USER MANUAL
SOUND STAND
PORTABLE
SPEAKER
kitsound.co.uk
Li-PO
Do not dispose of Lithium Polymer
batteries with general waste.
Please return it to battery recycling
collection point
JB. 2623 / Made in China. © KitSound
™
2013 Christchurch, Dorset. BH23 4FL
We are craftspeople. We are musicians. We are KitSound
™
And we all commit ourselves to achieving one shared goal: Bringing
people closer to their music. By truly understanding music we stay true
to its craft. Pure, rich, incredible sound. We’ll settle for nothing less.
At KS we believe your music deserves to be showcased on great
quality products that don’t cost the earth. We might not all share
the same taste in music (the ferocious disputes on music forums
prove that), but whether it’s Irish folk, death metal or any number
of obscure genres which seem to be multiplying by the minute, the
artists responsible for connecting with you through their craft have
bared their souls to do so. And we think that’s worth celebrating.
6 7
Like the musicians we’re honouring, we’re obsessed with our craft;
fine-tuning and tweaking our products to make sure we constantly
deliver full-bodied, symphonic sound. So from a single note played
on a piano, to the full impact of a bass guitar, you can rest assured
that you’ll always be doing justice to your music.
8 9
Charging the battery
The Sound Stand has a built-in rechargeable lithium battery.
Make sure the Sound Stand is switched off. Connect one end of the USB power cable to the charging
port of the Sound Stand and connect the other end to your PC or USB mains adaptor. The battery will
start charging.
• It takes approx. 2 hours to fully charge the battery
• Whilst charging, the LED will show red
• When fully charged, the LED will turn blue
• A fully charged unit has up to 4 hours of playback time
LED indicator
There is an LED light on the front of the Sound Stand. Please see below explanations for what each LED
indication means.
– LED off: Power OFF
– Solid blue: Power ON/fully charged
Using the speaker
• If you’re using a tablet, place it in the dock and then tighten the screws on the back of the Sound Stand
until the tablet is secure
• Fold out the legs on the back of the speaker
• Using the provided aux cable, connect one end to the Sound Stand and the other end to the headphone
socket on your device
• Switch the speaker to ‘ON’ or ‘SRS’ mode. SRS mode will provide a wider sound than normal. As everyone’s
hearing is different, please try both modes to find which best suits your ears
• Press ‘Play’ on your device and turn up the volume to a comfortable level
Other Information
Your device will have an internal amplifier and if it is playing digital files like MP3s it will also have an
integrated DAC (Digital Audio Converter). If you turn the volume up to 100%, your device will be sending
a distorted signal. To avoid this, and to get the best quality from the speaker, we recommend that you do
not run your device any higher than 95% volume. Some devices output higher than others, so you may
need to reduce the volume if you experience distortion.
10 11
Care and maintenance
Wipe the unit with a soft dry dust cloth. Do not use any wax, polish sprays or abrasive cleaners on it.
Caution:
Never allow any water or other liquids to get inside the unit while cleaning.
Specifications
• Play time: up to 4 hours
• Drivers: 2 x 30 mm NdFeb
• S/N: 78 dB
• Frequency response: 80 Hz – 17.5 kHz
• Jack socket: 3.5 mm
• Surround engine: SRS
®
Box contents
• KS Sound Stand speaker
• 3.5 mm aux cable
• Mini USB charge cable
• User manual
Troubleshooting
We hope you’ve now got all the information you need to get started, but if you’re having problems with
anything, please feel free to contact us at: support@kitsound.co.uk
/