Baja WD400U User manual

WD400U Service Manual

For any questions please contact Baja Motorsports at 888-863-2252

1

Content

Content..................................................................................................................................................2

Chapter I General description...............................................................................................................5

Section 1 Special tools, instruments & meters.................................................................................... 6

(I) Special tools.........................................................................................................................7

Section 2 Identication code, label of model and engine No...............................................................8

Section 3 Points for attention in maintenance......................................................................................8

Section 4 Specication...................................................................................................................... 12

I. How to use conversion table of unit................................................................................... 12

(1) How to use conversion table............................................................................................ 12

(2) Denition of unit...............................................................................................................12

II. Basic specication.............................................................................................................13

III. ATV body......................................................................................................................... 15

IV. Electric system................................................................................................................. 16

V. Maintenance specication of engine................................................................................. 17

Section 5 Requirements for torque of fastener................................................................................... 20

(3) General torque specication............................................................................................ 22

Section 6 Lubrication point and type of lubricants............................................................................ 23

(I) ATV body......................................................................................................................... 23

(II) Engine............................................................................................................................. 24

Chapter II Maintenance and adjustment of vehicle............................................................................ 25

Section 1 Periodic maintenance/lubrication...................................................................................... 25

Section 2 Disassembly and assembly of cushion, fender and fuel tank............................................. 26

(I) Cushion...............................................................................................................................26

(II) Rear fender...................................................................................................................... 26

(III) Fuel tank.......................................................................................................................... 29

(IV) Front fender..................................................................................................................... 30

Section 3 Maintenance and adjustment of vehicle body.................................................................... 32

(I) Wear inspection of front and rear brake............................................................................ 32

(II) Adjustment of front brake..................................................................................................32

(III) Adjustment of free clearance of left lever and rear brake pedal.......................................33

(IV) Position adjustment of steering lever............................................................................. 35

(V) Lubricating oil level inspection of rear driving gearcase................................................. 35

(VI) Replacement of engine oil of rear driving gearcase....................................................... 36

(VII) Rubber sleeve inspection of rear wheel fork................................................................. 37

(VIII) Inspection of steering system....................................................................................... 37

(IX) Adjustment of toe-in of front wheel............................................................................... 38

(X) Inspection of front/rear shock absorber........................................................................... 39

(XI) Adjustment of rear shock absorber............................................................................... 39

(XII) Inspection of tire.......................................................................................................... 40

(XIII) Inspection of rim........................................................................................................ 41

Section 4 Maintenance and adjustment of electrical appliance......................................................... 42

(I) Inspection of battery......................................................................................................... 42

(II) Inspection of fuse............................................................................................................ 43

(III) Replacement of headlight lamp.......................................................................................44

2

Section 5 Maintenance and adjustment of engine.............................................................................. 46

(I) Cleaning of air lter...........................................................................................................46

(II) Inspection of spark plug.................................................................................................. 47

(III) Adjustment of idle speed............................................................................................... 48

(IV) Adjustment of free clearance of throttle grip................................................................ 48

(V) Adjustment of speed limiter............................................................................................ 49

(VI) Adjustment of valve clearance..................................................................................... 50

(VII) Adjustment of timing chain tension..............................................................................52

(VIII) Measuring of compressive force................................................................................. 53

(IX) Inspection oil quantity of engine................................................................................... 54

(X) Replacement of engine oil and inspection of oil ow..................................................... 55

Chapter III Repair and maintenance of vehicle body.........................................................................57

Section 1 Rear driving gearcase and driving shaft.............................................................................57

(I) Troubleshooting.................................................................................................................58

(II) Inspection.........................................................................................................................58

(III) Troubleshooting table.....................................................................................................59

(IV) Disassembly.................................................................................................................. 60

(V) Inspection.........................................................................................................................63

Section 2 Rear wheel/Rear brake/Rear wheel axle............................................................................ 64

(I) Removal steps................................................................................................................... 66

(II) Inspection stepes............................................................................................................ .68

(III) Installation steps............................................................................................................. 70

Section 3 Rear shock absorber and rear wheel fork.......................................................................... 74

(I) Disassembling steps......................................................................................................... 75

(II) Checking steps................................................................................................................ 77

(III) Mounting steps.............................................................................................................. 79

Section 4 Steering operation system................................................................................................. 82

(I) Removal steps of steering bar........................................................................................... 83

