Toro Channel Reinforcement Kit, Z400 Z Master Mower Installation guide

Toro
Brand
Toro
Model
Channel Reinforcement Kit, Z400 Z Master Mower
Category
Car kits
Type
Installation guide

Toro Channel Reinforcement Kit, Z400 Z Master Mower is a device designed to reinforce the channel of your Z400 Z Master Mower. It comes with all the necessary parts and detailed instructions to help you install it easily. The kit includes a small channel plate, bolts, flanged lock nuts, and spacers. The long spacers are used for the rear bolts, and the short spacers are used for the front bolts.

Once installed, the Toro Channel Reinforcement Kit will help to strengthen the channel of your mower, making it more durable and resistant to damage.

Toro Channel Reinforcement Kit, Z400 Z Master Mower is a device designed to reinforce the channel of your Z400 Z Master Mower. It comes with all the necessary parts and detailed instructions to help you install it easily. The kit includes a small channel plate, bolts, flanged lock nuts, and spacers. The long spacers are used for the rear bolts, and the short spacers are used for the front bolts.

Once installed, the Toro Channel Reinforcement Kit will help to strengthen the channel of your mower, making it more durable and resistant to damage.

FormNo.3360-816RevA
ChannelReinforcementKit
Z400ZMasterMowers
ModelNo.112–8673
InstallationInstructions
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
1
InstallingtheChannelPlates
Partsneededforthisprocedure:
1
Smallchannelplate
4
Bolt(1/2x3–1/2inches)
4
Flangedlocknut(1/2inch)
Procedure
1.DisengagethePTO,movethemotioncontrollevers
totheneutrallockedpositionandsettheparking
brake.
2.Stoptheengine,removethekey,andwaitforall
movingpartstostopbeforeleavingtheoperating
position.
3.Loosenthelugnutsorboltsonthereartires
(Figure1).
4.Raisethemachinesothereartiresareofftheground
andsupportthemachinewithjackstands.
5.Removethelugnutsorboltsandreartiresfromthe
machine(Figure1).
6.Removethebrakebandboltsandremovethebrake
bandfromthewheelhub(Figure1).
7.Removethecotterpinfromtheaxlenutandremove
theaxlenutandwasher(Figure1).
8.Pullthewheelhubfromthewheelmotor(Figure1).
Thismayrequiretheuseofapulleypullertoremove
it.
9.Ifneeded,removethehydrauliclinesconnectedto
thewheelmotor(Figure1).Raisetheendsabovethe
hydraulictanktopreventtheuidrunningoutand
plugthehydrauliclines.
10.Removetheretainerpinfromtheyokeatthetopof
thebrakelinkage(Figure1).
11.Removethebolts,washersandnutsholdingthe
wheelmotortotheframeandremovethewheel
motorandbrakeassembly(Figure1).
Note:Rememberthepositionofthespacers.The
longspacersareusedfortherearboltsandtheshort
spacersareusedforthefrontbolts.
12.Placethesmallchannelplateinsidetheframe
channel(Figure2).
13.Installthesmallchannelplate,wheelmotor,and
brakeassemblytotheframewiththe2shortand
longspacers,4angedlocknuts(1/2inch),and4
bolts(1/2x3-1/2inches)(Figure2).Ensurethe
spacersareinstalledinthecorrectposition.
14.Torquetheboltsbetween92to108ft-lb(125to146
N-m)
15.Connectthehydrauliclinestothewheelmotorif
removedearlier(Figure2).
16.Installthewheelhubtothewheelmotorwiththe
washerandslottednut(Figure2).
©2008—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.
OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved
Figure1
1.Brakeband
5.Slottednut
9.Washers13.Retainerpin
2.Brakebandbolts
6.Cotterpin
10.Nuts14.Wheelmotor
3.Wheelhub
7.Hydrauliclines(removeif
needed)
11.Longspacer
15.Shortspacer
4.Washer8.Wheelmotorbolts
12.Yokeatthetopofthebrake
linkage
2
Figure2
1.Longspacer
5.Wheelmotorbolt(1/2x3-1/2
inches)
9.Hydrauliclines(installif
removed)
13.Cotterpin
2.Yokeatthetopofthebrake
linkage
6.Channel
10.Wheelhub14.Brakeband
3.Retainerpin
7.Smallchannelplate
11.Washer15.Brakebandbolts
4.Shortspacer8.Flangedlocknut(1/2inch)12.Slottednut
16.Key
3
17.Torquetheslottednutto125ft-lb(170N-m)
(Figure3).
18.Checkthedistancefrombottomofslotinnutto
insideedgeofhole.Twothreadsorlessshouldbe
showing(Figure3).
19.Ifmorethantwothreadsareshowingremovenut
andinstallwasherbetweenhubandnut.
20.Tightenthenutuntilthenextsetofslotslineup
withtheholeintheshaft(Figure3).
21.Replacethecotterpin(Figure2).
Figure3
1.SlottedNut3.Holeinthreadedshaft
2.Twothreadsorless
showing
4.Washer(ifneeded)
22.Installthetirewithwheelnutsorboltstothe
machine(Figure1).
Torquethewheelnutsto95ft-lb(128N-m).
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Toro Channel Reinforcement Kit, Z400 Z Master Mower Installation guide

Toro
Brand
Toro
Model
Channel Reinforcement Kit, Z400 Z Master Mower
Category
Car kits
Type
Installation guide

Toro Channel Reinforcement Kit, Z400 Z Master Mower is a device designed to reinforce the channel of your Z400 Z Master Mower. It comes with all the necessary parts and detailed instructions to help you install it easily. The kit includes a small channel plate, bolts, flanged lock nuts, and spacers. The long spacers are used for the rear bolts, and the short spacers are used for the front bolts.

Once installed, the Toro Channel Reinforcement Kit will help to strengthen the channel of your mower, making it more durable and resistant to damage.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents