Toro Wheel Spacer Kit, Z Master Mower Installation guide

Toro
Brand
Toro
Model
Wheel Spacer Kit, Z Master Mower
Category
Car kits
Type
Installation guide

Toro Wheel Spacer Kit, Z Master Mower is designed to enhance the functionality of your Z Master Mower with a 72in/182cm cutting unit. This kit allows you to easily adjust the wheelbase of your mower, providing greater stability and improved performance in challenging mowing conditions. By increasing the distance between the wheels, the kit enhances the mower's ability to handle uneven terrain, slopes, and obstacles, resulting in a more efficient and precise mowing experience.

Toro Wheel Spacer Kit, Z Master Mower is designed to enhance the functionality of your Z Master Mower with a 72in/182cm cutting unit. This kit allows you to easily adjust the wheelbase of your mower, providing greater stability and improved performance in challenging mowing conditions. By increasing the distance between the wheels, the kit enhances the mower's ability to handle uneven terrain, slopes, and obstacles, resulting in a more efficient and precise mowing experience.

Form No. 3356-577 Rev A
Wheel Spacer Kit
For Z Master Mower with 72in/182cm Cutting Unit
Model No. 112–8699
Installation Instructions
Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.
Step
1
Installing the Channel Plates
Parts needed for this step:
4
Short spacer
4 Long spacer
8
Bolt (1/2 x 6 inches)
8
Square nut (1/2 inch)
8
Lock washer (1/2 inch)
Procedure
1. Diseng ag e the PTO , mo v e the motion control
lev ers to the neutral loc k ed position and set
the parking brak e .
2. Stop the engine , remo v e the k ey , and w ait for
all mo ving par ts to stop before lea ving the
operating position.
3. Loosen the lug n uts or bolts on the rear tires
( Figure 1 ).
4. Raise the mac hine so the rear tires are off the
g round and suppor t the mac hine with jac k
stands .
5. R emo v e the lug n uts or bolts and rear tires
from the mac hine ( Figure 1 ).
6. R emo v e the brak e band bolts and remo v e the
brak e band from the wheel hub ( Figure 1 ).
7. R emo v e the cotter pin from the axle n ut and
remo v e the axle n ut and w asher ( Figure 1 ).
8. Pull the wheel hub from the wheel motor
( Figure 1 ). T his ma y require the use of a pulley
puller to remo v e it.
Mak e sure the w oodr uff k ey remains with the
wheel motor shaft.
9. R emo v e the h y draulic lines connected to the
wheel motor ( Figure 1 ). Raise the ends abo v e
the h y draulic tank to prev ent the fluid r unning
out and plug the h y draulic lines .
10. R emo v e the retainer pin from the y ok e at the
top of the brak e linkag e ( Figure 1 ).
Note: R emember the position of the spacers .
T he long spacers are used for the rear bolts and
the shor t spacers are used for the front bolts .
11. R emo v e the bolts , spacers , w ashers and n uts
holding the wheel motor to the frame and
remo v e the wheel motor and brak e assembly
( Figure 1 ). Discard the spacers .
12. Install the wheel motor and brak e assembly
to the frame with the 2 new shor t and long
spacers , 4 square n uts (1/2 inc h), 4 loc k
w ashers (1/2 inc h) and 4 bolts (1/2 x 6 inc hes)
( Figure 2 ). Ensure the spacers are installed in
the cor rect position.
13. T or que the bolts to 75 ft-lb (102 N ⋅ m).
14. Connect the h y draulic lines to the wheel motor
( Figure 2 ).
15. Install the wheel hub to the wheel motor with
the w oodr uff k ey , w asher , and slotted n ut
( Figure 2 ).
© 2006—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Register at www.Toro.com. Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Figure 1
1. Brake band
6. Cotter pin
11. Long spacer
16. Z597 Diesel brake linkage
shown
2. Brake band bolts 7. Hydraulic lines 12. Yoke at the top of the brake
linkage
17. Woodruff key
3. Wheel hub 8. Wheel motor bolts
13. Retainer pin
4. Washer 9. Washers 14. Wheel motor
5. Slotted nut
10. Nuts
15. Short spacer
2
Figure 2
1. New long spacer
5. Bolt (1/2 x 6 inches)
9. Hydraulic lines
13. Cotter pin
2. Yoke at the top of the brake
linkage
6. Channel 10. Wheel hub 14. Brake band
3. Retainer pin
7. Square nut (1/2 inch)
11. Washer 15. Brake band bolts
4. New short spacer
8. Lock washers (1/2 inch)
12. Slotted nut 16. Woodruff key
3
16. T or que the slotted n ut to 125 ft-lb (170 N ⋅ m)
( Figure 3 ).
17. Chec k the distance from bottom of slot in n ut
to inside edg e of hole . T w o threads or less
should be sho wing ( Figure 3 ).
18. If more than tw o threads are sho wing remo v e
n ut and install w asher betw een hub and n ut.
19. Tighten the n ut until the next set of slots line
up with the hole in the shaft ( Figure 3 ).
20. R e place the cotter pin ( Figure 2 ).
Figure 3
1. Slotted Nut 3. Hole in threaded shaft
2. Two threads or less
showing
4. Washer (if needed)
21. Install the tire with wheel n uts or bolts to the
mac hine ( Figure 1 ).
T or que the wheel n uts to 95 ft-lb (128 N·m).
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Toro Wheel Spacer Kit, Z Master Mower Installation guide

Toro
Brand
Toro
Model
Wheel Spacer Kit, Z Master Mower
Category
Car kits
Type
Installation guide

Toro Wheel Spacer Kit, Z Master Mower is designed to enhance the functionality of your Z Master Mower with a 72in/182cm cutting unit. This kit allows you to easily adjust the wheelbase of your mower, providing greater stability and improved performance in challenging mowing conditions. By increasing the distance between the wheels, the kit enhances the mower's ability to handle uneven terrain, slopes, and obstacles, resulting in a more efficient and precise mowing experience.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents