BMW 84 64 0 302 178 Installation Instructions Manual

BMW
Brand
BMW
Model
84 64 0 302 178
Type
Installation Instructions Manual

This manual is also suitable for

Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
Universal BMW Hands-Free Kit Upgrade
BMW X5 (E
53) from 09/01 to 03/02
These installation instructions are only valid for cars with SA 640 (telephone preparation).
Important information
This upgrade kit is for use within the BMW dealership organisation only.
Subject to technical modifications.
Target group
The target group for these installation instructions is specialist personnel trained on BMW cars with the
appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and
work instructions in a rational order using the prescribed tools (special tools) and observing current health and
safety regulations.
Installation information
Ensure that the cables/lines are not kinked or damaged as you install them in the car.
The installed cables are to be secured with cable ties.
If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used.
Ordering instructions
The snap-in adapter is not part of the upgrade kit and must be ordered separately.
Installation time
Approx. 4 hours, but this may vary depending on the condition of the car and the equipment in it.
Pictograms
denotes instructions that draw your attention to special features
.
denotes the end of the instruction or caution text.
Retrofit kit No.
84 64 0 153 493
84 64 0 302 178
Special tools required
Removal tool (00 9 341)
Parts and Accessories
Installation Instructions
EN/2
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
Contents
Section Page
1. Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5. To install and connect the universal charger/hands-free electronic control unit . . . . . . . . . . . . . . . 7
6. To install and connect the eject box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. To install the hands-free microphone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8. Concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
9. Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
EN/3
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
1. Preparations
0
TIS instruction No.
Conduct a brief test
---
Disconnect the negative pole of the battery 12 00 ...
The following components must be removed first of all:
Backrest side section, left 52 26 008
Left boot – wheel arch trim 51 47 151
Rear seat bench 51 24 005
Front left door sill trim 51 47 000
Rear left door sill strip 51 47 030
Front left seat 52 .. ...
B pillar trim at the bottom left 51 43 150
Armrest
---
Ceiling light 63 31 000
EN/4
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
2. Parts list
0
Legend
AEject box
BRear base holder
CFront base holder
DULF holder
E Holding bar
F WDCT aerial
G Hands-free microphone
H ULF (universal charger/hands-free electronic control unit)
I Hexagonal nut M6 (4x)
J Hexagonal screw M5 x 14 (4x)
K Speed nut M5 (4x)
LCap nut M5
M Hexagonal screw M5 x 10-ZI (4x)
OEject box adapter
PULF adapter
QAerial cable
A D ECB
HGF JI MK L
PO
Q
053 0443 Z
EN/5
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
3. Connection diagram
0
Legend
Item Description Signal
Cable colour /
Cross-section
Connection location in the car Abbreviation / Slot
O Eject box adapter --- --- --- ---
O1 SW 18-pin plug --- --- To standard wiring harness X4545
O2 FAKRA socket contact --- --- To standard wiring harness X13322
O3 SW 18-pin plug --- --- To eject box X4545
O4 FAKRA plug contact --- --- To eject box X13322
P ULF adapter --- --- ---
P1 WS 18-pin plug --- --- To standard wiring harness X18618
P2 BL 26-pin plug --- --- To standard wiring harness X18626
P3 SW 54-pin plug --- --- To ULF X4038
Q Aerial cable --- --- --- ---
Q1 FAKRA socket contact SW --- --- To WDCT aerial ---
Q2 FAKRA socket contact WS --- --- To ULF ---
Q1 Q2
Q
P2
P1
O1
O2
P3
O3
O4
P
O
053 0444 Z
EN/6
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
4. Installation and cabling diagram
0
Legend
AEject box
F WDCT aerial
G Hands-free microphone
H ULF (universal charger/hands-free electronic control unit)
OEject box adapter
PULF adapter
QAerial cable
AG
O
P
H
F
Q
053 0580 Z
EN/7
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
5. To install and connect the universal charger/hands-free electronic control unit
0
0
0
0
0
Use the hexagonal nuts I and hexagonal screw M to
screw on the universal charger/hands-free electronic
control unit holder D in the boot on the left.
Push the speed nuts K onto the universal charger/hands-
free electronic control unit holder D.
0
Push the speed nuts K onto the front module holder C
and use the hexagonal screws J to screw it onto the rear
module holder B.
Use the hexagonal screws J and M and hexagonal nuts I
to screw the rear and front module holders B and C into
the boot on the left.
0
Connect branches P1 and P2 to plugs X18618 and
X18626.
0
Connect branches P3 and Q2 to the universal charger/
hands-free electronic control unit H.
Make sure that the standard aerial cable (1) is
plugged onto the standard wiring harness.
I
K
M
D
053 0351 Z
J
J
K
I
C
B
M
053 0352 Z
X18626
X18618
P2
P1
053 0431 Z
P3
1
H
Q2
053 0445 Z
EN/8
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
5. To install and connect the universal charger/hands-free electronic control unit
0
0
0
0
Place the universal charger/hands-free electronic control
unit H and holding bar E against the universal charger/
hands-free electronic control unit holder D and screw on
using the cap nuts L.
0
Use the cap nuts L to screw the WDCT aerial F onto the
front module holder C.
0
Connect the branch Q1 to the WDCT aerial F.
E
H
D
L
053 0354 Z
C
F
L
053 0355 Z
Q1
F
053 0442 Z
EN/9
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
6. To install and connect the eject box
0
0
0
0
0
Disconnect the plug connection (1) and remove the
existing extension cable (2) (no longer required).
0
Undo the Allen bolts (1) from the armrest (2) and remove
the cover (3).
0
0
Take the springs (1) out of the armrest (2).
Remove bolts (3) with a punch and pull the guide arm (4)
upwards.
0
0
Unclip the covers (1) from the guide arms (2).
2
1
053 0222 Z
3
2
1
053 0035 Z
2
1
3
4
053 0036 Z
1
2
053 0037 Z
EN/10
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
6. To install and connect the eject box
0
0
0
0
0
Pull the slide plate (1) on the armrest (2) backwards as far
as it will go.
Release the retaining pins on the oddments box (3) with
screwdrivers (4) and unclip the oddments box (3).
0
Clip the eject box A into the armrest (1).
0
0
Connect the branch O3 to the black 18-pin plug (1) of the
eject box.
Connect branch O4 to the aerial cable of the eject box (2).
Insert the adapter cable
O
into the guide arms (1) as shown.
0
0
Clip the covers (1) into the guide arms (2).
1
2
3
4
053 0048 Z
A
1
053 0434 Z
1
2
O3
O4
1
O
053 0435 Z
2
1
053 0210 Z
EN/11
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
6. To install and connect the eject box
0
0
Install the armrest back on to the centre console.
Connect branch O1 to plug X4545.
Connect branch O2 to the vehicle aerial cable (1).
O1
O21
X4545
053 0436 Z
EN/12
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
7. To install the hands-free microphone
0
0
0
0
Thread the tied back plug X4221 through the
microphone opening (1) in the headlining console (2).
0
Clip the hands-free microphone G into the microphone
trim (1) removed previously.
Connect plug X4221 to the hands-free microphone E.
0
The arrow on the hands-free microphone G must
point to the front of the car.
Clip the microphone trim (1) into the headlining console (2).
X4221
1
2
053 0044 Z
1
G
X4221
053 0350 Z
1
2
053 0046 Z
EN/13
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
8. Concluding work
0
This upgrade system requires coding and must be coded using DISplus, MoDiC III or GT1 via the
"Retrofit" path.
- Connect battery
- Conduct a brief test with DISPlus/MoDiC III/GT1
- Synchronize the mobile phone and the universal charger/hands-free electronic control unit
- Activate the Bluetooth function of the mobile phone (see the mobile phone owner's manual)
- Press and hold the push-to-talk button for about 1 second whilst switching on terminal R
- Release the push-to-talk button. The radio display shows "BT PAIRING" and the MID or on-board
monitor displays "BLUETOOTH PAIRING".
The checklamps on the MID or on-board monitor flash during the connection phase.
- Activate the "Locate Bluetooth Devices" menu on the mobile phone (see the mobile phone owner's
manual). This process may take a few minutes.
- Work through additional menus in accordance with the instructions displayed on the mobile phone
- When prompted to do so, enter the 4 digit "BLUETOOTH PASSKEY" (see the sticker on the owner's
manual) using the mobile phone keypad
- The radio, MID or on-board monitor displays "SUCCEEDED" to confirm that synchronisation has been
carried out correctly
- Switch off the ignition – the connection is terminated
- Conduct a function test
- Assemble the car again following the instructions to dismantle it in reverse order
EN/14
Retrofit kit No. 84 64 0 153 493
Installation Instructions No. 01 29 0 153 674 Issue date: 09.2002
9. Circuit diagram
0
Legend
X3368 Terminal 30 connector
X4038 SW 54-pin plug
X4545 SW 18-pin plug
X13322 FAKRA plug SW
X18618 WS 18-pin plug
X18626 BL 26-pin plug
2
KL. 31
36
0,5 RT
KL. 31
X13322
X13322X4545
1
0,48 WS
0,5 SCHIRM
ANT
SCHIRM
ANT
SCHIRM
1
9
CRADLE KEY+
1
0,35 SW WS
0,35 WS BR
CRADLE KEY+
2
KL. 31
1
KL. 30
5
0,35 RT
KL. 30
X4545
13
CRADLE_ON
13
0,35 VI WS
CRADLE_ON
2
KL. 31
X4038
6
KL. 31
39
0,35 VI WS
0,35 SW
KL. 31
5
CRADLE_ON
11
TELE
33
0,35 WS
TELE
X18626
X18618
24
KL.30
10
CRADLE KEY+
32
0,35 WS GR GE
CRADLE KEY+
1
30<39
17
0,5 RT
30<39
7
I-BUS
15
0,5 BR
I-BUS
8
KL. R
35
0,5 BR
KL. R
15
TEL_MUTE
51
0,35 BL WS
TEL_MUTE
11
TEL_ON
34
0,5 BR
TEL_ON
6
NF_OUT-
38
0,35 SW BR
LS/DSP-
6
NF_OUT+
37
0,35 SW WS
LS/DSP+
15
MIK-
19
0,35 BR WS
FSP_MIC-
16
MIK+
1
0,35 WS
FSP_MIC+
7
SCHIRM
21
0,35 SCHIRM
SCHIRM
11
CRADLE_ON
X3368
VB 30
0,5 RT
0,35 RT
053 0437 Z
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

BMW 84 64 0 302 178 Installation Instructions Manual

BMW
Brand
BMW
Model
84 64 0 302 178
Type
Installation Instructions Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents