Panasonic VLSWD501UEX, VLSWD501EX Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Panasonic VLSWD501UEX Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Installation Guide
Note to the installer
■ Beforeattemptingtoconnectoroperatethisproduct,pleasereadthelabelontherearof
themainmonitor.
■
Pleasereadthis
guide
carefully,andinstalltheproductsafelyandcorrectlybyfollowing
theinstructions.Carefullyreadtheinformationfoundinthesectiontitled"Foryoursafety"
inparticular.
■
Onlyuseattachments/accessoriesspecifiedbythemanufacturer.
■
Theinstallationshallbecarriedoutinaccordancewithallapplicableinstallationrules.
■
Panasonicassumesnoresponsibilityforinjuriesorpropertydamageresultingfromfailures
arisingoutofimproperinstallationoroperationinconsistentwiththisguide.Additionally,
anyresultingmalfunctionwillnotbecoveredunderthewarranty.
■ Afterinstallation,makesuretoleavethisguidewiththecustomer.
For the Installation of door station
and main monitor station
•VL-V554EXisasurfacemounttype,VL-V554UEX
isaushmounttype.
For your safety
Topreventsevereinjuryandlossoflife/property,readthissectioncarefullybeforeusingthe
producttoensureproperandsafeoperationofyourproduct.
WARNING
Preventingre,electricshockandshortcircuits
Leaveinstallationworktothedealer.
Installationworkrequirestechniqueandexperiences.Failuretoobservethismay
causere,electricshock,injury,ordamagetotheproduct.Consultthedealer.
Electricalconnectionworkshouldbeperformedbycertiedpersonnelonly.Certication
isrequiredforperformingelectricalconnectionwork.Consultyourdealer.
Useonlythespeciedpowersupplyunit.
Donotattempttodisassembleormodifythisproduct.Contactan authorisedservice
centreforrepairs.
Neverinstallwiringduringalightningstorm.
Donotconnectnon-specieddevices.
Donotconnectapowercabletoaterminalthatisnotspeciedinthisguide.
Whenopening holes in walls forinstallationorwiring, or when securingthepower
cable,makesureyoudonotdamageexistingwiringandductwork.
Donotmakeanywiringconnectionswhenthepowersupplyisturnedon.
Donotusethesuppliedpowersupplyunitforoutdoorinstallations(itisforindooruse
only).
Donotinstallthemainmonitorandpowersupplyunitinthefollowingplaces:
- Placeswherethemainmonitorandpowersupplyunitmaybesplashedwithwateror
chemicals.
- Placeswherethereisahighconcentrationofdust,orhighhumidity.
Donotperformanyactions(suchasfabricating,twisting,stretching,bundling,forcibly
bending,damaging,altering,exposingtoheatsources,orplacingheavyobjectsonthe
powercable) thatmaydamage thepowercable. Usingtheproduct withadamaged
powercable may causeelectricshock, shortcircuits,orfire. Contactanauthorised
servicecentreforrepairs.
When existing chime wires are used, it is possible that they containAC voltage.
Contactanauthorisedservicecentre.
Donot installoruse theproductinhealth carefacilitiesif anyregulationspostedin
theareainstructyounottodoso.Hospitalsor healthcare facilitiesmay be using
equipmentthatcouldbesensitivetoexternalRF(radiofrequency)energy.
Do not install or use this product near automatically controlled devices such as
automaticdoors andfirealarms.Radio wavesemittedfrom this productmaycause
suchdevicestomalfunction,resultinginanaccident.
Preventingaccidentsandinjuries
CAUTION
Ifthewiringisunderground,donotmakeanyconnectionsunderground.
Ifthewiringisunderground,useaprotectiontube.
Ifthewiringisoutdoors,useaprotectiontubeorasurgeprotector.
Installtheproductsecurelyadheringto theinstructionsin thisguidetoprevent itfrom
fallingoffthewall.Avoidinstallingontolow-strengthwalls,suchasgypsumboard,ALC
(autoclavedlightweightconcrete),concreteblock,orveneer(lessthan18mmthick)walls.
