Directed Xpresskit DBALL2 Installation guide

Directed
Brand
Directed
Model
Xpresskit DBALL2
Category
Motorcycle Accessories
Type
Installation guide

Directed Xpresskit DBALL2

The DBALL2 is a door lock and transponder interface for many of the latest models of Mitsubishi vehicles. It features tach output and FOB control, making it a versatile and convenient addition to your vehicle's security system. With its ability to integrate with Mitsubishi's factory systems, the DBALL2 provides seamless operation and enhanced functionality. Whether you're looking to upgrade your vehicle's security or simply want to add remote start capabilities, the DBALL2 is an excellent choice.

Directed Xpresskit DBALL2

The DBALL2 is a door lock and transponder interface for many of the latest models of Mitsubishi vehicles. It features tach output and FOB control, making it a versatile and convenient addition to your vehicle's security system. With its ability to integrate with Mitsubishi's factory systems, the DBALL2 provides seamless operation and enhanced functionality. Whether you're looking to upgrade your vehicle's security or simply want to add remote start capabilities, the DBALL2 is an excellent choice.

Index
® Mitsubishi is a registered trademark and property of its respective company.
Vehicle Application Guide................................................................................................................................................
Installation
Type 1..............................................................................................................................................................................
Wiring Reference Chart - Type 1.....................................................................................................................................
Locating Components in the Vehicle -Type 1..................................................................................................................
Type 2..............................................................................................................................................................................
Wiring Reference Chart - Type 2.....................................................................................................................................
Locating Components in the Vehicle -Type 2..................................................................................................................
Type 3..............................................................................................................................................................................
Wiring Reference Chart - Type 3.....................................................................................................................................
Locating Components in the Vehicle -Type 3..................................................................................................................
Type 4..............................................................................................................................................................................
Wiring Reference Chart - Type 4.....................................................................................................................................
Locating Components in the Vehicle -Type 4..................................................................................................................
Programming
Module Programming......................................................................................................................................................
Module Reset & Hard Reset............................................................................................................................................
Feature and Option List...................................................................................................................................................
Feature Programming......................................................................................................................................................
LED Diagnostics and Troubleshooting............................................................................................................................
Limited One Year Consumer Warranty............................................................................................................................
Quick Reference Guide...................................................................................................................................................
02
03
04
05
06
07
08
09
10
11
12
13
14
16
17
18
18
19
20
21
Door lock and transponder interface for many of the latest models of Mitsubishi vehicles. Features
include tach output, and FOB control.
Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Vehicle Application Guide
Page 2
Vehicles
2015
2014
2012
2011
2010
2009
2008
2007
2006
PK-Immobilizer Bypass-Data No Key Req'd
RS-RAP Shut Down (Retained ACC Power)
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Driver Door Pin
SS-Entry Monitoring Trunk/Hatch Pin
ST-Brake Status (foot brake)
ST-E-Brake Status
ST-Ignition Status
Mitsubishi
Eclipse 3* or 4 3* or 4 3* or 4 3* or 4 3 3 3 • • • • D • • • •
Eclipse (Without OEM Alarm) 2 2 2 2 2 2 2 • • • • D • • •
Eclipse Spyder 3* or 4 3* or 4 3* or 4 3* or 4 3 3 3 • • • • D • • • •
Eclipse Spyder (Without OEM Alarm) 2 2 2 2 2 2 2 • • • • D • • •
Endeavor 3* or 4 3* or 4 3* or 4 3* or 4 3* 3* • • • • D • • •
Endeavor (Without OEM Alarm) 2 2 2 2 2 2 • • • • D • • •
Galant 3* or 4 3* or 4 3* or 4 3* or 4 3* or 4 3 3 • • • • D • • •
Galant (Without OEM Alarm) 2 2 2 2 2 2 2 • • • • D • • •
Mirage 1 1 • • • • • • • • •
Legend:
PK: Transponder & Immobilizer Override
DL: OE Door Lock & Alarm Controls
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
* Install Type 3 and 4: the Lock and Unlock wires must be pinned into the connector.
