Kichler Lighting 16232AZT30 User manual

Brand
Kichler Lighting
Model
16232AZT30
Type
User manual

This manual is also suitable for

For warranty informaon please visit: hp://www.kichler.com/warranty
Para informacion de la garana por favor visite: hp://www.kichler.com/warranty
IS-16232-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Kichler 16232 & 16233 Installaon Guide
LED Wall Pack
IMPORTANT: Read before removing xture from carton. Retain
for future reference.
SAFETY: This xture must be wired in accordance with the
NATIONAL ELECTRICAL CODE (NEC) and applicable local codes
and ordinances. A person familiar with the construcon and
operaon of the product and the hazards involved must install
this product. A qualied licensed electrician should complete all
work. Proper grounding is required for safety.
WARNING: Make certain power is OFF before installing or
maintaining xture.
RISK OF INJURY: Fixture may become damaged and/or unstable
if not installed properly.
Cauons:
Installaon Instrucons:
Fixture Diagram
NOTE: Turn o electrical supply at the breaker. Follow all
local electrical codes for wiring and grounding requirements.
NOTE: This xture is intended to be surface mounted on to a
wall in the lens down posion.
Tools Required: Phillips Screw Driver, Security Torx T-20 Bit
& Driver, Electric Drill, Drill Bit Set, Wire Strippers & Cuers
1) Unpack xture and ensure that there are no damaged
parts.
2) Open xture by removing the T-20 Security Torx screws on
the side of the xture.
3) Disconnect orange connector and remove LED and frame
assembly to allow for easier installaon.
4) Inspect the 3 mounng hole locaons (Item A on g. 2)
and ensure that there are no components over them.
5) In order to mount the xture the backplate has to be
pierced at the mounng locaons. Use an appropriate
sized drill bit for the mounng screws up to 5/16”.
6) Align the backplate and mount securely with mounng
hardware appropriate for surface.
7) If electrical connecons are going to be made from a
conduit pipe, remove one of the conduit plugs from the
base and thread NPS conduit pipe into locaon.
8) If electrical connecons are going to be made through a
juncon box, drill the appropriate holes (Item C in Fig.2)
for the sized juncon box.
9) Connect leads from back of xture to the power supply
leads: Green to green (ground), black to black (hot), white
to white(neutral).
10) Reaach frame and glass assembly to base by slipping it
over the barrel pins.
11) Reconnect orange connector and reaach the frame
assembly using the Torx Screw.
MOUNTING:
The back plate has a cast-in drill and knock-out template
to match any standard recessed juncon box, three 5/16”
knock-outs for mounng holes A and three 1/2” NPS
tapped holes D for surface conduit or photocontrol unit.
A – 5/16” Diameter Knockouts
B – 9/16” Diameter Knockouts
C – Knockouts for #10 screw
D – 1/2” NPS Tapped Holes
Use weatherproof silicone sealant to seal all holes and
gaps between xture and mounng surface.
This device complies with part 15 of the FCC Rules. Operaon is
subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including
interference that may cause undesired operaon.
Note: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instrucons,
may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur
in a parcular installaon. If this equipment does cause harmful
interference to radio or television recepon, which can be
determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
FCC Informaon:
RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK
• This product should be installed, inspected, and maintained by a qualied
electrician only, in accordance with the NEC (Naonal Electric Code) and all
local codes.
• Turn o electrical power before inspecon, installaon or removal.
• Use only UL (or other NRTL) approved wire for input/output connecons.
Minimum size 18 AWG or 14 AWG for connuous runs.
• Make sure LEDs and drivers are cool to touch when performing maintenance.
Make sure the supply voltage is the same as the rated voltage of the luminaire.
• Do not install in a hazardous atmosphere, except where the ambient
temperature does not exceed the rated operang temperature of the xture.
• Keep ghtly closed when in operaon
Electrical Requirements
The LED driver must be supplied with 120 to
277V, 50/60 Hz and connected to an individual,
properly grounded branch circuit protected by a
20 Ampere circuit breaker. Use min. 90°C supply.
Grounding Instrucons
The grounding and bonding of the overall
system shall be done in accordance with
NEC Arcle 600 and local codes
INSTALLATION AND SERVICE INSTRUCTIONS
SML-106/706/707/708 LED Wallpack
TEMPLATE
GR
GR
GND
A
A
A
C
B
31/4" OCT.BOX
4" OCT. BOX
D
D
D
TROUBLE ING CHECKLIST: If the light does not work.
Figure 2
Figure 1
Black
Line
White
Neutral
Green
Ground
FIXTURE
Page is loading ...
IS-16232-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Kichler 16232 & 16233 Installaon Guide
LED Wall Pack
IMPORTANT: Read before removing xture from carton. Retain
for future reference.
SAFETY: This xture must be wired in accordance with the
NATIONAL ELECTRICAL CODE (NEC) and applicable local codes
and ordinances. A person familiar with the construcon and
operaon of the product and the hazards involved must install
this product. A qualied licensed electrician should complete all
work. Proper grounding is required for safety.
WARNING: Make certain power is OFF before installing or
maintaining xture.
RISK OF INJURY: Fixture may become damaged and/or unstable
if not installed properly.
Cauons:
Installaon Instrucons:
Fixture Diagram
NOTE: Turn o electrical supply at the breaker. Follow all
local electrical codes for wiring and grounding requirements.
NOTE: This xture is intended to be surface mounted on to a
wall in the lens down posion.
Tools Required: Phillips Screw Driver, Security Torx T-20 Bit
& Driver, Electric Drill, Drill Bit Set, Wire Strippers & Cuers
1) Unpack xture and ensure that there are no damaged
parts.
2) Open xture by removing the T-20 Security Torx screws on
the side of the xture.
3) Disconnect orange connector and remove LED and frame
assembly to allow for easier installaon.
4) Inspect the 3 mounng hole locaons (Item A on g. 2)
and ensure that there are no components over them.
5) In order to mount the xture the backplate has to be
pierced at the mounng locaons. Use an appropriate
sized drill bit for the mounng screws up to 5/16”.
6) Align the backplate and mount securely with mounng
hardware appropriate for surface.
7) If electrical connecons are going to be made from a
conduit pipe, remove one of the conduit plugs from the
base and thread NPS conduit pipe into locaon.
8) If electrical connecons are going to be made through a
juncon box, drill the appropriate holes (Item C in Fig.2)
for the sized juncon box.
9) Connect leads from back of xture to the power supply
leads: Green to green (ground), black to black (hot), white
to white(neutral).
10) Reaach frame and glass assembly to base by slipping it
over the barrel pins.
11) Reconnect orange connector and reaach the frame
assembly using the Torx Screw.
MOUNTING:
The back plate has a cast-in drill and knock-out template
to match any standard recessed juncon box, three 5/16”
knock-outs for mounng holes A and three 1/2” NPS
tapped holes D for surface conduit or photocontrol unit.
A – 5/16” Diameter Knockouts
B – 9/16” Diameter Knockouts
C – Knockouts for #10 screw
D – 1/2” NPS Tapped Holes
Use weatherproof silicone sealant to seal all holes and
gaps between xture and mounng surface.
This device complies with part 15 of the FCC Rules. Operaon is
subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including
interference that may cause undesired operaon.
Note: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instrucons,
may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur
in a parcular installaon. If this equipment does cause harmful
interference to radio or television recepon, which can be
determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
FCC Informaon:
RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK
• This product should be installed, inspected, and maintained by a qualied
electrician only, in accordance with the NEC (Naonal Electric Code) and all
local codes.
• Turn o electrical power before inspecon, installaon or removal.
• Use only UL (or other NRTL) approved wire for input/output connecons.
Minimum size 18 AWG or 14 AWG for connuous runs.
• Make sure LEDs and drivers are cool to touch when performing maintenance.
Make sure the supply voltage is the same as the rated voltage of the luminaire.
• Do not install in a hazardous atmosphere, except where the ambient
temperature does not exceed the rated operang temperature of the xture.
• Keep ghtly closed when in operaon
Electrical Requirements
The LED driver must be supplied with 120 to
277V, 50/60 Hz and connected to an individual,
properly grounded branch circuit protected by a
20 Ampere circuit breaker. Use min. 90°C supply.
Grounding Instrucons
The grounding and bonding of the overall
system shall be done in accordance with
NEC Arcle 600 and local codes
INSTALLATION AND SERVICE INSTRUCTIONS
SML-106/706/707/708 LED Wallpack
TEMPLATE
GR
GR
GND
A
A
A
C
B
31/4" OCT.BOX
4" OCT. BOX
D
D
D
TROUBLE ING CHECKLIST: If the light does not work.
Figure 2
Figure 1
Black
Line
White
Neutral
Green
Ground
FIXTURE
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Kichler Lighting 16232AZT30 User manual

Brand
Kichler Lighting
Model
16232AZT30
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents