Bradley Corporation S19-220B Installation guide

Bradley Corporation
Brand
Bradley Corporation
Model
S19-220B
Category
Wall & ceiling mounts accessories
Type
Installation guide
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX (262) 251-5817
http://www.bradleycorp.com
215-158E Rev. J; EN 06-532E
© 2007 Bradley Corporation
Page 1 of 8 5/14/07
E19-220
Wall-Mounted Eyewash with
Plastic Bowl
E19-220B
Wall-Mounted Eyewash with
Stainless Steel Bowl
E19-220DC
Wall-Mounted Eyewash with
Dust Cover
E19-220FW
Wall-Mounted Eye/Face Wash
with Plastic Bowl
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . 2
Installation Instructions . . . . . . . . . . . . . . . . . . 3
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . .3–4
E19-220 Components and Parts List . . . . . . . . 5
E19-220B Components and Parts List . . . . . . 6
E19-220DC Components and Parts List . . . . . 7
E19-220FW Components and Parts List . . . . . 8
Installation
E19-220
E19-220DC
E19-220B
E19-220FW
2
E19-220, E19-220B, E19-220FW, E19-220DC Installation
5/14/07 Bradley Corporation • 215-158E Rev. J; EN 06-532E
WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the
installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to
the eyewash should be “ON” at all times. Provisions shall be made to prevent
unauthorized shutoff.
The ANSI Z358.1 standard requires an uninterruptable supply of flushing fluid at
a minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per
ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to
ensure compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment
per ANSI Z358.1.
For questions regarding the operation or installation of this product, visit
www.bradleycorp.com or call 1-800-BRADLEY.
Product warranties may also be found under ”Product Information” on our web
site at www.bradleycorp.com.
Installation
T
H
IS
S
ID
E
U
P
Packing List
P
.O
. B
o
x
3
0
9
, M
e
n
o
m
o
n
e
e
F
a
lls
, W
I 5
3
0
5
1
R
T
E
S
T
T
H
I
S
U
N
I
T
E
A
C
H
W
E
E
K
Test-operate valve(s) each week and sign below
.
R
eport any m
alfunctions imm
ediately.
Ven
til(e) w
öche
ntlich im
Testbe
trieb prüfen
, bestätig
t
durch U
ntersch
rift. Jeg
liche Störung sofort m
eld
en.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
D
I
E
S
E
S
G
E
R
Ä
T
1
S
T
W
Ö
C
H
E
N
T
L
I
C
H
Z
U
P
R
Ü
F
E
N
.
E
S
S
A
I
H
E
B
D
O
M
A
D
A
I
R
E
Test le fonctionnem
ent des va
lves chaque se
m
ain
e et
signe en bas. S
'il y à quelque chose q
u
i ne va pas fait
un rapport im
médiatem
ent.
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
114-051
3
Installation E19-220, E19-220B, E19-220FW, E19-220DC
Bradley Corporation • 215-158E Rev. J; EN 06-532E 5/14/07
Installation
Supplies Required:
• (3) 8m wall fasteners and bolts
• Pipe sealant
• Piping to 1/2" BSP water supply inlet on
unit
• Piping to 1-1/4 - 11 BSP drain outlet for
eyewash
• Sign-mounting hardware
Step 1: Install inlet drain fittings
NOTE: The top of the eyewash heads should
be 1067mm (42") from the floor.
1. Position the inlet drain fitting over the 1-
1/4" drain outlet pipe from wall.
2. Using the inlet drain fitting as template,
mark bolt hole locations on the wall OR
install three suitable fasteners (supplied
by installer) for 8m bolts in the wall at
marked hole locations (see illustrations
on pages 3–4).
3. Bolt the inlet drain fitting to the wall or
wall fasteners using 8m bolts (supplied
by installer).
4. After the inlet drain is secured, assemble
the flag handle, washer and nut.
Step 2: Connect water supply
1. Connect the water supply piping (supplied by installer) to the 1/2" BSP inlet on the eyewash.
2. Connect the drain piping (supplied by installer) to the 1-1/4 - 11 BSP drain outlet on the
eyewash.