Preventingelectricshock
Preventinginjury
1-62,4-chome,Minoshima,Hakata-ku,Fukuoka812-8531,Japan
©PanasonicSystemNetworksCo.,Ltd.2013
PNQW3982ZA PC1113MT1113
VL-V554EX/
VL-V554UEX
VL-MWD501EX
Doorstation Mainmonitorstation
Doorstationisdescribedas"doorphone"
andMainmonitorstationisdescribedas
"mainmonitor"inthisguide.
ModelNo.
VL-SWD501EX
VL-SWD501UEX
Wireless Video Intercom System
Toavoidmalfunctionorcommunicationdisturbances,donotinstallthedoorphoneorthemain
monitorinthefollowinglocations:
- Placeswherevibrationoranyotherkindofimpactoccurs.
- Placeswhereechoingisfrequent.
- Placesnearahighconcentrationofdust,hydrogensulphide,ammonia,sulphur,ornoxious
fumes.
■
For the doorphone
Ifastronglightisshiningonthedoorphone,thevisitor’sfacemaynotbedistinguishable.Do
notplacethedoorphoneinthefollowinglocations:
- Wheremostofthebackgroundisthesky.
- Wherethebackgroundisawhitewall,anddirectsunlightwillreectoffit.
- Wheredirectsunlightwillshineonthedoorphone.
Do not place the doorphone in locations where echoing occurs, as this will cause the
doorphonetobeepfrequently.
Dustprotection/waterprotectionisIP54.
Onlywheninstallationworkspeciedinthisguideisproperlyperformedandappropriatewater
protectiontreatmentisperformed.
Makesuretherearofthedoorphoneisnotsubjecttowater.
Dependingontheinstallationlocation,condensationmayformonthedoorphone’slenscover.
Thismaycauseimagestobecomeobscured.Condensationwilldissipateasthetemperature
rises.
■
For the main monitor
Installthe main monitor away fromelectronic appliances such as TVs, radios, personal
computers,air conditioners,boilercontrolpanels withintercom,home securityequipment,
wirelessdevices,ordigitalcordlessphones.
Donotinstallthemainmonitorinplaceswhereitwillbeaffectedbyextremelyhigh-frequency
radiowaves (nearbroadcastingantennasetc.).Thismaycausethe displaytoickeroran
interruptingnoisetooccur.
Leaveat least 20 cm of space above, below,and to the left and right sides ofthe main
monitor.Donotinstallonawallthatisdeeplyrecessed.
Donotinstallthemainmonitorinsideawall.
Besuretoinstallthemainmonitormorethan5mawayfromthedoorphone.
The product operates in the frequency range of 1.88 GHz to 1.90 GHz, and the RF
transmissionpoweris 250 mW (max.).Refertothe "For best performance" sectioninthe
OperatingInstructions.
Inareassurroundedbya highelectrical eld,disturbances mayoccurinthemainmonitor’s
imageorsound.
Supplied accessories for installation
For the doorphone
(EXonly)
Mounting
base×1
(UEXonly)
Flush
mounting
box
×
1
Screw×4(Usedwhen
installingthedoorphone)
(EX

:4mmx12mm)
(UEX:4mmx25mm)
Nameplate×2
(incl.1spare)
Hexwrench×1
For the main monitor
Mounting
bracket×1
Cablebinder×1
Power supply unit and related items
Powersupply
unit×1
(PartNo.VL-PS240)
Cablebinder×2
Important:
You will need the following additional items to install and congure the doorphone
and the main monitor.
[Locally procured]
- Screws(formountingbase:×2,formountingbracket:×2):
Preparethescrews(
thedrawingontheright)accordingto
thematerial,structure,strengthandotherfactorsofthemounting
areaandthetotalweightofobjectstobemounted.
- Powercables(AC/DCcables),wires(fordoorphoneandotherconnections):
Preparecablesandwiresoftheappropriatespecication.(
"Wiretypeandlength")
Note:
Theillustrationsinthesuppliedmanual(s)mayvaryslightlyfromtheactualproduct.
4mm
Precautions for installation
Wiring schematic diagram
Setupcorrectlyaccordingtothefollowingwiringschematicdiagramand"Wiretypeandlength".
Forinformation,suchasordernumbers,aboutoptionaldevicesthatcanbeconnectedto,refertothe"Additional/replacementaccessories"sectionintheOperatingInstructions.
MAIN MONITOR
DOORPHONE 1
DOORPHONE 2
POWER SUPPLY UNIT
220-240VAC
Connectiondeviceforoptionoutput(Acontact)
*1MakesuretoonlyconnectelectricvehiclegatelockstotheS3/S4terminalsofthe
doorphones.
*2MakesuretoonlyconnectelectricdoorlockstotheS1/S2terminalsofthedoorphones.
NP: Non-polarised
Power
supply
Power
supply
Power
supply
Power
supply
12VAC/DC
12VAC/DC
12VAC/DC
12VAC/DC
Electriclock
(Electricvehicle
gatelock)
*1
Electriclock
(Electricdoor
lock)
*2
Electriclock
(Electricdoor
lock)
*2
Electriclock
(Electricvehicle
gatelock)
*1
24VDC
Wire type and length
Wiringrun
Wiretype
*1
Diameter Length(Max.)
Mainmonitor–
Doorphone
A
φ0.65mm 22AWG 100m
φ1.0mm 18AWG 130m
φ0.5mm CAT5 50m
Mainmonitor–
Powersupplyunit
B
φ0.65mm 22AWG 10m
φ1.0mm 18AWG 20m
Powersupplyunit–
ACpowersource
C
φ1.2mm-φ2.0mm
(17AWG-12AWG)
Norequirement
Doorphone–
Electriclock
*2
D
φ0.5mm-φ1.2mm
(24AWG-17AWG)
Accordingtospeci-
cationofconnected
device.
Mainmonitor–
Connectiondeviceforoption
output(Acontact)
*2
E
φ0.5mm-φ1.2mm
(24AWG-17AWG)
Accordingtospeci-
cationofconnected
device.
*1Type:Single-paircablewithoutersheath(jacket)
Conductor:Coppersolid
Acertiedpowersupplywiringhastobeusedwiththisequipment.Therelevantnational
installationand/orequipmentregulationsshallbeconsidered.Acertiedpowersupplywiring
notlighterthanordinarypolyvinylchlorideexiblewiringaccordingtoIEC60227shallbeused.
*2Whenusinganelectriclockoraconnectiondeviceforoptionoutput(Acontact),selectadevice
thatmeetsthefollowingguidelines:
Electriclockconnectionterminal(S1/S2,S3/S4):
- N/Odryclosurecontact
- 12VAC/DC,lessthan1A
Connectiondeviceforoptionoutput(Acontact)terminal(OUT1/OUT2):
- 24VAC/DC,lessthan0.3A(minimumcontact:5VDC1mA)
A D
D
E
B
C
NP
NP
NP
NP
NP
NP
NP
NP
ScrewA
Youcanusethe[Wide/Zoomsettings]settingonthemainmonitortoselecttheareathat
isvisiblewhenavisitorcalls;availablesettingsare[Wide],[Zoom],and[All](entireimage
display).(Defaultsetting:[Wide])
Thefollowingvaluesareforwhenthedoorphoneisinstalledinthestandardposition(thecentre
ofthe doorphone’sheight isapproximately1,450mm)and at a distance ofapproximately
500mmfromthecameralens.
■ Installation height and area visible by the camera lens
When set to zoom
Displaysaportionofthewideimageat2timesthesize.
Because a digital zoom is used, the image quality of zoom
displayislowerthanthatofwidedisplayorentireimagedisplay.
Imagedisplayedon
mainmonitor:
You canusethemainmonitor’s[Zoomposition settings]settingtoselectthedesiredarea
visiblewhenzooming.
Refertothefollowingandcongurethemainmonitor.
Entire image display
Theareaaboveandbelowthewideimageisvisible.
Important:
Onthebottomsurfaceofthedoorphoneandthemountingbase,thereareholestoallowwater
todrain.Donotcoverthemupwheninstalling.
Whenexistingwiring(suchaschimewires)isused:
- ItmaycontainACvoltagethatmaycauseelectricshockand/ordamagetheproduct.
- Neverusethefollowingtypesofwiring.Consultaqualiedtechnician/dealer.
VL-V554EX VL-V554UEX
1
Attachthemountingbasetothewallsecurely.
Mountingbase
(accessory)
Wire(locallyprocured)
Wall
83.5mm
Screws(locallyprocured)×2
Installthemountingbaseonaverticalatwall.
1
Installtheflushmountingboxinthe
wall.
Flushmountingbox(accessory)
100mm
Knockouthole
*1
151mm
37mm
*1Onlyopentheknockoutholesas
requiredforthewiring.
2
Useahexwrench(accessory)toloosenscrewAandremovethefrontpanelofthedoor-
phone.
ScrewA
Frontpanel
2mmhexwrench
(accessory)
3
Connectthewires.
Terminalforthe
mainmonitor
<Rear
view>
Terminalsfortheelectriclocks
Recommendedtorque:
0.5N·m{5.1k
g
f·cm}
Maximumtorque:
0.7N·m{7.1k
g
f·cm}
3-1Loosenthescrews.
3-2Pushinthewirestotheterminalconnectors(non-polar),thentightenthescrews.
4
Attachthedoorphonetothemounting
base.
Screws(accessory)×4
4
Attachthedoorphonetotheflushmounting
box.
Screws(accessory)×4
5
AttachthenameplatetothedoorphoneandusescrewAtosecurethefrontpanel.
Writethenameonthenameplateasneeded.
Nameplate
(accessory)
ScrewA
Recommendedtorque:
0.35N·m{3.6k
g
f·cm}
Approx.500
Approx.170°
Approx.2,250
Imagerange
Approx.115°
Approx.500
Imagedisplayedon
mainmonitor:
Approx.1,600
Approx.650
Approx.1,450
Upanddown
Leftandright(whenlookingfromabove)
Up
Imagerange
Approx.2,050
Approx.500
Centreof
doorphone
Approx.45°
Centre (default)
Approx.45°
Approx.500
Imagerange
Approx.1,650
Down
Approx.45°
Approx.500
Approx.1,400
Imagerange
Left
Approx.1,500
Approx.1,450
Approx.550
Approx.1,450
Approx.1,250
Approx.400
Installing the doorphone
■
About the installation location
Thedevicemustbeinstalledinsideanelectricalpanelorcabinet.
Areadilyaccessibledisconnectdeviceshallbeincorporatedexternaltotheequipment.
- Externaldisconnectdevicemustbecertiedandhaveacreepageandclearancedistance
of3mmormore.
■
Precautions for wiring
Makesureyouturnoffthepoweratthebreakerbeforeperforminganywiringwork.
Always connectAC or DC cables to the appropriate connection terminals. Incorrectly
connectingtheACorDCcablesmaydamagethepowersupplyunit.
Topreventthepower cablesfromdisconnectingandto preventelectric shock,secure the
powercablesusingthecablebinders(accessory)andattachthecablecovers.
How to connect the power cable (AC/DC)
1
StriptheAC/DCcablesasfollows:
7mm
45mm
<ACcable>
<DCcable>
25mm
7mm
2
Removethescrews(
B
)andthenremove
thecablecovers(
A
).
3
ConnecttheAC/DCcabletotheACIN
terminal/DCOUTterminalonthetopand
bottomofthepowersupplyunit,andthen
securethewiresbytighteningthescrews.
Recommendedtorque:
- ACterminal:0.4N·m{4.1k
g
f·cm}
- DCterminal:0.45N·m{4.6k
g
f·cm}
<Frontview>
ACcable
*1
DCcable
Screws
*1
Cablebinders(accessory)
4
Usethecablebinders(accessory)to
securetheAC/DCcables(double-coated
area)tothepowersupplyunit.
5
Makesuretoreplacethecablecovers(
A
).
Connectthepowersupplyunit(accessory)andAC/DCcables(locallyprocured).
CAUTION
Insertthecablesfirmlyalltheway
intotheterminals.
Ifthecablesarenotinsertedall
theway,heatmaybegenerated.
*1 Makesurethattherearenobarewires
exposedoutsidetheproduct.
Screws(
B
)
Cablecovers(
A
)
DCOUTterminal
ACcable
binderhole
ACINterminal
<Topview>
<Bottomview>
DCcable
binderhole
Power supply unit (with cable covers
removed)
Attach to the DIN rail
Attachintheorderdescribedbelowsothathook(b)ispositionedatthebottom.
1
Hanghook(a)ontheDINrail(
A
).
2
Pullandholdtheleverdown(
B
).
3
Securehook(b)totheDINrail(
C
).
Hook(a)
A
B
C
Hook(b)
Main monitor installation position
Installing the main monitor
Mainmonitor
installationposition
82.5mm
82.7mm
2
ConnecttheDCcableandwires.
Connectthewires correctly according to "Wiring schematic
diagram".
3
Mountthemainmonitortothemountingbracket.
3-1 Lineupthetabonthebottomofthebracketwiththegrooveonthemainmonitor(
A
).
3-2 Lineupthetabonthetopofthebracketwiththegrooveonthemainmonitor,and
pushthemainmonitordownuntilitissecure(
B
).
Wall
1
Attachthemountingbrackettothewall
securely.
Installthemountingbracketona vertical
atwall.
A
RemovescrewAandthenremovethe
terminalcover.
B
LoosenscrewBandpushinthewiresof
theDCcabletotheterminalconnectors
(non-polar),thentightenthescrews.
Recommendedtorque:
0.8N·m{8.2k
g
f·cm}
C
Usethecablebinder(accessory)to
securetheDCcable(double-coated
area)tothemainmonitor.
D
Makesuretoreplacetheterminalcover.
How to connect the DC cable:
Whilepressingonthebuttonwithapoint-
edobjectsuchasascrewdriver,insert
thewireintotheterminalconnector.(To
disconnectawire,whilepressingonthe
button,pulloutthewire.)
Barewireattip
9mm
Terminal
Button
Wiringfrom
doorphone
Important:
Donotconnectthepowercable.
(Damagemayoccur.)
How to make wiring connections:
Resetbutton
SDcard
slot
20cm
20cm
20cm
20cm
Cablebinder
(accessory)
12mm
Barewireattip
ScrewB
Forthefollowingreasons,leaveatleast20cmofspace
above,below,andtotheleftandrightsidesofthemain
monitor:
-Topreventmalfunctionandsoundcuttingout
-To ensureSDcardscanbeinsertedandremoved,
andtomakesuretheresetbuttoncanbeused
(theSDcardslotisonthesideofthemainmonitor;
theresetbuttonisonthebottom)
■
About the installation position of the main monitor and mounting bracket
Placethemainmonitorinalocationthatyoureyesarethesameheightasthecentre
ofthedisplay.
Afterdecidingwheretoinstallthemainmonitor,attach
the mounting bracket in thelocationshown on the
right.
Doorphone installation position
Installing the power supply unit
Imagerange:
Approx.900
Approx.500
Approx.85°
Approx.170°
Centre (default)
Imagerange:
Approx.900
Approx.85°
Right
Imagerange:
Approx.900
Approx.500
Approx.170°
Approx.85°
Approx.500
Approx.850
Approx.1,450
Approx.550
32mm
When set to wide (default)
Centreof
doorphone
Centreof
doorphone
Centreof
doorphone
Approx.95°
Centreof
doorphone
Approx.1,450
Approx.500
Approx.900
Approx.170°
Approx.500
Approx.1,100
Approx.2,000
Imagerange
Imagedisplayedon
mainmonitor:
Viewwhenlooking
fromabove
Viewwhenlooking
fromabove
(Units:mm)
Notes about electrical wiring
Makesurenottopinchthewires(asshowntothe
right)onthemountingbracketwheninstalling.
Donotforciblyattachtothemountingbracket.
Vertical,flatwall
Screws
(locallyprocured)
Holeinwall
83.5
60
7
50
Mountingbracket
(Units:mm)
(Units:mm)
(Units:mm)
(Units:mm)
/