2. Directed
  3. DBALL2-TL7

Directed DBALL2-TL7 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Directed DBALL2-TL7 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Index
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
® Toyota Scion are registered trademarks and property of .and their respective companies
Vehicle Application Guide ....... .................. .................................. ............................... ....................................................
Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)
Type 1........................................ ....................................................................................................................................
Type 2............................................................................................................................................................................
Type 3............................................................................................................................................................................
Type ............................................................................................................................................................................4
Type ........................................ ...........................................................................................................5 .........................
T6ype ...........................................................................................................................................................................
T7ype ...........................................................................................................................................................................
T8ype ...........................................................................................................................................................................
Type 9............................................................................................................................................................................
Programming
Module Programming.............. .......................................................................................................... ............................
Module Reset ard Reset....................................................................................................& H ......................................
Features & Option List. .................................................................................................................... ..............................
Features ....................................................................................................................Programming.. ............................
LED Diagnostics ................................................................................................................... ..& Troubleshooting. .......
Limited One-Year Consumer Warranty..........................................................................................................................
Quick Reference Guide............................................................................................. ....................................................
02
03
06
08
10
12
14
16
18
20
22
23
24
25
26
28
29
Installation Guide
Update Alert: Firmware updates are posted the web on a regular basis. We recommendon
that you check for firmware and/or install guide updates prior to installing this product.
The TL7 firmware for 2 is an all-in-one door lock and override module compatible with specificDBALL
Scion and Toyota vehicles.
This module can only be flashed and configured using Xpress at www.directechs.com orVIP
using the Directechs Mobile application for smartphones. Refer to
the Module Programming
section on page 22
for more information.
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Vehicle Application Guide
Page 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year
allows you to determine which installation type should be used for your vehicle.
Key Type
G-stamped keys Standard Key
For vehicles with key , seedot-stamped s the
1TL firmware.
Some Toyota 2010+ models have
different encryption types. Please
look at your key blade and identify
the markings. A “G” means the
vehicle is compatible with the 7TL
firmware.
H-stamped keys
H
It is important to make sure you do connect the keysense wire in the installation for each of these vehicles orNOT
you will encounter issues when attempting to start the vehicle.
For vehicles with key , seedot-stamped s the
10TL firmware.
Vehicles
2017
2016
2015
2014
2013
2012
2011
2010
PK-Immobilizer Bypass-Data No Key Req'd
AV-Parking Lights Control
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
DL-Sliding Door Control Driver
DL-Sliding Door Control Passenger
DL-Trunk / Hatch Release
FOB-Control of aftermarket alarm with OEM remote
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring Trunk/Hatch Pin
SS-Factory Alarm Trigger Monitoring
ST-Brake Status (foot brake)
ST-Door Locks Status
ST-E-Brake Status
ST-Ignition Status
Scion
iQ 1111
••••••• •• •D•D••
tC 111111
••••••• • ••••D•D••
xB 22222
••••••• D••••D•D••
xD 5555
••••••• D•• •D•D••
Toyota
4Runner (G Key) 11111111
••••••• • ••••D•D••
Camry(GKey) 88811
••••••• •D••••D•D••
Corolla (G Key) 2 2
••••••• •D••••D•D••
Highlander (G Key) 6 6 6
••••••• D••••D•D••
Highlander Hybrid (G Key) 6 6
••••••• D••••D•D••
Matrix(GKey) 222
••••••• D••••D•D••
Priusc 111
••••••• •• •D•D••
RAV4 (G Key) 2 2
••••••• D•• •D•D••
Sequoia (G Key) 3333
••••••• D••••D•D••
Sienna (G Key) 7777
••••••••••D••••D•D••
Tacoma(GKey) 44444
•
Tundra (G Key) 9999999
••••••• D••••D•D••
Venza(GKey) 1111111
••••••• • ••••D•D••
Yaris(GKey) 1115
••••••• •• •D•D••
Legend:
D: Data-to-Data (D2D) only
AV: Horn & Lights Controls
•: D2D & Wire-to-Wire (W2W)
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/FOB Remote
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
* Version 1.27+ : The motorized trunk feature needs to be enabled during the firmware flashing process.
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Not required in D2D mode.
It is important to make sure you do connect the keysense wire in th installation or youNOT is
will encounter issues when attempting to start the vehicle.
18
169
Diagnostic
connector OBDII
Remote
Starter
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
10: (-) GWR (Status) InputBlue/White:
9: (+) Ignition InputPink:
[4] Autolights Interr. (conn. side): 11Yellow/Red:
[3] in 18(-) Parking Lights: P
[4] Autolights Interr. (veh. side): 10Orange/Red:
(+) Brake Output: 6Status Gray:
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
SIL: 10Yellow/Black:
RDA: 11Orange/Black:
[]2
(-) Hood Status Output: 12Blue/Red:
HS CAN : PHigh in 6
SIL in 7: P
RDA
HS CAN : PLow in 14
Headlight
Switch
(+) 12V
(-) Ground
(+) 12V : 13Input Red:
(-) Ground: 14Black:
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output2
(+) Starter Output1
[3]
Output(-) Parking Lights
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[2]
(-) Hood Status Input
(+) Brake InputStatus
(-) Ground
(-) OutputLock
(-) OutputUnlock
(-) Trunk Output
(-) GWR Output
[4] : PAutolights in 19
Make this connection
only if the vehicle is
equipped with Automatic
Headlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
Body ECU Connector
Note: RDA wire is NOT
required in all vehicles.
Refer to vehicle Wiring and
Connector References
Information for wire and
connector details.
Ignition onnectorC
Fuse Box Connector
Refer to the Vehicle Wiring
Reference Information for wire
and connector details.
4321
8765
1
CUT
Installation Type 1
Page 3
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
10
DBALL/
DBALL2
RF
Prog utton. B
LED
4
14
12
2
[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;
refer to the Vehicle Application Guide for compatibility.
[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[]3 Parking light output only required if Parking Lights are not supported in data.
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Type 1 - Vehicle Wiring Reference Chart
Page 4
Function Color Pin Polarity Location Color Pins
Scion iQ 2012-2015
HS CAN High Violet 6 Data OBDII connector. Black 16
HS CAN Low White 14 Data OBDII connector. Black 16
SIL Red 7 Data OBDII connector. Black 16
RDA Brown 26 Data Body ECU. Gray 30
Parking Lights Yellow 18 (-) Headlight Switch. White 20
Autolights Gray 19 Cut Headlight Switch. White 20
Ignition 1 Brown 6 (+) Ignition Switch. White 8
Ignitiion 2 Lt. Blue 4 (+) Ignition Switch. White 8
Starter 1 Red 8 (+) Ignition Switch. White 8
Starter 2 Lt. Green 1 (+) Ignition Switch. White 8
12V Blue 7 (+) Ignition Switch. White 8
Scion tC 2011-2016
HS CAN High Lt.Green 6 Data OBDII Connector. White 16
HS CAN Low White 14 Data OBDII Connector. White 16
SIL Violet 7 Data OBDII Connector. White 16
RDA Lt. Green 26 Data Body ECU. White 30
Parking Lights Violet 18 (-) Headlight Switch. White 20
Autolights
Ignition 1 Gray 6 (+) Ignition Switch. White 8
Ignition 2 Gray 4 (+) Ignition Switch. White 8
Starter 1 Green 8 (+) Ignition Switch. White 8
Starter 2 Tan 1 (+) Ignition Switch. White 8
12V White 7 (+) Ignition Switch. White 8
Toyota 4Runner (G Key) 2010-2017
HS CAN High Violet 6 Data OBDII Connector. White 16
HS CAN Low White 14 Data OBDII Connector White 16
SIL Green 7 Data OBDII Connector White 16
RDA Pink 26 Data Body ECU. White 30
Parking Lights Red 18 (-) Headlight Switch. White 20
Autolights White 19 Cut Headlight Switch. White 20
Ignition 1 Black 6 (+) Ignition Switch. White 8
Ignitiion 2 Violet 4 (+) Ignition Switch. White 8
Starter 1 Red 8 (+) Ignition Switch. White 8
Starter 2 Black 1 (+) Ignition Switch. White 8
12V Green 7 (+) Ignition Switch. White 8
Toyota Camry (G Key) 2010-2011
HS CAN High Black 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
SIL Gray 7 Data OBDII. Black 16
RDA Blue 12 Data Body ECU, driver dash fusebox. White 28
Parking Lights Black 18 (-) Headlight switch. White 20
Autolights Green 19 Cut Headlight switch White 20
12V Black 5 (+) Ignition switch. White 8
Accessory White 2 (+) Ignition switch. White 8
Ignition 1 Yellow 6 (+) Ignition switch. White 8
Ignition 2 Pink 1 (+) Ignition switch. White 8
Starter 1 Blue 7 (+) Ignition switch. White 8
Starter 2 Gray 3 (+) Ignition Switch. White 8
Wire Information
Connector Information
Not equipped.
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Page 5
Not equipped.
Wire Information Connector Information
Not equipped.
Not equipped.
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Not required in D2D mode.
Remote
Starter
Headlight Switch
(+) 12V
(-) Ground
[3]
Output(-) Parking Lights
CUT
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[]2
(-) Hood Status Input
(+) Brake InputStatus
(-) Ground
(+) 12V : 13Input Red:
(-) Ground: 14Black:
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
10: (-) GWR (Status) InputBlue/White:
9: (+) Ignition InputPink:
(-) OutputLock
(-) OutputUnlock
(-) GWR Output
18
169
Diagnostic
onnector OBDIIC
HS CAN : PHigh in 6
SIL in 7: P
HS CAN : PLow in 14
[]1 (AC) Tach Output: 5Violet/White:
(+) Brake Output: 6Status Gray:
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
SIL: 10Yellow/Black:
[]2
(-) Hood Status Output: 12Blue/Red:
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output2
(+) Starter Output1
[4]
Autolights Interr. (conn. side): 11Yellow/Red:
[4]
Autolights Interr. (veh. side): 10Orange/Red:
[4]
Autolights in 19: P
Make this
connection if theonly
vehicle is equipped
with
Automatic Headlamps.
Ignition onnectorC
Fuse Box Connector
Refer to the Vehicle Wiring
Reference Information for wire
and connector details.
4321
8765
1
It is important to make sure you do connect the keysense wire in th installation or youNOT is
will encounter issues when attempting to start the vehicle.
[3] in 18(-) Parking Lights: P
(-) putTrunk In
3 Trunk: (-) InputRed/White:
Installation Type 2
Page 6
10
RF
Prog utton. B
LED
4
14
12
2
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
DBALL2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;
refer to the Vehicle Application Guide for compatibility.
[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Function Color Pin Polarity Location Color Pins
Scion xB 2011-2015
HS CAN High Lt. Green 6 Data OBDII Connector. Black 16
HS CAN Low White 14 Data OBDII Connector. Black 16
SIL White 7 Data OBDII Connector. Black 16
RDA
Parking Lights White 18 (-) Headlight Switch. White 20
Autolights
Ignition 1 Gray 6 (+) Ignition Switch. White 8
Ignition 2 White 4 (+) Ignition Switch. White 8
Starter 1 White 8 (+) Ignition Switch. White 8
Starter 2 White 1 (+) Ignition Switch. White 8
12V White 7 (+) Ignition Switch. White 8
Toyota Corolla (G Key) 2012-2013
HS CAN High Lt. Green 6 Data OBDII Connector. Black 16
HS CAN Low White 14 Data OBDII Connector. Black 16
SIL White 7 Data OBDII Connector. Black 16
RDA
Parking Lights Brown or White 18 (-) Headlight Switch. White 20
Autolights
Ignition 1 Brown or Gray 6 (+) Ignition Switch. White 8
Ignition 2 Green or White 4 (+) Ignition Switch. White 8
Starter 1 Black or White 8 (+) Ignition Switch. White 8
Starter 2 White (if equipped) 1 (+) Ignition Switch. White 8
12V White 1 (+) Dash Fusebox. White 1
Toyota Matrix (G Key) 2012-2014
HS CAN High Lt. Green 6 Data OBDII Connector. White 16
HS CAN Low White 14 Data OBDII Connector. White 16
SIL White 7 Data OBDII Connector. White 16
RDA
Parking Lights Brown 18 (-) Headlight Switch. White 20
Autolights Gray 19 Cut Headlight Switch. White 20
Ignition 1 Brown 6 (+) Ignition Switch. White 8
Ignition 2 Green 4 (+) Ignition Switch. White 8
Starter 1 Black 8 (+) Ignition Switch. White 8
Starter 2 White (2.4L only) 1 (+) Ignition Switch. White 8
12V Black 1 (+) Dash Fusebox. White 1
Toyota RAV4 (G key) 2011-2012
HS CAN High Black 6 Data OBDII Connector. White 16
HS CAN Low White 14 Data OBDII Connector. White 16
SIL White 7 Data OBDII Connector. White 16
RDA
Parking Lights White 18 (-) Headlight Switch. White 20
Autolights Green 19 Cut Headlight Switch. White 20
Ignition 1 White 6 (+) Ignition Switch. White 8
Ignition 2 Pink 4 (+) Ignition Switch. White 8
Starter 1 Yellow 8 (+) Ignition Switch. White 8
Starter 2 White 1 (+) Ignition Switch. White 8
12V Blue 7 (+) Ignition Switch. White 8
Not equipped
Wire Information
Not equipped
Connector Information
Not equipped
Not equipped
Not equipped
Not equipped
Type - Vehicle Wiring Reference Chart2
Page 7
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Tire Pressure
Warning ECU
(Behind glove box)
654321
12 11 10 987
18
169
Diagnostic
onnector OBDIIC
Remote
Starter
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
10: (-) GWR (Status) InputBlue/White:
9: (+) Ignition InputPink:
[4]
Autolights Interr. (conn. side): 11Yellow/Red:
[3] (-) Parking Lights , p: in 18Tan
[4]
Autolights Interr. (veh. side): 10Orange/Red:
[]1 (AC) Tach Output: 5Violet/White:
(+) Brake Output: 6Status Gray:
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
SIL: 10Yellow/Black:
[]2
(-) Hood Status Output: 12Blue/Red:
CAN , pHigh: in 6Violet SIL:
in 7Tan, p
CAN Low:
in 14White, p
Headlight
Switch
(+) 12V
(-) Ground
(+) 12V : 13Input Red:
(-) Ground: 14Black:
[3]
Output(-) Parking Lights
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[]2
(-) Hood Status Input
(+) Brake InputStatus
(-) Ground
(-) OutputLock
(-) OutputUnlock
(-) Trunk Release Output
(-) GWR Output
[4]
:, pAutolights in 19Green
Make this connection
only if the vehicle is
equipped with Automatic
Headlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
SIL Interr. (conn. side) : 8Yellow:
SIL Interr. (veh. side) : 9Orange/Yellow:
(-) :Power Liftgate
Red, pin 6
SIL: , p 0in 1Blue
846 27351
Power Liftgate
WhiteSwitch
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output1
CUT
CUT
It is important to make sure you do connect the keysense wire in thNOT is
installation or you will encounter issues when attempting to start the vehicle.
20 19
Not required in D2D mode.
Ignition onnectorC
Fuse Box Connector
Refer to the Vehicle Wiring
Reference Information for wire
and connector details.
4321
8765
1
Installation Type 3
Page 8
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
10
RF
Prog utton.B
LED
4
14
12
2
DBALL2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;
refer to the Vehicle Application Guide for compatibility.
[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Page 9
Type - Vehicle Wiring Reference Chart3
Function Color Pin Polarity Location Color Pins
Toyota Sequoia (G Key) 2011-2014
HS CAN High Violet 6 Data OBDII Connector. Black 16
HS CAN Low White 14 Data OBDII Connector. Black 16
SIL Tan 7 Data OBDII Connector. Black 16
SIL Interrupt Blue 10 Cut
TPMS Connector, behind the glove box. White 12
Parking Lights Tan 18 (-) Headlight Switch. White 20
Autolights Green 19 Cut Headlight Switch. White 20
Ignition 1 Black 6 (+) Ignition Switch. White 8
Ignition 2 Lt. Green 1 (+) Ignition Switch. White 8
Starter 1 Green 7 (+) Ignition Switch. White 8
12V Black 1 (+) Dash Fusebox. White 1
Power Lifgate Red 6 (-) Power Liftgate Switch. White 8
Wire Information Connector Information
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
18
169
Diagnostic
onnectorC
OBDII
Remote
Starter
[3] (-) Parking Lights: , pin 18Lt.Green
(+) Brake: ,Lt. Blue
pin 1
HS CAN :High
in 6Yellow/Black, p
SIL in 7:, pWhite
HS CAN :Low
Blue/White,
pin 14
Tach in 9:, pBlack/White
[1]
Headlight
Switch
(+) 12V
(-) Ground
(+) 12V : 13Input Red:
(-) Ground: 14Black:
[3] (-) Parking Lights Output
(-) Ground
(-) GWR Output
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
10: (-) GWR (Status) InputBlue/White:
9: (+) Ignition InputPink:
SIL: 10Yellow/Black:
[1] (AC) Tach Input
Brake 4-pin
Blue Switch
4
2
3
1
Ignition onnectorC
Refer to the Vehicle Wiring
Reference Information for wire
and connector details.
4321
8765
It is important to make sure you do connect the keysense wire in thNOT is
installation or you will encounter issues when attempting to start the vehicle.
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output2
(+) Starter Output1
Not required in D2D mode.
(-) OutputLock
4[]
(-) OutputUnlock
[]4
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
[]2
(-) Hood Status Output: 12Blue/Red:
(-) Door Status Input
(-) E-Brake Status Input
[]2
(-) Hood Status Input
(+) Brake InputStatus
5
10
4
9
2
7
1
6
3
8
[]4 (-) Lock/Arm:
, pinViolet 4
[]4 (-) Unlock/Disarm:
Green/Black, p 8in
Harness from Driver Side
()Gray or White Connector
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
Installation Type 4
Page 10
[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;
refer to the Vehicle Application Guide for compatibility.
[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[]3 Parking light output only required if Parking Lights are not supported in data.
[4] Remote starter MUST be programmed during flashing to unlock before start and lock after start. This can be done when flashing the firmware under
the Data Feature Configuration section and enabling Safelock under Smart OEM Alarm Control. This Unlock output must also be programmed for double
pulse.
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
10
RF
Prog utton. B
LED
4
14
12
2
DBALL2
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Function Color Pin Polarity Location Color Pins
Toyota Tacoma (G Key) 2011-2015
HS CAN High Yellow/Black 6 Data OBDII Connector. White 16
HS CAN Low Blue/White 14 Data OBDII Connector. Black 16
SIL White 7 Data OBDII Connector. White 16
Tach Black/White 9 Data OBDII Connector. White 16
Parking Lights Green 18 (-) Headlight Switch. White 20
Ignition 1 Black/Red 6 (+) Ignition Switch. White 8
Ignition 2 Blue/Yellow 1 (+) Ignition Switch. White 8
Starter 1 Green/Black 7 (+) Ignition Switch. White 8
Starter 2 Black/White 3 (+) Ignition Switch. White 8
12V White/Red 5 (+) Ignition Switch. White 8
Lock Violet 4 (-) Drivers Kick panel. White or Gray 10
Unlock (double pulse) Green/Black 8 (-) Drivers Kick panel. White or Gray 10
Brake Lt.Blue 1 (+) Brake Switch. Blue 4
Wire Information Connector Information
Type - Vehicle Wiring Reference Chart4
Page 11
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Not required in D2D mode.
It is important to make sure you do connect the keysense wire in th installation or youNOT is
will encounter issues when attempting to start the vehicle.
18
169
Diagnostic
connector OBDII
Remote
Starter
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
10: (-) GWR (Status) InputBlue/White:
9: (+) Ignition InputPink:
[]1 (AC) Tach Output: 5Violet/White:
(+) Brake Output: 6Status Gray:
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
SIL: 10Yellow/Black:
[]2
(-) Hood Status Output: 12Blue/Red:
HS CAN : , pHigh in 6Violet
SIL in 7:, pBlue
HS CAN : , pLow in 14White
(+) 12V
(+) 12V : 13Input Red:
(-) Ground
(-) Ground: 14Black:
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output1
[3]
Output(-) Parking Lights
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[2]
(-) Hood Status Input
(+) Brake InputStatus
(-) Ground
(-) OutputLock
(-) OutputUnlock
(-) Trunk Output
(-) GWR Output
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
Ignition onnectorC
Refer to the Vehicle Wiring
Reference Information for wire
and connector details.
4321
8765
[3] in 13(-) Parking Lights: , pWhite
4
3
2
1
13
12
11 10 9 8 7
6
5
Headlight Switch
[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;
refer to the Vehicle Application Guide for compatibility.
[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[]3 Parking light output only required if Parking Lights are not supported in data.
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
10
DBALL/
DBALL2
RF
Prog utton. B
LED
4
14
12
2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
Installation Type 5
Page 12
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Type 5 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Scion xD 2011-2014
HS CAN High Violet 6 Data OBDII Connector. Black 16
HS CAN Low White 14 Data OBDII Connector. Black 16
SIL Blue 7 Data OBDII Connector. Black 16
RDA Not equipped
Parking Lights White 13 (-) Headlight Switch. White 13
Autolights
Ignition 1 Pink 6 (+) Ignition Switch. White 8
Ignition 2 Green 1 (+) Ignition Switch. White 8
Starter 1 Black 7 (+) Ignition Switch. White 8
Starter 2
12V Yellow 4 (+) Ignition Switch. White 8
Toyota Yaris (G Key) 2011
HS CAN High Violet 6 Data OBDII Connector. White 16
HS CAN Low White 14 Data OBDII Connector White 16
SIL Blue 7 Data OBDII Connector White 16
RDA Not equipped
Parking Lights White 13 (-) Headlight Switch. White 13
Autolights
Ignition 1 Pink 6 (+) Ignition Switch. White 8
Ignitiion 2 Green 1 (+) Ignition Switch. White 8
Starter 1 Black 7 (+) Ignition Switch. White 8
Starter 2
12V Yellow 4 (+) Ignition Switch. White 8
Wire Information Connector Information
Not equipped
Not equipped
Not equipped
Not equipped
Page 13
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
18
169
Diagnostic
onnector OBDIIC
Remote
Starter
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
10: (-) GWR (Status) InputBlue/White:
9: (+) Ignition InputPink:
[4]
Autolights Interr. (conn. side): 11Yellow/Red:
[3] (-) Parking Lights , p: in 18Lt. Blue
[4]
Autolights Interr. (veh. side): 10Orange/Red:
[]1 (AC) Tach Output: 5Violet/White:
(+) Brake Output: 6Status Gray:
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
SIL: 10Yellow/Black:
[]2
(-) Hood Status Output: 12Blue/Red:
HS CAN or , pHigh: in 6Blue Black
SIL:
in 7Gray, p
HS CAN Low:
in 14White, p
Headlight
Switch
(+) 12V
(+) 12V : 13Input Red:
(-) Ground
(-) Ground: 14Black:
[3]
Output(-) Parking Lights
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[]2
(-) Hood Status Input
(+) Brake InputStatus
(-) Ground
(-) OutputLock
(-) OutputUnlock
(-) Trunk Release Output
(-) GWR Output
[4]
Autolights in 19:, pGreen
Make this connection
only if the vehicle is
equipped with Automatic
Headlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
Power Liftgate
WhiteSwitch
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output1
CUT
It is important to make sure you do connect the keysense wire in thNOT is
installation or you will encounter issues when attempting to start the vehicle.
20 19
Not required in D2D mode.
534 21
(-) Power Liftgate:
Red, pin 4
Ignition onnectorC
Refer to the Vehicle Wiring
Reference Information for wire
and connector details.
4321
8765
(+) Starter Output2
Installation Type 6
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
10
RF
Prog utton.B
LED
4
14
12
2
DBALL2
[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;
refer to the Vehicle Application Guide for compatibility.
[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Page 14
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Type 6 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Toyota Highlander (G Key) 2011-2013
HS CAN High Blue 6 Data OBDII Connector. Black 16
HS CAN Low White 14 Data OBDII Connector. Black 16
SIL Gray 7 Data OBDII Connector. Black 16
RDA
Parking Lights Lt. Blue 18 (-) Headlight Switch. White 20
Autolights Green 19 Cut Headlight Switch. White 20
Ignition 1 Black 6 (+) Ignition Switch. White 8
Ignition 2 Lt. Blue 1 (+) Ignition Switch. White 8
Starter 1 Yellow 7 (+) Ignition Switch. White 8
Starter 2 Red or Black 3 (+) Ignition Switch. White 8
12V Red 5 (+) Ignition Switch. White 8
Power Liftgate Red 4 (-) Power Liftgate Switch. Black 5
Toyota Highlander Hybrid (G Key) 2012-2013
HS CAN High Black 6 Data OBDII Connector. Black 16
HS CAN Low White 14 Data OBDII Connector. Black 16
SIL Gray 7 Data OBDII Connector. Black 16
RDA
Parking Lights Lt. Blue 18 (-) Headlight Switch. White 20
Autolights Green 19 Cut Headlight Switch. White 20
Ignition 1 Black 6 (+) Ignition Switch. White 8
Ignition 2 Lt. Blue 1 (+) Ignition Switch. White 8
Starter 1 Yellow 7 (+) Ignition Switch. White 8
Starter 2
12V Green 5 (+) Ignition Switch. White 8
Power Liftgate Red 4 (-) Power Liftgate Switch. Black 5
Not equipped
Not equipped.
Not equipped
Wire Information Connector Information
Page 15
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
4 Aux 1 Right Slide Input: White/Violet: []4
Aux 1 Right Slide Output []4
5 Aux 2 Left Slide Input: Violet/Black: []4
Aux 2 Left Slide Output []4
18
169
Diagnostic
onnectorC
OBDII
Remote
Starter
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
10: (-) GWR (Status) InputBlue/White:
9: (+) Ignition InputPink:
[4]
Autolights Interr. (conn. side): 11Yellow/Red:
[3] (-) Parking Lights , p: in 18Yellow
[4]
Autolights Interr. (veh. side): 10Orange/Red:
[]1 (AC) Tach Output: 5Violet/White:
(+) Brake Output: 6Status Gray:
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
SIL: 10Yellow/Black:
[]2
(-) Hood Status Output: 12Blue/Red:
CAN , pHigh: in 6Red SIL:
in 7White, p
CAN Low:
in 14White, p
Headlight
Switch
(+) 12V
(-) Ground
(+) 12V : 13Input Red:
(-) Ground: 14Black:
[3]
Output(-) Parking Lights
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[]2
(-) Hood Status Input
(+) Brake InputStatus
(-) Ground
(-) OutputLock
(-) OutputUnlock
(-) GWR Output
[4]
Autolights in:, p19Violet
Make this connection
only if the vehicle is
equipped with Automatic
Headlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output1
Ignition onnectorC
Refer to the Vehicle Wiring
Reference Information for wire
and connector details.
4321
8765
CUT
It is important to make sure you do connect the keysense wire in thNOT is
installation or you will encounter issues when attempting to start the vehicle.
20 19
Not required in D2D mode.
RDA: 11Orange/Black:
RDA: ,Pink
pin 26
Body ECU Connector
(middle plug)
456
161718
282930
131415
252627
101112
222324
123
789
192021
Tire Pressure
Warning ECU
(Behind glove box)
654321
12 11 10 987
SIL Interr. (conn. side) : 8Yellow:
SIL Interr. (veh. side) : 9Orange/Yellow:
SIL: , p 0in 1White
CUT
3: (-) Trunk InputRed/White:
(-) Trunk Output
18
Installation Type 7
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
10
RF
Prog utton.B
LED
4
14
12
2
DBALL2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;
refer to the Vehicle Application Guide for compatibility.
[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Page 16
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Type 7 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Toyota Sienna (G key) 2011-2014
HS CAN High Red 6 Data OBDII Connector. White 16
HS CAN Low White 14 Data OBDII Connector. White 16
SIL White 7 Data OBDII Connector. White 16
SIL Interrupt White 10 Cut
TPMS Connector, (located on the left side of the Dash fuse box.) White 12
RDA Pink 26 Data Body ECU. White 30
Parking Lights Yellow 18 (-) Headlight Switch. White 20
Autolights Violet 19 Cut Headlight Switch. White 20
Ignition 1 Black 6 (+) Ignition Switch. White 8
Ignition 2 Yellow 4 (+) Ignition Switch. White 8
Starter 1 Red 8 (+) Ignition Switch. White 8
12V Red 7 (+) Ignition Switch. White 8
Wire Information Connector Information
Page 17
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
18
169
Diagnostic
onnector OBDIIC
Remote
Starter
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
10: (-) GWR (Status) InputBlue/White:
9: (+) Ignition InputPink:
[4]
Autolights Interr. (conn. side): 11Yellow/Red:
[3] (-) Parking Lights or , p: in 18Black White
[4]
Autolights Interr. (veh. side): 10Orange/Red:
[]1 (AC) Tach Output: 5Violet/White:
(+) Brake Output: 6Status Gray:
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
SIL: 10Yellow/Black:
[]2
(-) Hood Status Output: 12Blue/Red:
HS CAN , pHigh: in 6Blue SIL:
in 7Gray, p
HS CAN Low:
in 14White, p
Headlight
Switch
(+) 12V
(-) Ground
(+) 12V : 13Input Red:
(-) Ground: 14Black:
[3]
Output(-) Parking Lights
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[]2
(-) Hood Status Input
(+) Brake InputStatus
(-) Ground
(-) OutputLock
(-) OutputUnlock
(-) GWR Output
[4]
:, p20Autolights inGreen
Make this connection
only if the vehicle is
equipped with Automatic
Headlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output2
(+) Starter Output1
Ignition onnectorC
Refer to the Vehicle Wiring
Reference Information for wire
and connector details.
4321
8765
CUT
It is important to make sure you do connect the keysense wire in thNOT is
installation or you will encounter issues when attempting to start the vehicle.
20 19
Not required in D2D mode.
RDA: 11Orange/Black:
RDA: ,Blue
pin 61
Body ECU Connector
(middle plug)
456
161718
282930
131415
252627
101112
222324
123
789
192021
3: (-) Trunk InputRed/White:
(-) Trunk Output
Installation Type 8
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
10
RF
Prog utton.B
LED
4
14
12
2
DBALL2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;
refer to the Vehicle Application Guide for compatibility.
[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Page 18
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Type 8 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Toyota Camry (G Key) 2012-2014
HS CAN High Blue 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
SIL Gray 7 Data
OBDII. Black 16
RDA Blue 16 Data Body ECU. White 30
Parking Lights Black or White 18 (-) Headlight switch. White 20
Autolights Green 20 Cut Headlight switch White 20
12V Green 5 (+) Ignition switch. White 8
Accessory White 2 (+) Ignition switch. White 8
Ignition 1 Black 6 (+) Ignition switch. White 8
Ignition 2 Pink 1 (+) Ignition switch. White 8
Starter 1 Blue 7 (+) Ignition switch. White 8
Starter 2 Lt.Green 3 (+) Ignition switch. White 8
Wire Information Connector Information
Page 19
Rev.: 20 914170
Platform: DBALL2
Firmware TL7:
© 2017 Directed. All rights reserved.
Tire Pressure
Warning ECU
(Behind glove box)
654321
12 11 10 987
18
169
Diagnostic
onnector OBDIIC
Remote
Starter
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
10: (-) GWR (Status) InputBlue/White:
9: (+) Ignition InputPink:
[4]
Autolights Interr. (conn. side): 11Yellow/Red:
[3] (-) Parking Lights , p: in 18Tan
[4]
Autolights Interr. (veh. side): 10Orange/Red:
[]1 (AC) Tach Output: 5Violet/White:
(+) Brake Output: 6Status Gray:
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
SIL: 10Yellow/Black:
[]2
(-) Hood Status Output: 12Blue/Red:
CAN , pHigh: in 6Violet SIL:
in 7Tan, p
CAN Low:
in 14White, p
Headlight
Switch
(+) 12V
(-) Ground
(+) 12V : 13Input Red:
(-) Ground: 14Black:
[3]
Output(-) Parking Lights
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[]2
(-) Hood Status Input
(+) Brake InputStatus
(-) Ground
(-) OutputLock
(-) OutputUnlock
(-) GWR Output
[4]
:, pAutolights in 19Green
Make this connection
only if the vehicle is
equipped with Automatic
Headlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
SIL Interr. (conn. side) : 8Yellow:
SIL Interr. (veh. side) : 9Orange/Yellow:
SIL: , p 0in 1Blue
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output1
CUT
CUT
It is important to make sure you do connect the keysense wire in thNOT is
installation or you will encounter issues when attempting to start the vehicle.
20 19
Not required in D2D mode.
Ignition onnectorC
Fuse Box Connector
Refer to the Vehicle Wiring
Reference Information for wire
and connector details.
4321
8765
1
Installation Type 9
Page 20
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
10
RF
Prog utton.B
LED
4
14
12
2
DBALL2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;
refer to the Vehicle Application Guide for compatibility.
[]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
/