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Page 3
Installation Type 1
31 2
4 5 6
Remote
Starter
10: Blue/White: (-) GWR (Status) Input
Ignition Connector White
(Left side of steering column)
C-22 White 22-pin connector
(Attached to the side
of the fuse box)
(+) Parking Lights
(+) 12V
(-) Ground(-) Ground
(-) GWR (Status)
(+) Ignition Output
(-) Lock: Green, pin 22
(-) Unlock: Lt. Blue, pin 11
(-) Lock Output
(-) Unlock Output
(-) Trunk Status Input
(-) Door Status Input
(+) Brake Status Input
(-) Hood Status Input
(-) E-Brake Status Input
[1] (AC) Tach Input
C-405 White Connector
(Junction Block at driver kick panel)
21
Clutch Pedal
Manual Transmission ONLY
Hood
Without Anti-Theft Security Alarm Only
Hood wire must be connected to vehicle.
(+) Accessory
OR - (+) Starter
Automatic Transmission ONLY
TX
(-) Ground
RX
(+)12V
10
RF
Prog. Button
LED
4
14 12
2
DBALL2
P#: XKD2D65
(+) Ignition: Green, pin 2
(+) Starter: Pink, pin 5
(+) Accessory:
Yellow, pin 4
(+) 12V:
White, pin 1
(+) Clutch: Green, pin 1
HS CAN Low: Black, pin 14
HS CAN High: Brown, pin 6
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
All adapters are displayed from the wire side (unless specified otherwise).
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Status Output: Gray: 6
(-) Hood Status Output: Blue/Red: 12
(-) Door Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
(-) Trunk Status Output: Red/Black: 4
CAN High: Tan/Black: 3
CAN Low: Tan: 4
(+) 12V
(+) 12V: Red: 13
(-) Ground
(-) Ground: Black: 14
1 8
169
22 21 1719 1520 1618 14 13 12
11
10 68 49 57 3 2 1
Diagnostic connector OBDII
(Connector side view)
2 3 4 5
11 12 138 96 7 10
1
(+) Parking Lights:
Green, pin 1
Refer to pages 4-5 for more information on vehicle-specific connections.
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Locating Components in the Vehicle (Type 1)
Page 4
C-22 - White Door Locks Connector
(at Driver Kick Panel, besides fuse box)
(-) Lock: Green, pin22
(-) Unlock: Lt. Blue, pin 11
Unlock:
Lt.Blue, pin 11
Lock:
Green,
pin 22
OBDII Diagnostic Connector - 16-pin Black
CAN Low: Black, pin 14
CAN High: Brown, pin 6
CAN Low:
Black
CAN High:
Brown
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Mirage 2014-2015
Accessory 1 Yellow 4 (+) Ignition Switch 6 White Left side of Steering column
Ignition Green 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V White 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Pink 5 (+) Ignition Switch 6 White Left side of Steering column
Clutch Green 1 (+) Clutch Switch 2 Gray at Clutch pedal
Parking Lights Green 1 (+) C-405 13 White Junction Block
CAN2 High Brown 6 Data OBDII connector 16 Black Drivers under dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers under dash
Lock Green 22 (-) C-22 22 White Right of Junction Block
Unlock Lt. Blue 11 (-) C-22 22 White Right of Junction Block
Ground
Vehicle chassis
TYPE 1
Wiring Reference Chart -Type 1
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Locating Components in the Vehicle (Type 1)
Page 5
Ignition Switch Connector - 6-pin White
(left side of steering column)
(+) 12V: White, pin 1
(+) Ignition: Green, pin 2
(+) Accessory: Yellow, pin 4
(+) Starter: Pink, pin 5
Accessory:
Yellow, pin 4
12V:
White, pin 1
Ignition:
Green, pin 2
Starter:
Pink, pin 5
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Page 6
31 2
4 5 6
Remote
Starter
10: Blue/White: (-) GWR (Status) Input
Ignition Connector Blue
(left side of steering column)
(-) Driver Door Trigger:
Lt. Green, pin 6
(+) 12V
(-) Ground
(+) Accessory 1
(+) Accessory 2
(+) 12V
(+) Parking Lights
(-) Ground
(-) Ground
(-) Hood
(-) Hood
(-) Lock Output
(-) Unlock Output
(-) Trunk Status Input
(+) Brake Status Input
(-) E-Brake Status Input
[1] (AC) Tach Input
(+) Ignition
Diagnostic connector OBDII
(Connector side view)
1 8
169
7
6
5
13
14
15
12
4
3
2 1
8
9
10
11
Junction Block
Front View
C-204 - White Connector
(Front of Junction Block
at Driver Kick Panel)
(-) GWR (Status)
15
14
6
5
4
13
3
12
21
21
1110
2019
16
7
22
17
8
23
18
9
24
Junction Block
Rear View
(driver kick panel)
C-219 White 24-pin Connector
(Rear of Junction Block
at Driver Kick Panel)
(-) Door Status Input
TX
(-) Ground
RX
(+)12V
10
RF
Prog. Button
LED
4
14 12
2
DBALL2
P#: XKD2D65
HS CAN High: Red, pin 6
(-) Unlock:
Lt. Green/Red, pin 14
(-) Lock: Violet/White
or Violet, pin 13
HS CAN Low: Black, pin 14
(+) Ignition:
Red or Black/White,
pin 2
(+) Starter: Black/Yellow, pin 5
(+) Accessory 1:
Blue/Red, pin 4
(+) 12V:
Blue/Yellow,
pin 1
(+) Accessory 2: Blue/Black, pin 6
Not required in D2D mode.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
(+) 12V: Red: 13
(-) Ground: Black: 14
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Status Output: Gray: 6
(-) Door Status Output: Green/White: 3
(-) E-Brake Status Output Black/White: 1:
Manual Transmission Eclipse ONLY
(-) Trunk Status Output: Red/Black: 4
(-) Auto Headlamp Shutoff Output: Green/Black: 2
Manual Transmission ONLY
(+) Starter
1 2 3 4
8 9 1011
5
12
13
6
14
7
15
C-208 White connector
(Junction Block at Driver Kick Panel)
(+) Parking Lights:
Green/White, pin 2
(-) Starter
21
Clutch Pedal
(+) Clutch:
Brown/Black,
pin 2
30
86 85
87
87a
(+) 12V
Relay
pin 87a
Relay
pin 30
CUT
(-) Trunk Release
3: Red/White: (-) Trunk Release
Refer to pages 7-8 for more information on vehicle-specific connections.
Installation Type 2
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Wiring Reference Chart -Type 2
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Eclipse (without OEM alarm) 2006-12
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Red 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Clutch Brown/Black 1 Open Clutch Switch 2 White at Clutch pedal
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock Violet/White 13 (-) C-219 24 White Junction Block
Unlock Lt. Green/Red 14 (-) C-219 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Eclipse Spyder (without OEM alarm) 2006-12
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Red 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Clutch Brown/Black 1 Open Clutch Switch 2 White at Clutch pedal
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock Violet/White 13 (-) C-219 24 White Junction Block
Unlock Lt. Green/Red 14 (-) C-219 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground Vehicle chassis
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Endeavor (without OEM alarm) 2006-11
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Red 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Clutch Brown/Black 1 Open Clutch Switch 2 White at Clutch pedal
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock Violet/White 13 (-) C-219 24 White Junction Block
Unlock Lt. Green/Red 14 (-) C-219 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Galant (without OEM alarm) 2006-12