(II) Removal steps of steering vertical column welding....................................................... 84

(III) Inspection content......................................................................................................... 85

(IV) Installation steps........................................................................................................... 86

(V) Installation steps of steering bar.................................................................................... 89

Section 5 Front Wheel and Front brake.............................................................................................90

(I) Disassembly......................................................................................................................92

(II) Installation.......................................................................................................................93

Section 6 Front shock absorber and front wheel fork and Front differential.................................. 95

(I) Disassembly.................................................................................................................... 97

(II) Installment steps.......................................................................................................... 100

Chapter IV Electric appliance........................................................................................................ 102

Section 1 Electric assembly............................................................................................................ 102

Section 2 Inspect switch................................................................................................................. 104

Section 3 Check headlight lamp..................................................................................................... 105

Section 4 Troubleshooting the ignition system failure................................................................... 106

Section 5 Running starting circuit.................................................................................................. 108

3

Section 6 Troubleshooting electric starting system......................................................................... 109

Section 7 Battery will not hold charge............................................................................................. 112

Section 8 Troubleshooting................................................................................................................ 114

Section 9 Inspection of lighting system........................................................................................... 116

(I) Headlight not working..................................................................................................... 116

(II) Taillight not working...................................................................................................... 117

Section 10 Troubleshooting.............................................................................................................. 118

(I) If indicated lamp is out of work....................................................................................... 118

Section 11 Inspection of signal system........................................................................................... 120

(I) If the neutral indicated lamp is out work......................................................................... 120

(II) If the reverse indicated lamp is out work........................................................................ 121

(III) If the HB indicated lamp is out work............................................................................ 122

Chapter V Engine.............................................................................................................................. 123

Section 1 Disassembly of Engine...................................................................................................... 123

(I) Remove the engine from nished ATV.............................................................................. 123

(II) Disassembly of engine..................................................................................................... 145

Section 2 Inspection and maintanence of engine............................................................................... 135

Section 3 Assembly and adjustment of engine................................................................................... 154

(I) Installation......................................................................................................................... 183

Chapter VI Vehicle Troubleshooting.................................................................................................. 180

(I) Starting trouble/difculty................................................................................................... 180

4

Chapter I General Description

Section 1 Description

1. Front wheel

2. Headlight

3. Forward/Reverse lever

4. Shift pedal

5. Fuel valve

6. Hand-operated lever

7. Air choke

8. Taillight

9. Rear wheel

10. Rear luggage carrier

11. Exhaust silencer

12. Cushion

13. Fuel tank cover

14. Rear brake pedal

15. Front luggage carrier

16. Left rear brake lever

17. Hand-operated parking brake

18. Main switch lock

19. Throttle grip

20. Right front brake lever

21. Left switch unit

22. Left and right mirror (not

shown)

CAUTION:

The ATV you purchased may be slightly different from the pictures in the

manual due to improvements.

1

2

3

4

5

6 7

8

9

10

11 12 13

14 15

16 17

18

19

20

21

5

Section 1 Special tools, instruments and meters

(I) Special tools

There are special tools needed to properly adjust and assemble this unit. These tools are

intended to prevent maintenance defects and damage.

1. Wrench for valve adjustment, mainly used to adjusting the valve clearance. Specication:

3mm, 90890-01311

2. Puller for piston pin, used for removing piston pin.

3. Remover for rotator, mainly for pulling the magneto rotator from crank.

4. Clamp for rotator, for clamping magneto rotator when removing it to prevent it’s rotation due

to torque force.

5. Stop rotating meter for rotator, used for removing and assembling rotator of kick starter.

6. Puller for crank, for disassembling crank from crankcase.

7. Puller for rocker shaft, used for the removing rocker shaft.

8. Compressing tools for spring of valve, for xing and compressing spring when assembling

valve lock clamp.

9. Assembling and disassembling tools for valve guide.

10. Assembling buffer, used for assembling crank and balancing gear.

11. Hollow sleeve, for assembling crank and balancing gear.

12. Assembling tool for crank, used for assembling crank and balancing gear.

13. Assembling and disassembling joint for universal coupling.

14. Assembling and disassembling disc, used for assembling and disassembling reverse gear.

15. Fixed puller for gear.

6

(II) Instruments and meters

The following instruments and meters can be selected with

reference to the same type of vehicle.

7

Section 2 Identication code, label

of model and engine No.

Identication code

Engraved in the left or right side of the front

supporting main tube of engine of frame

Engine No.

This is engraved on the top middle part of the

right crankcase of engine.

Section 3 Points for attention in maintenance

1. Preparation when disassembling

• Clean and dirt or mud from vehicle.

• Be sure to use proper tools when disassembling

• Keep all the components away from re. Pay attention to hot surfaces such as the engine,

exhaust etc.

• When disassembling the ATV, keep alike parts such as gear pairs, cylinder, piston, etc.

together. When assembling or replacing these components they should be kept in pairs.

• When disassembling the engine, clean all components and place in a tray in the order of

disassembly, not only increasing the assembling speed, but also ensuring the correct assembly.

2. Replace the components

When replacing components use only the products, lubricants and grease recommended by

manufacturer.

3. Oil seal, shim, O-ring, clip, split pin, elastic washer

• When disassembling to maintain the engine, to ensure that the reassembled engine has good

sealing and connected parts are xed and reliable, the oil seal, shim, o-ring, clip, split pin and

elastic washer should be replaced, be sure to keep lip of oil seal, surface of shim and o-ring in a

clean condition.

• When reassembling, apply lubricant to all the alike components and bearings,

apply grease for oil seal.

8

4. Clip

Before assembling, check all the clips carefully.

Replace with a new one after removing from piston

pin. When mounting clip ring (1), make the sharp

end face (2) on the opposite position of

impacted face (3) of clip. (see gure at left)

5. Locking washer/shim and location pin

When reassembling, replace all locking washer/shim

and location pin (a) . After bolt or nut is in the lock

position, bend and x both ends of locking shim

along head of bolt or direction of nut.

6. Bearing and oil seal

When assembling bearing and oil seal, put the mark

(specication of manufacturer) outside. When as-

sembling oil seal, apply a thin layer of lithium-based

grease on the lip of oil seal.

CAUTION:

Do not dry inside of bearing by blowing out with

compressed air, this will cause damage to the surface

of the bearing.

9

7. Check of electric parts

Make sure there is no rust, dirt or moisture at the

connection, if there is blow it dry or clean.

The electrolyte inside the battery is corrosive, take

extra precautions as to not get this on your body.

When repairing wires on electrical parts, remove

the wire on the terminal of negative pole of battery

(see gure 7.1). When tightening or loosening bolt

on terminal of battery, do not let the wrench contact

the engine or other metal parts of the vehicle body to

avoid electric shock.

When connecting the wire to battery, rst connect

the positive pole then connect the negative pole.

After wires are connected, apply clean grease on the

terminal to increase resistance of rust.

Check the terminal of connector

A. Grip the two terminals of connector together,

check with the multimeter (see gures 7.3 and 7.4)

10

B. If there is slack in the joint, bend the plug pin

upward, then connect with connector plug (see gure

7.5)

Before mounting the new fuse, check if the load of

fuse on the components are correct, especially the

portion being broken regularly, then mount the fuse

having proper current value.

There are two kinds of wire connectors, a single-

head connector, another a multi-head connector.

Before connecting single-head connector, make sure

there are no defects on the housing of the joints.

When inserting the joint, after defects are xed, put

plastic coating on.

In general, multi-head connectors are plastic and

designed to lock. When disassembling the connector,

rst open lock; when connecting again make sure the

joints are in good condition and there are no bends

or twists. After connecting, align the lock device and

lock.

8. Use torque spanner to tighten screw and nut, and

as per specied torque. It should be tightened in

steps from big to small, from inside to outside and

along the direction of a diagonal line that intersects

(see gure 8.1).

11

   Section4Specication

I. How to use conversion table of unit

(1) How to use a conversion table

All the specied documents in this manual are taken SI and Metric as unit. With the following

conversion table, metric unit could ne conversed into imperial unit.

Metric Multiply Imperial

mm 0.03937 in

2mm x 0.03937 = 0.08in

Conversion Table

Known Unit Multiply Product

Torque m•kg

m•kg

cm•kg

7.233

86.794

0.0723

0.8679

ft.lb

in•lb

ft•lb

in•lb

Weight kg

g

2.205

0.03527

lb

oz

Length km/hr

km

m

cm

mm

06.214

0.6214

3.281

1.094

0.3937

0.03937

mph

mi

ft

yd

in

Volume/capacity cc(cm³)

cc(cm²)

lit(liter)

0.03527

0.06102

0.8799

0.2199

oz(IMP lig.)

cu•in

qt(IMP lig.)

gal(IMP liq.)

Others kg/mm

kg/cm²

Centrigrade

55.997

14.2234

9/5(˚C)+32

lb/in

psi(lb/in2)

Fahrenheit(˚F)

Unit Read Denition Measurement

mm

cm

Millimeter

Centimeter

10ֿ³Meter

10ֿ²Meter

Length

kg kilogram 10³Gram Weight

N Newton 1 lilo x meter/second Force

Nm

m•kg

Newton meter

Meter kilogram

Newton x meter

Meter x kilo

Torque

Pa

N/mm

Pascal

Newton per millimeter

Newton x meter²

Newton/centimeter

Pressure

Rigid of spring

L

cm³

Liter

Cubic centimeter ¯ ¯

r/min Revolutions per minute − Rotational speed

(2) Denition of unit

12

II.Basicspecication

Dimensions:

Overall length

Overall width

Overall height

Seat height

Wheel base

Ground clearance

Minimum turning radius

Shaft drive

75.5in

41in

44in

35.25in

49in

7.75in

118.1in

Weight with oil and fuel

573lbs.

Engine:

Type

Cylinder arrangement

Displacement

Bore and stroke

Compression ratio

Starting system

Lubrication system

Oil cooled 4-stroke

Forward-inclined single cylinder

387cc

83*71.6mm

9.50:1

Electronic ignition with recoil

Wet sump

Final gear case oil:

Type

Quantity

SAE80 API GL-4 Hypoid gear oil

0.23L (0.24 US qt.)

Differential gear case oil:

Type

Quantity

SAE80 API GL-4 Hypoid gear oil

0.35L (0.37 US qt.)

Airlter

Wet element

Fuel:

Type

Fuel tank capacity

Fuel reserve amount

UNLEADED GASOLINE ONLY

13.5L (3.57 US gal)

3.3L (0.87 US gal)

Carburetor:

Type PD33G

Spark plug:

Type

Gap

DR8EA/NGK

0.6-0.7mm (0.02-0.03in)

Clutch type Dry centrifugal automatic

Transmission:

Primary reduction system

Secondary reduction system

Secondary reduction ratio

Transmission type

Operation

Forward gear

Reverse gear

V-belt

Shaft drive

41/21 24/1 33/9 (9.545)

V-belt automatic

Left hand operation

35/20 (1.750)

26/15 (1.733)

13

Chassis:

Frame type

Caster angle

Trail

Steel tube frame

4

21mm (0.83in.)

Tire:

Type

Size

Tubeless

AT25 8-12

AT25 10-2

Brake:

Front brake type

operation

Rear brake type

operation

Dual disc brake

Right hand operation

Drum brake

Left hand and right foot operation

Suspension:

Front

Rear

Double wishbone

Swing arm (mono cross)

Shock absorber:

Front

Rear

Coil spring/oil damper

Wheel travel:

Front

Rear

160mm (6.30in)

180mm (7.09in)

Electrical:

Ignition system

Generator

Battery type

Battery capacity

DC-C.D.I.

A.C. magneto

YTX14AH

12V, 12Ah

Headlight type:

Krypton bulb

Bulb voltage, wattage capacity:

Headlight

Tail/brake light

Neutral light indicator

Reverse indicator light

Oil temperature warning light

Four-wheel drive indicator light

12V, 30/30W2

12V, 5/21W1

12V, 1.7W1

Fuses:

Main fuse

Headlight fuse

Ignition fuse

Four-wheel drive fuse

Signaling system fuse

30A

15A

3A

10A

14

III. ATV body

Item Standard Limit

Steering system

Type of steering bearing

Powder metallurgy sliding

bearing

Type Rim, tubeless tire

Material of rim Steel plate

Size of tire AT25x8-12

Size of rim AT 12x8

Type Hydraulic disc

Type Spoke rim, tubeless tire

Material of rim Steel plate

Sixe of tire AT22x10-10

Size of rim AT 10x8.0

Type Drum type

Thickness of friction piece 4.0mm (0.16in) 2.0mm

Free length of back spring of brake

shoe

71.0mm (2.77in)

Free play of brake lever (left) 5-7mm (0.195-0.273in)

Free play of brake lever (right) 5-7mm (0.195-0.273in)

Free play of rear brake pedal 20-30mm (.78-1.17in)

Free play of throttle grip 3-5mm (0.117-0.273in)

Front

Wheel

Front Brake

Rear

Wheel

Rear

Brake

Brake lever

and brake

pedal

15

Item Standard

Voltage of electric system 12V

Type

DR8EA/NGK

Resistence 10Ω

Clearance of spark plug 0.6-0.7mm (0.023-0.027in)

Resistence of primary coil At 20°C(68˚F), 0.5-1.5Ω

Resistence of secondary coil At 20°C(68°F), 10.3-12.2Ω

Clearance of min. spark 6mm(0.24in)

Spark plug

Ignition coil

IV. Electric system

Item Standard

Resistence of induction coil/color At 20˚C (68˚F), 189-231Ω Blue-black

Resistence of source coil/color At 20˚C (68˚F), 470-530Ω yellow/green-red

Type of C.D.I. Electric capacity contactless type

No-loading adjusting voltage 14.1-14.9V

Voltage-resisting value 200V

Type A·C magneto

Rated output voltage At 2000r/min 14-15V

Coil resistence/color At 20˚C (68˚F) 0.7-1.8 white-white

Specic gravity 1.28

Type/capacity 12N14-BS/12V, 14Ah

Type Fuse

Main fuse 30A

Ignition fuse 15A

Coil resistence At 20˚C (68˚F), 72-88Ω

Diode Yes

Type Constant mesh type

Output power 0.35KW

Resistence of armature coils At 20˚C (68˚F), 0.003-0.0048Ω

Ampere 100A

coils resistence At 20˚C (68˚F), 4.8-5.3Ω

Magneto

Rectier

Charging

system

Battery

Broken

circuit of

system

Relay of cut-

off current

Electric start-

ing motor

system

Electric

starting relay

system

16

V.MaintenanceSpecicationofEngine

Item Standard Limit

Axle Drive

Meshing clearance of last end gear

Meshing clearance of middle gear (forward)

Meshing clearance of middle gear (backward)

0.1-0.2mm (0.004-0.008in)

0.1-0.25mm (0.004-0.01in)

Lubrication system:

Type of oil lter

Type of oil pump

Clearance of side

Endface clearance “A” or “B”

Releasing pressure of safety valve

Wire lter net

Rotor type, pressure splash type lubrication

0.04-0.09mm (0.0015-0.0351in)

0.15mm (0.006in)

80-120Kpa

0.09mm

0.20mm

Cylinder

Bore size

70.97-71.02mm (2.768-2.77in)

(Distance between measuring point and

upper endface of cylinder is 40mm) 80.50mm

Cylinder head

Flatness of lower endface

Measure the surface warp of every portion

on the lower endface of cylinder head with

ruler.

0.10mm

Timing chain

Type of timing chain

Tension type of timing chain

Roller chain

Free adjustment

Pneumatic camshaft:

Driving method

Roundness tolerance of camshaft

Outside diameter of camshaft

Cam size

Exhaust: A

B

Intake: A

B

Chain driven

24.96-24.98mm

40.38mm (1.574in)

32.18mm (1.255in)

40.55mm (1.581in)

0.03mm

Rocker arm/ Rocker arm shaft

Outside diameter of shaft

Inside diameter of rocker arm

Clearance between arm and shaft

11.981-11.991

12.000-12.018

0.009-0.037

17

Item Standard Limit

Valve spring:

Outside spring:

Free length: intake/exhaust

Setting length when valve is closed:

Compressing pressure when assembling:intake/exhaust

Limit value of sqaureness:intake/exhaust

Twisting direction of spring (top view):intake/exhaust

37.2mm (1.45in)

32.0mm (1.25in)

162.8-200.1N

clockwise

2.5˚/1.6mm

Valve, valve seal, valve guide

Valve clearance (it’s cold): intake

exhaust

Size of valve

A-diameter of valve head exhaust

intake

B-width of valve face intake/exhaust

C-width of valve set intake/exhaust

D-limit thickness intake/exhaust

Outside diameters of valve stem exhaust

intake

Inside diameter of valve guide: intake/exhaust

Clearance between valve stem and guide:

exhaust

intake

Roundness of valve seem

0.02-0.03mm(0.00078-.00117in)

0.03-0.05mm(0.00117-0.00195in)

33.93mm(1.32in)

40mm(1.56in)

3.19mm/3.45mm(0.124-0.135in)

0.6mm/1.03mm(0.023-0.040in)

1.18mm/0.98mm(0.046-0.038in)

6.94-6.91mm(0.271-0.269in)

6.93-6.89mm0.270-0.269in)

6.000-6.012mm(0.234in)

0.025-0.052mm(.001-.002in)

0.10-0.037mm(0.0039-0.0014in)

1.6mm

0.10mm

0.08mm

0.03mm

Piston ring:

First ring

Type

Size (BxT)

Type

Size (BxT)

Bucket-shaped back round

1.11x3.33mm(0.043-0.13in)

Flat type

1.45x3.33mm(0.057-0.130in)

2.74x2.48mm(0.107-0.097in)

0.4mm

0.12mm

0.4mm

0.12mm

V.MaintenanceSpecicationofEngine

18

V.MaintenanceSpecicationofEngine

Item Standard Limit

Piston

Piston size “D”

Measuring point “H” (from bottom line of piston lower portion)

Piston offset

Direction of piston offset

Clearance between piston and cylinder

Outside diameter of piston pin

Inside diameter of pin hole

70.92-70.97mm(2.77in)

4.0mm(0.156in)

0.5mm(0.0195in)

Inward

0.04-0.006

15.991-16mm(0.624-0.624in)

16.002-16.013mm(0.624-0.625in)

0.15mm

Driving method of balancing block gear driving

Connecting rod of crank

Limit value of runout: C1

C2

Width of crank “A”

Small end free play of connecting rod “F”

Big end free play of connecting rod “D”

Big end radial clearance of connecting rod “E”

55.95-56.00mm(2.18in)

0.8-1.0mm(0.031-.039in)

0.35-0.65mm(0.014-0.025in)

0.01-0.025mm(0.0004-0.001in)

0.03mm

0.06mm

2.0mm

Automatic centrifugal clutch

Clutch shoe: quantity

thickness

Clutch meshing revolution

Clutch stalled revolution

Free length of back spring of brake shoe

Clutch:

Action method of clutch

Clutch piece: quantity

thickness

Friction piece: quantity

thickness

Spring of clutch: quantity

free length

3 pieces

2.0mm(0.078in)

1800-2100r/min

3200-3600r/min

32.47mm(1.27in)

Outside pushing type

4 pieces

1.45-1.75mm(0.057-0.068)

5 pieces

2.94-3.06mm(0.115-0.119in)

4

35.1mm(1.37in)

1.5mm

2.8mm

32.9mm

Shifting mechanism

shifting method

beading limit of fork guide

shift gear cam drunk and fork

0.8mm

Transmission device

offset limit of spindle

offset limit of transmission output shaft

0.08mm

19

Section 5 Requirements for torque fastening

Locking component and location on ATV Hard-

ware

Size of

thread

Qty Nm ft·lb

Cylinder head Bolt M10x238 2 45 33

Cylinder head Bolt M10x216 2 45 33

Front and rear valve cover Bolt M6x20 5 10 7

Cam timing gear cover Bolt M6x25 2 10 7

Oil shield plate comp Bolt M6x12 2 10 7

Cylinder head hexangle Bolt M8x50 2 23 17

Cam stop plate Bolt M6x12 2 10 7

Exhaust stud Bolt M8x45 2 23 17

Intake manifold Bolt M8x25 2 23 17

Timing gear Bolt M10x25 1 45 33

Tensioner plate bolt Bolt M6x16 2 10 7

Tensioner Bolt M6x25 2 10 7

Tensioner plug Bolt M10x12 1 45 33

Cylinder bolt Bolt M6x30 1 10 7

Balanced initiative gear Bolt M10x40 1 45 33

Balanced shaft gear Nut M16 1 197 146

Clutch protection cover bracket Bolt M6x30 4 10 7

Protection cover inner bearing Bolt M6x12 1 10 7

Drain plug Bolt M12x40 1 80 59

Crankcase Bolt M6x50 12 10 7

Crankcase Bolt M8x45 3 23 17

Crankcase Bolt M6x70 3 10 7

Bearing press plate Bolt M6x12 2 10 7

Forward and reverse gear switch Nut M10 2 45 33

Press plate sank Screw M6x16 1 10 7

Rotate speed transducer Bolt M6x12 2 10 7

Torque value of fasteners

Page is loading ...

Baja WD400U User manual

Baja WD400U User manual

Related papers

Other documents