bench dogs and a bench stop bar.

• All wood surfaces finished with durable lac-

quer.

• Overall dimensions: 62" wide x 30" in depth x

32"–39" tall.

• Weight: 155 lbs.

Inventory

Use the parts breakdown and listing on Page 4 to

perform an inventory of the shipment.

If any nonproprietary parts are missing (e.g. a

bolt or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

Assembly

Tools Needed Qty

Phillips Screwdriver #2 ...................................... 1

Wrench or Socket

⁄2" ........................................ 1

To assemble your workbench:

1. Fit each drawer bottom into the front and

rear panels, then install the side panels with

wood glue and (16) wood dowels, as shown

in Figure 2. Secure the assemblies with (16)

#8 x 1

⁄4" wood screws.

NOTICE

If you cannot find an item on the inventory

parts list, check the mounting location on

the workbench or examine the packaging

materials carefully. Some items are pre-

installed for shipping purposes.

Figure 2. Attaching drawer side panels.

x 8

-2-

Model T10157 (Mfg. Since 1/10)

2. With assistance from another person, place

the table top upside down on a flat, protected

surface.

3. Slide the lower legs into the upper legs, then

secure them together with (8)

⁄16"-18 x

⁄4"

hex bolts and

⁄16" flat washers, as shown in

Figure 3.

Note: Make sure that the completed leg

assemblies are all the same length, which will

dictate the height of the finished workbench

(from 32"–39").

Note: In the next step, take care to properly

orient the leadscrew holes in the leg assem-

blies with the holes in the table top to accept

the vise leadscrews in a later step (see

Figure 5).

5. Secure the leg assemblies to the workbench

top with (16)

⁄16" x 1" lag screws, as illus-

trated in Figure 5.

Note: In the next step, orient the leadscrew

holes in the legs so that one hole faces to the

side, and the other faces to the front. This is

necessary to properly install the vise assem-

blies in a later step.

4. Attach the leg supports to the leg assemblies

with (8)

⁄16"-18 x

⁄4" hex bolts and

⁄16" flat

washers, as shown in Figure 4.

Figure 3. Upper and lower leg.

x 8

Upper

Leg

Lower

Leg

Figure 5. Leg assemblies installed.

Leadscrew Hole

x 16

Figure 4. Leg assemblies.

x 8

Leg

Support

Leadscrew Hole

Model T10157 (Mfg. Since 1/10)

-3-

12. Slide each vise assembly into the vise faces,

as illustrated in Figure 8, then secure them

with (8) #8 x 1" wood screws.

13. Install the drawers, then insert the bench stop

bar and bench dogs into the workbench top to

finish the assembly.

Figure 7. Bottom shelf installed.

x 4

Bottom Shelf

11. Remove the caps from the wooden handles,

insert the handles through the ends of the

vise assemblies, then glue the caps back on

the handles, as illustrated in Figure 8.

Note: In the next step, make sure that the

drawer slides on the support assemblies are

facing the correct way to accept the draw-

ers.

6. Use wood glue and (6) wood dowels to attach

the drawer support assemblies to the table

top, as illustrated in Figure 6.

Figure 6. Installing drawer support assemblies.

x 6

Drawer Support

Assembly

Leadscrew

Plates

7. Further secure the drawer support assem-

blies to the table top with the (9) #10 x 1

⁄2"

wood screws (see Figure 6).

8. Secure the leadscrew plates (see Figure 6)

to the underside of the table top with (12) #8

x 1" wood screws.

9. With assistance, flip the workbench right side

up, move it to its final location, then adjust the

foot pads to make the table level and stable.

10. Attach the bottom shelf to the legs with (4)

⁄16"-18 x

⁄4" hex bolts and

⁄16" flat washers,

as shown in Figure 7.

Note: You can install the shelf with the lip

facing up or down.

Figure 8. Vise assembly installed.

x 4

Wooden Handle

& Cap

Vise Assembly

-4-

Model T10157 (Mfg. Since 1/10)

Parts Breakdown and List

20-1

REF PART # DESCRIPTION QTY REF PART # DESCRIPTION QTY

1 PT10157001 VISE LEADSCREW ASSEMBLY 2 21 PT10157021 LOWER LEG 4

4 PT10157004 WOOD DOWEL M8 X 30 22 22 PT10157022 FOOT PAD M14- 2.0 X 50 4

5 PWS005 WOOD SCREW #8 X 1-1/4 22 23 PT10157023 BOTTOM SHELF 1

7 PT10157007 BALL BEARING DRAWER SLIDE 4 24 PT10157024 LAG SCREW 5/16" X 1" 16

8 PT10157008 WOOD SCREW M4 X 13 12 25 PB07 HEX BOLT 5/16-18 X 3/4 20

9 PT10157009 WORKBENCH TOP 1 27 PWS006 WOOD SCREW #8 X 1 20

10 PT10157010 VISE FACE 2 28 PT10157028 LEADSCREW PLATE 2

11 PT10157011 BENCH STOP BAR 1 29 PT10157029 LEG SUPPORT 2

12 PT10157012 VISE HANDLE ASSEMBLY 2 30 PW07 FLAT WASHER 5/16" 20

14 PT10157014 BENCH DOG 4 31 PN40 ACORN NUT 5/16-18 4

15 PT10157015 DRAWER PANEL FRONT 2 32 PT10157032 DRAWER SUPPORT W/RAIL 3

16 PT10157016 DRAWER PANEL LEFT 2

PT10157033 UPPER LEG W/O LEADSCREW HOLE 2

17 PT10157017 DRAWER PANEL RIGHT 2 34 PT10157034 VISE ROD 4

18 PT10157018 DRAWER PANEL BACK 2

PT10157035 VISE ROD WASHER 4

19 PT10157019 DRAWER PANEL BOTTOM 2

PT10157036 VISE BOLT 4

20 PT10157020 UPPER LEG W/SIDE LEADSCREW HOLE 1

PWS001 WOOD SCREW #10 X 1-1/2 9

20-1 PT10157020-1 UPPER LEG W/FRONT LEADSCREW HOLE 1

PW10M FLAT WASHER 14MM 4

parts

Grizzly T10157 Owner's manual

Grizzly T10157 Owner's manual

Grizzly T10157 Owner's manual

Related papers

Other documents