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Black/White 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock Violet 13 (-) C-217 24 White Junction Block
Unlock Lt. Green/Red 14 (-) C-217 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground
TYPE 2
Vehicle chassis
TYPE 2
Vehicle chassis
TYPE 2
Vehicle chassis
TYPE 2
Page 7
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Locating Components in the Vehicle (Type 2)
Ignition Connector - 6-pin Blue
(left side of steering column)
(+) 12V: (pin 1) Blue/Yellow
(+) Ignition: (pin 2) Red or Black/White
(+) Accessory 1: (pin 4) Blue/Red
(+) Starter: (pin 5) Black/Yellow
(+) Accessory 2: (pin 6) Blue/Black
Junction Block
C-204 - White connector
(above the fuse box)
(-) Door Status Output: (pin 6) Light Green
Page 8
Ignition
Connector
Ignition
Black/White
Accessory
Blue/Red
12V
Blue/Yellow
Starter
Black/Yellow
Junction
Block
Rear Left Door Pin
Orange/Black, pin 10 (-)
Driver’s Door Pin
Lt. Green, pin 6 (-)
Driver’s Door Trigger
Lt.Green, pin 6 (-)
Rear Left Door Trigger
Orange/Black, pin 10 (-)
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Junction
Block
Rear View
(driver kick
panel)
Page 9
Installation Type 3
Remote
Starter
10: Blue/White: (-) GWR (Status) Input
(-) Ground(-) Ground
(-) Hood(-) Hood
(-) Lock Output
(-) Unlock Output
(-) Trunk Status Input
(+) Brake Status Input
(-) E-Brake Status Input
[1] (AC) Tach Input
Diagnostic connector OBDII
(Connector side view)
1 8
169
7
6
5
13
14
15
12
4
3
2 1
8
9
10
11
Junction Block
Front View
C-204 -White Connector
(Front of Junction Block
at Driver Kick Panel)
(-) GWR (Status)
15
14
6
54
13
3
12
21
2
1
11
10
20
19
16
7
22
17
8
23
18
9
24
C-217 White 24-pin
Connector
(-) Door Status Input
TX
(-) Ground
RX
(+)12V
10
RF
Prog. Button
LED
4
14 12
2
DBALL2
P#: XKD2D65
(-) Driver Door Trigger:
Lt. Green, pin 6
HS CAN High: Red, pin 6
HS CAN Low: Black, pin 14
(-) Lock/Arm:
Lt. Green/Black,
pin 22
(-) Unlock/Disarm:
Red/Green, pin 5
Not required in D2D mode.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
(+) 12V (+) 12V: Red: 13
(-) Ground (-) Ground: Black: 14
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Status Output: Gray: 6
(-) Door Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Manual Transmission Eclipse ONLY
(-) Trunk Status Output: Red/Black: 4
(-) Auto Headlamp Shutoff Output: Green/Black: 2
Solder onto a diode, cut away the unneeded
portion, and then insert into empty pin as shown.
Empty pin
Diode
Solder the wire to secure it on the metal pin.
This part can be removed because
only the metal pin is needed to
secure the contact in the empty pin.
Unlock* wire from Remote Starter
*Lock: Same procedure have to be done for missing Lock wire.
If there’s no Lock/Unlock wire present in the connector:
31 2
4 5 6
Ignition Connector Blue
(left side of steering column)
(+) Accessory 1
(+) Accessory 2
(+) 12V
(+) Parking Lights
(+) Ignition
(+) Ignition:
Red or Black/White,
pin 2
(+) Starter: Black/Yellow, pin 5
(+) Accessory 1:
Blue/Red, pin 4
(+) 12V:
Blue/Yellow,
pin 1
(+) Accessory 2: Blue/Black, pin 6
Manual Transmission ONLY
(+) Starter
1 2 3 4
8 9 1011
5
12
13
6
14
7
15
C-208 White connector
(Junction Block at Driver Kick Panel)
(+) Parking Lights:
Green/White, pin 2
(-) Starter
21
Clutch Pedal
(+) Clutch:
Brown/Black,
pin 2
30
86 85
87
87a
(+) 12V
Relay
pin 87a
Relay
pin 30
CUT
If there's no
Lock/Unlock wires,
you can either insert
lock/unlock wires directly
as shown below or use
Installation Type 4 on
page 12.
(-) Trunk Release
3: Red/White: (-) Trunk Release
Refer to pages 10-11 for more information on vehicle-specific connections.
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Wiring Reference Chart -Type 3
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Eclipse 2006-12
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Red 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Clutch Brown/Black 1 Open Clutch Switch 2 White at Clutch pedal
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock/Arm Lt. Green/Black 22 (-) C-217 24 White Junction Block
Unlock/Disarm Red/Green 5 (-) C-217 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Eclipse Spyder 2006-12
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Red 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Clutch Brown/Black 1 Open Clutch Switch 2 White at Clutch pedal
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock/Arm Lt. Green/Black 22 (-) C-217 24 White Junction Block
Unlock/Disarm Red/Green 5 (-) C-217 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground Vehicle chassis
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Endeavor 2006-11
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Black/White 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock/Arm Lt.Green/Black 22 (-) C-217 24 White Junction Block
Unlock/Disarm Red/Green 5 (-) C-217 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Galant 2006-12
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Black/White 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock/Arm Lt.Green/Black 22 (-) C-217 24 White Junction Block
Unlock/Disarm Red/Green 5 (-) C-217 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground Vehicle chassis
TYPE 3
Vehicle chassis
TYPE 3TYPE 3
Vehicle chassis
TYPE 3
Page 10
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Locating Components in the Vehicle (Type 3)
Ignition Connector - 6-pin Blue
(left side of steering column)
(+) 12V: (pin 1) Blue/Yellow
(+) Ignition: (pin 2) Red or Black/White
(+) Accessory 1: (pin 4) Blue/Red
(+) Starter: (pin 5) Black/Yellow
(+) Accessory 2: (pin 6) Blue/Black
Junction Block
C-204 - White connector
(above the fuse box)
(-) Door Status Output: (pin 6) Light Green
Page 11
Ignition
Connector
Ignition
Black/White
Accessory
Blue/Red
12V
Blue/Yellow
Starter
Black/Yellow
Junction
Block
Rear Left Door Pin
Orange/Black, pin 10 (-)
Driver’s Door Pin
Lt. Green, pin 6 (-)
Driver’s Door
Trigger
Lt.Green, pin 6 (-)
Rear Left Door
Trigger
Orange/Black,
pin 10 (-)
(TYPE 3 only) C-217 - White ECU Connector
(at Junction Block, above fuse box)
(-) Lock (pin 13): Violet or Violet/White
(-) Unlock (pin 14): Light Green/Red
or
*(-)Arm (pin 22): Lt. Green/Black or
needs to be pinned.
*(-)Disarm (pin 5): Red/Green or needs
to be pinned.
*See page 5 about pinning the connector.
ECU
Connector
Unlock From Elec. Switch
Lt. Green/Red, pin 14 (-)
Lock From Elec. Switch
Violet, pin 13 (-)
Rear Right Door Pin
Orange/Black (-)
Unlock & Disarm
From Driver’s Key Switch
Red/Green, pin 5 (-)
Rear Right Door
Lock & Arm
From Driver’s
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
15
14
6
54
13
3
12
21
2
1
11
10
20
19
16
7
22
17
8
23
18
9
24
Page 12
Remote
Starter
10: Blue/White: (-) GWR (Status) Input
(+) 12V
(-) Ground
(-) Trunk Status Input
(+) Brake Status Input
(-) E-Brake Status Input
[1] (AC) Tach Input
Diagnostic
connector OBDII
(Connector side view)
1 8
169
7
6
5
13
14
15
12
4
3
2 1
8
9
10
11
Junction Block
Front View
C-204 - White Connector
(Front of Junction Block
at Driver Kick Panel)
(-) GWR (Status)
(-) Lock Output
(-) Unlock Output
Diodes 1Amp
Keysense:
Blue/Red, pin 6
4
3 5 6 7
1 2
White or Black Connector
(Left side of steering column)
C-217 White Connector
(Rear of junction block,
at Driver Kick Panel)
Junction Block
Rear View
(Driver kick panel)
(-) Door Status Input
Diodes are
ONLY required
in W2W.
TX
(-) Ground
RX
(+)12V
10
RF
Prog. Button
LED
4
14 12
2
DBALL2
P#: XKD2D65
(-) Driver Door Trigger:
Lt. Green, pin 6
HS CAN High: Red, pin 6
HS CAN Low: Black, pin 14
(-) Lock/Arm:
Violet/White or Violet,
pin 13
(-) Unlock/Disarm:
Lt. Green/Red,
pin 14
Not required in D2D mode.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Status Output: Gray: 6
(-) Door Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
Manual Transmission Eclipse ONLY
(-) Trunk Status Output: Red/Black: 4
(+) Ignition Output: Yellow: 8
(+) 12V: Brown: 7
Keysense: Orange/Red: 10
Keysense: Yellow/Red: 11
(+) 12V: Red: 13
(-) Ground: Black: 14
(-) Alarm & Auto Headlamp Shutoff Output: Green/Black: 2
(-) Ground
(-) Ground
(-) Hood
(-) Hood
31 2
4 5 6
Ignition Connector Blue
(left side of steering column)
(+) Accessory 1
(+) Accessory 2
(+) 12V
(+) Parking Lights
(+) Ignition
(+) Ignition:
Red or Black/White,
pin 2
(+) Starter: Black/Yellow, pin 5
(+) Accessory 1:
Blue/Red, pin 4
(+) 12V:
Blue/Yellow,
pin 1
(+) Accessory 2: Blue/Black, pin 6
Manual Transmission ONLY
(+) Starter
1 2 3 4
8 9 1011
5
12
13
6
14
7
15
C-208 White connector
(Junction Block at Driver Kick Panel)
(+) Parking Lights:
Green/White, pin 2
(-) Starter
21
Clutch Pedal
(+) Clutch:
Brown/Black,
pin 2
30
86 85
87
87a
(+) 12V
Relay
pin 87a
Relay
pin 30
CUT
CUT
(-) Trunk Release
3: Red/White: (-) Trunk Release
1: Green: (-) Lock/Arm Input
2: Blue: (-) Unlock/Disarm Input
Refer to pages 13-15 for more information on vehicle-specific connections.
Installation Type 4
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Vehicle wiring reference charts
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Eclipse 2006-12
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Red 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock/Arm
Violet/White or
Violet
13 (-) C-217
24
White Junction Block
Unlock/Disarm Lt.Green/Red 14 (-) C-217 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Eclipse Spyder 2006-12
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Red 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
Keysense Blue/Red 6 Open Key Switch 7 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock
Violet/White or
Violet
13 (-) C-217
24
White Junction Block
Unlock Lt. Green/Red 14 (-) C-217 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground Vehicle chassis
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Endeavor 2006-11
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Black/White 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
Keysense Blue/Red 6 (+) Key Switch 7 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock
Violet/White or
Violet
13 (-) C-217
24
White Junction Block
Unlock Lt. Green/Red 14 (-) C-217 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground Vehicle chassis
Function Wire Color Pin Polarity Connector Nb. Pins Conn. Color Location on vehicle
Galant 2006-12
Accessory 1 Blue/Red 4 (+) Ignition Switch 6 White Left side of Steering column
Accessory 2 Blue/Black 6 (+) Ignition Switch 6 White Left side of Steering column
Ignition Black/White 2 (+) Ignition Switch 6 White Left side of Steering column
Power 12V Blue/Yellow 1 (+) Ignition Switch 6 White Left side of Steering column
Starter Black/Yelllow 5 (+) Ignition Switch 6 White Left side of Steering column
CAN2 High Red 6 Data OBDII connector 16 Black Drivers Under Dash
CAN2 Low Black 14 Data OBDII connector 16 Black Drivers Under Dash
Parking Lights Green/White 2 (+) C-208 15 White Junction Block
Lock Violet 13 (-) C-217 24 White Junction Block
Unlock Lt. Green/Red 14 (-) C-217 24 White Junction Block
Door Trigger Lt. Green 6 (-) C-204 15 White Junction Block
Ground Vehicle chassis
TYPE 4 TYPE 4
Vehicle chassis
TYPE 4TYPE 4
Installation Type 4
Page 13
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Locating Components in the Vehicle (Type 4)
Ignition Connector - 6-pin Blue
(left side of steering column)
(+) 12V: (pin 1) Blue/Yellow
(+) Ignition: (pin 2) Red or Black/White
(+) Accessory 1: (pin 4) Blue/Red
(+) Starter: (pin 5) Black/Yellow
(+) Accessory 2: (pin 6) Blue/Black
Junction Block
C-204 - White connector
(above the fuse box)
(-) Door Status Output: (pin 6) Light Green
Page 14
Ignition
Connector
Ignition
Black/White
Accessory
Blue/Red
12V
Blue/Yellow
Starter
Black/Yellow
Junction
Block
Rear Left Door Pin
Orange/Black, pin 10 (-)
Driver’s Door Pin
Lt. Green, pin 6 (-)
Driver’s Door Trigger
Lt.Green, pin 6 (-)
Rear Left Door Trigger
Orange/Black, pin 10 (-)
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
(TYPE 4 only) Ignition switch
Eclipse & Eclipse Spyder: White connector
Endeavor & Galant: Black connector
(left side of steering column)
Keysense (pin 6): Blue/Red
Page 15
Locating Components in the Vehicle (Type 4)
Ignition
Switch
Key Sensor : Blue/Red (open)
Open this wire with
a relay set for Ground
When Running
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Page 16
Module Programming
4
3
The LED turns ON green for 3 seconds and shuts off.
Remove the key from ignition.
Turn the Ignition ON using the key.
2
Key IN
OFF
START
IGN
Key OUT
OFF
START
IGN
&
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit
available functions and features.
1. Connect the interface module to your computer using the XKLoader.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware
that is currently saved on the interface module will be indicated in the top right corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select Flash Standard install, and follow the instructions provided on the screen.
5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.
6. The following message will be displayed when the upload is completed:
“The flashing is successfully completed. You may now unplug the kit.”
You can now proceed with the programming instructions below.
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to
the module, then connect the 4-pin D2D harness.
D2D Installation
W2W Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the
module, then connect the 14-pin harness to the module.
10-pin
D2D
st
1
12-pin
14-pin
nd
2
rd
3
10-pin
D2D
st
1
th
4
12-pin
14-pin
nd
2
rd
3
1
Solid
OffSolid x3 secs
Wait until the LED turns ON solid red.
You have successfully completed the module programming sequence.
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
2
Solid
&
Solid
Flashes
&
Release
3
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds
until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
Warning Against Executing a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such
as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
1
OR
If required for your installation, connect the 10-pin, 12-pin &
14-pin harnesses to the module. Press and hold the
programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
W2W Installation
10-pin
D2D
st
1
12-pin
14-pin
nd
2
th
4
rd
3
10-pin
D2D
st
1
th
5
12-pin
14-pin
nd
2
rd
3
th
4
Module Reset
Hard Reset
2
& &
Solid Solid
Release
Wait 3 seconds until the LED turns ON solid orange then release the
programming button. The LED then turns ON solid red.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed
to the module using the web config tool will not be affected.
1
OR
If required for your installation, connect the 10-pin, 12-pin &
14-pin harnesses to the module. Press and hold the
programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
W2W Installation
10-pin
D2D
st
1
12-pin
14-pin
nd
2
th
4
rd
3
10-pin
D2D
st
1
th
5
12-pin
14-pin
nd
2
rd
3
th
4
Page 17
Wire jump template
Feature and Option List
Page 18
To enter feature programming routine
-
Turn the ignition ON, then OFF.
-
Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.
-
The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat
until a new command is entered.
Changing feature options
-
Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.
-
The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly
the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature
-
Press and release the programming button a number of times to advance from the current feature to the next desired feature.
-
The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed
-
Other features can be programmed.
-
The feature programming can be exited.
Exiting feature programming
-
No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.
OR
-
Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the
end of the programming sequence.
Feature Programming
Programming
Button
* Default Option
Feat. Operation Flashes/Options Description
1. No RF Output*
Module is connected to a remote starter using a standard installation.
2. RFTD Output
Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Disabled
The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command
will be executed at the beginning or end of the sequence; it must be controlled by the Remote
Starter.
2. Safelock
Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will
unlock at the beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm
the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm
control must often be done by lock or unlock operation. This could create unnecessary actions
on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will
monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle
is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart
OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is
not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with
this option and will make it invisible to the user.
RFTD Output
Type
1
2
Smart OEM
Alarm Control
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
LED Status Description Troubleshooting
OFF Module has no power.
Make sure the D2D harness is connected or that the
12 Volt is present between the red and black wires. If
the 12 Volt is present, the module may be defective.
Solid
red
Waiting to begin the
programming sequence.
Make sure that all the connections are correct (see
wiring diagram)
Solid green
for 3 seconds
Module was successfully
programmed.
Normal operation.
Flashes
red x2
CAN2 not detected.
Check the Tan - Tan/Black wire connections. Wake
up the data bus by turning the ignition on and try
again.
Flashes red,
red, then
orange x10
OBDII feature
not supported.
Diagnostic data bus not detected. Some features are
not supported by SmartStart. This can be caused by
missing wire connections or module hardware
limitation. Refer to the wiring installation section to
check the connections.
Flashes
green
GROUND OUT ON (GWR)
command received.
Otherwise, the Ground While Running (status) signal
was lost or was never received by the module.
Commands can come from RF, D2D or W2W.
Flashes
red & orange
IGNITION ON
command received.
Otherwise, the ignition signal was not received by the
module. In a W2W install, it will show only if the
ignition input wire is used.
Flashes
green quickly
START ON
command received.
Otherwise, the start signal was not received by the
module. In a W2W install, it will show only if the
ignition input wire is used.
External Module Synchronisation
External Module Synchronisation
Module Programming - Error codes
Module Programming
Page 19
LED Diagnostics and Troubleshooting
Solid red
Flashes red
x2
Solid green
x3 sec
Flashes
red & orange
Flashes
green quickly
Flashes
green
Flashes
red, red.
& orange
x10
Off
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed
Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the
security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material
under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer;
and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the
following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete
product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its
intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or
other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING
BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY,
FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL
PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY
PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS
PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF
THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR
INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS,
AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION,
LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING
DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF
CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE
DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED
TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE
RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL
DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL
LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE
MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE
PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of
America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations
on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has
not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.
For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s
website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select
vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no
circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any
consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor
will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data
bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this
product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes
any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876
B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;
7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:
2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European
Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Limited One Year Consumer Warranty
Page 20
Rev.: 20150814
Platform: DBALL2
Firmware: MIT4
© 2015 Directed. All rights reserved.
Wire jump template
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21

Directed Xpresskit DBALL2 Installation guide

Directed
Brand
Directed
Model
Xpresskit DBALL2
Category
Motorcycle Accessories
Type
Installation guide

Directed Xpresskit DBALL2

The DBALL2 is a door lock and transponder interface for many of the latest models of Mitsubishi vehicles. It features tach output and FOB control, making it a versatile and convenient addition to your vehicle's security system. With its ability to integrate with Mitsubishi's factory systems, the DBALL2 provides seamless operation and enhanced functionality. Whether you're looking to upgrade your vehicle's security or simply want to add remote start capabilities, the DBALL2 is an excellent choice.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents