Magnadyne DVU-3G2 Installation guide

Brand: Magnadyne

Model: DVU-3G2

Type: Installation guide

Magnadyne DVU-3G2 is a dual VPA socket and USB port adapter that gives you the ability to charge multiple devices simultaneously while you're on the go. With its screw or Velcro mount, you can easily install it in your vehicle without obstructing your view. It's designed for continuous operation and features a 15A switched power source to prevent draining your vehicle's battery when the ignition is off. The USB port allows you to connect and charge USB-powered devices, while the two VPA sockets are compatible with VPA chargers.

Dual VPA Socket and USB Port Adapter

Model: DVU-3G2

Installation Instructions

DVU-3G2-INS Rev. B 3-5-13

Mounting the Unit

Screw Mount:

The DVU-3G2 comes with screws to permanently mount the

unit to the dashboard or some other area in the vehicle.

1. Make sure that the mounting location does not interfere

with the operation of the vehicle. Also make sure the

screws will not damage anything behind the dash.

2. Use the provided screws to mount unit.

Velcro Mount:

The DVU-3G2 comes with a Velcro pad for mounting the unit to

the dashboard or some other accessible area in the vehicle.

1. Make sure the surface area where the Velcro will adhere to is

clean. The area must be free from any interior protectorants.

2. Remove the backing on one side of the Velcro pad and apply

the to the DVU-3G2.

3. Remove the backing on the other side of the Velcro pad and

press the unit firmly into the designated mounting location.

Hard Wiring:

The DVU-3G2’s can be hard wired for permanent installation in

a vehicle

1. Cut off the VPA connector making sure to leave the

enough cable to reach the connection point.

2. Connect the wire with the white stripe to a fused 15A

switched power source.

Note: If the wire with the white stripe is not connected to a

switched power source when the ignition is turned off the

DVU-3G2 will continue to draw its power from the vehicle’s

battery and over an extended time may drain the battery.

3. Connect the black wire to chassis ground.

Optional Hard Wiring

Warnings

•

FCC REGULATIONS STATE THAT ANY UNAUTHORIZED CHANGES OR MODIFICATIONS

TO THIS EQUIPMENT MAY VOID THE USER’S AUTHORITY TO OPERATE IT.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT INSTALL THE

UNIT IN A PLACE EXPOSED TO DIRECT SUNLIGHT OR EXCESSIVE HEAT OR

HUMIDITY. AVOID PLACES WITH TOO MUCH DUST OR THE POSSIBILITY OF

WATER SPLASHING OR GETTING WET.

• THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING

INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

• IN CERTAIN VEHICLES THE

ADAPTER WILL DRAW POWER EVEN WHEN VEHICLE

IS TURNED OFF AND DEPENDING ON USAGE MAY DRAIN THE VEHICLE’S BATTERY

• Never install the product in a location where it interferes with your field of vision.

•

Use the proper power supply. This product is designed for operation with a neg-

ative grounded 12V DC battery system. If the product is used with the improper

system it may cause a fire or an accident.

• This product must be installed and used in accordance with this manual. Any alter-

ations to this product that enables it to be used in any way other than intended or

designed could distract the driver and result in an accident causing injury or death.

Magnadyne Corporation disclaims any and all liability that may result from failure

to install and operate in any other manner in which this unit was intended.

•

Do not disassemble, modify the unit or attempt to repair the product yourself. If

the product needs to be repaired, consult your dealer.

Caution

Conect the Wire with the White Stripe

to a Fused 15A Switched Power Source

Conect the Black Wire

to Chassis Ground

Dual VPA Socket and USB Port Adapter

Model: DVU-3G2

Note: Power consumption for all connected devices shall not exceed 120 watts.

Operation Instructions

Changing the Fuse:

Should the DVU-3G2 fail to operate, replace the fuse

1. Unplug the DVU-3G2’s VPA plug from the vehicle’s power socket.

2. Use a fuse puller to remove the fuse.

3. If the fuse is burnt, place a new fuse with exactly the same

amperage rating (15 Amp).

Plug the VPA plug back into the vehicle’s power socket.

5. If the DVU-3G2 works correctly after fuse replacement con-

tinue to use the device.

Note: If the DVU-3G2 does not function properly and the new

fuse blows immediately, there is a problem and discontinue

use.

Trouble Shooting

USB Operation Instructions

Inserting a USB Cable:

Gently insert the USB drive into the slot.

Note: If a USB connector does not insert, DO NOT FORCE it into

the slot, flip the connector over and try again

Inserting a VPA Charger:

Remove the cover from a VPA socket. The interior of the

socket will be illuminated green indicating the unit has power.

2. Insert the VPA into the socket. Make sure to fully insert the

charger.

3. To remove the charger hold the DVU-3G2 and pull the VPA

charger out of the socket. Do not pull the VPA’s cable to

remove the charger.

Removing a USB Cable:

Pull the USB connector straight out of the socket. Do not pull

the USB’s cable to remove the USB connector from its socket.

Damage may occur.

VPA Operation Instructions

DO NOT USE CIGARETTE

LIGHTERS WITH THIS UNIT.

15A

Magnadyne DVU-3G2 Installation guide

Magnadyne DVU-3G2 Installation guide

Magnadyne DVU-3G2 Installation guide

Related papers

Other documents