3. Mount the safety sign to the wall or pipe using sign-mounting hardware (supplied by installer).
4. Open the water supply lines. Test for leaks and adequate water flow.
394mm (15-1/2")
184mm
(7-1/4")
57mm
(2-1/4")
133mm
(5-1/4")
Ø 8mm
(5/16")
337mm
(13-1/4")
Ø 254mm (10")
102mm
(4")
210mm
(8-1/4")
119mm
(4-5/8")
1067mm (42")
Suggested
Height
To Floor
927mm
(36-1/2")
Suggested
Height
To Floor
Wall
E19-220
902mm
(35-1/2")
Suggested
Height
To Floor
394mm (15-1/2")
206mm
(8-1/8")
57mm
(2-1/4")
133mm
(5-1/4")
102mm
(4")
Ø 8mm
(5/16")
210mm
(8-1/4")
119mm
(4-5/8")
Ø 254mm (10")
337mm
(13-1/4")
1067mm
(42")
Suggested
Height
To Floor
Wall
Ø 273mm (10-3/4")
184mm
(7-1/4")
425mm
(16-3/4")
222mm
(8-3/4")
133mm
(5-1/4")
346mm
(13-5/8")
102mm
(4")
Wall
508mm (20")
210mm
(8-1/4")
119mm
(4-5/8")
1067mm
(42")
Suggested
Height
To Floor
57mm
(2-1/4")
Ø 8mm
(5/16")
927mm
(36-1/2")
Suggested
Height
To Floor
403mm (15-7/8")
187mm
(7-3/8")
102mm
(4")
346mm
(13-5/8")
Ø 273mm (10-3/4")
927mm
(36-1/2")
Suggested
Height
To Floor
Wall
57mm
(2-1/4")
133mm
(5-1/4")
Ø 8mm
(5/16")
119mm
(4-5/8")
1067mm
(42")
Suggested
Height
To Floor
210mm
(8-1/4")
4
E19-220, E19-220B, E19-220FW, E19-220DC Installation
5/14/07 Bradley Corporation • 215-158E Rev. J; EN 06-532E
E19-220BE19-220DC
E19-220FW
5
Installation E19-220, E19-220B, E19-220FW, E19-220DC
Bradley Corporation • 215-158E Rev. J; EN 06-532E 5/14/07
Assembly of Components - E19-220 (with Plastic Bowl)
1.6
1.5
Flow Control
This End
1.4
1.3
1.2
1.1
1-1/4" - 11 BSP
Drain Outlet
1.8
1.7
1
1/2" BSP Supply
Inlet (BSP threads
are noted with
black line on
threads)
1.9
1.10
1.11
1.111
2
1.12
P.O. Box 309, Menomonee Falls, WI 53051
R
TEST THIS UNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
114-051
3
4
NOTE: Items 1.1-1.12 come preassembled as Item 1.
1 S39-243 1 Europe Eyewash Assembly
1.1 111-061BSP 1 Inlet Drain Fitting
1.2 124-028 1 Gasket
1.3 154-058 1 Plastic Eyewash Bowl
1.4 173-025 1 Cup Strainer
1.5 S21-071 1 Supply Stem
1.6 113-1185 1 Spacer, Drain
1.7 S05-091 1 Eyewash Yoke Assembly
1.8 107-371 2 Dust Cover
1.9 113-006LQ 1 Pipe 1/2" NPT x 89mm
1.10 169-025 1 Elbow
1.11 S27-282B 1 1/2" Ball Valve with nut
1.111 110-215 1 Nut only
1.12 142-002DA 1 Lockwasher
2 128-135 1 Plastic Handle
3 114-051E 1 Safety Sign
4 204-421 1 Emergency Tag
Item Part No. Qty Description
Item Part No. Qty Description
Prepack S45-1785 includes Items 1.2, 1.4, 1.5, 1.6
Prepack S45-123 includes Items 2, 1.12, 1.111
6
E19-220, E19-220B, E19-220FW, E19-220DC Installation
5/14/07 Bradley Corporation • 215-158E Rev. J; EN 06-532E
Assembly of Components - E19-220B (with Stainless Steel Bowl)
1.6
1.5
Flow Control
This End
1.4
1.3
1.2
1.1
1-1/4" - 11 BSP
Drain Outlet
1.8
1.7
1
1/2" BSP Supply
Inlet (BSP threads
are noted with
black line on
threads)
1.9
1.10
1.11
1.111
2
1.12
P.O. Box 309, Menomonee Falls, WI 53051
R
TEST THIS UNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
114-051
3
4
Figure 2b
NOTE: Items 1.1-1.12 come preassembled as Item 1.
1 S39-246 1 Europe Eyewash Assembly
1.1 111-061BSP 1 Inlet Drain Fitting
1.2 124-028 1 Gasket
1.3 187-053 1 Stainless Steel Eyewash Bowl
1.4 173-009 1 Cup Strainer
1.5 S21-071 1 Supply Stem
1.6 113-1159 1 Spacer, Drain
1.7 S05-091 1 Eyewash Yoke Assembly
1.8 107-371 2 Dust Cover
1.9 113-006LQ 1 Pipe 1/2" NPT x 89mm
1.10 169-025 1 Elbow
1.11 S27-282B 1 1/2" Ball Valve with nut
1.111 110-215 1 Nut only
1.12 142-002DA 1 Lockwasher
2 128-135 1 Plastic Handle
3 114-051E 1 Safety Sign
4 204-421 1 Emergency Tag
Item Part No. Qty Description
Item Part No. Qty Description
Prepack S45-1782 includes Items 1.2, 1.4, 1.5, 1.6
Prepack S45-123 includes Items 2, 1.12, 1.111
7
Installation E19-220, E19-220B, E19-220FW, E19-220DC
Bradley Corporation • 215-158E Rev. J; EN 06-532E 5/14/07
Assembly of Components - E19-220DC (with Dust Cover)
P.O. Box 309, Menomonee Falls, WI 53051
R
TEST THIS UNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
114-051
1.9
1.5
Flow Control
This End
1.4
1.3
1.2
1.1
1.10
1.12
6
1.14
1
7
1.11
1.8
HANDLE NOTE:
Close the cover and
put the pin through
the clip to keep closed.
1.6
1.7
1-1/4" - 11 BSP
Drain Outlet
1/2" BSP Supply
Inlet (BSP threads
are noted with
black line on
threads)
1.121
1.13
2
Figure 2c
NOTE: Items 1.1-1.14 come preassembled as Item 1.
1 S39-312 1 Europe Dust Cover/Eyewash Assy
1.1 111-061BSP 1 Inlet-Drain Fitting
1.2 124-028 1 Gasket
1.3 S90-009 1 Dust Cover Assembly
1.4 173-009 1 Cup Strainer
1.5 S21-071 1 Supply Stem
1.6 113-1159 1 Spacer, Drain
1.7 S05-091 1 Eyewash Yoke Assembly
1.8 269-447 1 Bumper
1.9 161-025 1 Hex Nut
1.10 113-006LQ 1 Pipe 1/2" NPT x 89mm
1.11 169-025 1 Elbow
1.12 S27-282B 1 1/2" Ball Valve with nut
1.121 110-215 1 Nut only
1.13 153-372R 1 Ball Valve Adapter
1.14 142-002DA 1 Lockwasher
2 S08-056 1 Handle Assembly
3 114-051E 1 Safety Sign
4 204-421 1 Emergency Tag
Item Part No. Qty Description
Item Part No. Qty Description
Prepack S45-1782 includes Items 1.2, 1.4, 1.5, 1.6
Ball Valve Kit S30-072 includes Items 1.12, 1.13, 1.14, 1.121, 2
Prepack S30-087 includes Items 1.13, 1.14, 1.121, 2
8
E19-220, E19-220B, E19-220FW, E19-220DC Installation
5/14/07 Bradley Corporation • 215-158E Rev. J; EN 06-532E
Assembly of Components - E19-220FW (with Eye/Face Wash)
2
1.12
P.O. Box 309, Menomonee Falls, WI 53051
R
TEST THIS UNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
114-051
3
4
1.6
1.5
1.4
1.3
1.2
1.1
1-1/4" - 11 BSP
Drain Outlet
1.8
1.7
1
1/2" BSP Supply
Inlet (BSP threads
are noted with
black line on
threads)
1.9
1.10
1.11
1.111
Figure 2d
NOTE: Items 1.1-1.12 come preassembled as Item 1.
1 S39-421 1 Europe Eye/Face Wash Assembly
1.1 111-061BSP 1 Inlet Drain Fitting
1.2 124-028 1 Gasket
1.3 154-058 1 Plastic Eyewash Bowl
1.4 173-025 1 Cup Strainer
1.5 113-1150 1 Supply Stem
1.6 S05-091P 1 Eyewash Yoke Assembly
1.7 S05-135 2 EFW Sparyhead Assembly
1.8 S53-063 2 Dust Cover
1.9 113-006LQ 1 Pipe 1/2" NPT x 89mm
1.10 169-025 1 Elbow
1.11 S27-282B 1 1/2" Ball Valve with nut
1.111 110-215 1 Nut only
1.12 142-002DA 1 Lockwasher
2 128-135 1 Plastic Handle
3 114-051E 1 Safety Sign
4 204-421 1 Emergency Tag
Item Part No. Qty Description
Item Part No. Qty Description
Prepack S45-123 includes Items 2, 1.12, 1.111
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Bradley Corporation S19-220B Installation guide

Bradley Corporation
Brand
Bradley Corporation
Model
S19-220B
Category
Wall & ceiling mounts accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents