Kichler Lighting 16232AZT30 User manual

For warranty informaon please visit: hp://www.kichler.com/warranty

Para informacion de la garana por favor visite: hp://www.kichler.com/warranty

IS-16232-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

Kichler 16232 & 16233 Installaon Guide

LED Wall Pack

IMPORTANT: Read before removing xture from carton. Retain

for future reference.

SAFETY: This xture must be wired in accordance with the

NATIONAL ELECTRICAL CODE (NEC) and applicable local codes

and ordinances. A person familiar with the construcon and

operaon of the product and the hazards involved must install

this product. A qualied licensed electrician should complete all

work. Proper grounding is required for safety.

WARNING: Make certain power is OFF before installing or

maintaining xture.

RISK OF INJURY: Fixture may become damaged and/or unstable

if not installed properly.

Cauons:

Installaon Instrucons:

Fixture Diagram

NOTE: Turn o electrical supply at the breaker. Follow all

local electrical codes for wiring and grounding requirements.

NOTE: This xture is intended to be surface mounted on to a

wall in the lens down posion.

Tools Required: Phillips Screw Driver, Security Torx T-20 Bit

& Driver, Electric Drill, Drill Bit Set, Wire Strippers & Cuers

1) Unpack xture and ensure that there are no damaged

parts.

2) Open xture by removing the T-20 Security Torx screws on

the side of the xture.

3) Disconnect orange connector and remove LED and frame

assembly to allow for easier installaon.

4) Inspect the 3 mounng hole locaons (Item A on g. 2)

and ensure that there are no components over them.

5) In order to mount the xture the backplate has to be

pierced at the mounng locaons. Use an appropriate

sized drill bit for the mounng screws up to 5/16”.

6) Align the backplate and mount securely with mounng

hardware appropriate for surface.

7) If electrical connecons are going to be made from a

conduit pipe, remove one of the conduit plugs from the

base and thread NPS conduit pipe into locaon.

8) If electrical connecons are going to be made through a

juncon box, drill the appropriate holes (Item C in Fig.2)

for the sized juncon box.

9) Connect leads from back of xture to the power supply

leads: Green to green (ground), black to black (hot), white

to white(neutral).

10) Reaach frame and glass assembly to base by slipping it

over the barrel pins.

11) Reconnect orange connector and reaach the frame

assembly using the Torx Screw.

MOUNTING:

The back plate has a cast-in drill and knock-out template

to match any standard recessed juncon box, three 5/16”

knock-outs for mounng holes A and three 1/2” NPS

tapped holes D for surface conduit or photocontrol unit.

A – 5/16” Diameter Knockouts

B – 9/16” Diameter Knockouts

C – Knockouts for #10 screw

D – 1/2” NPS Tapped Holes

Use weatherproof silicone sealant to seal all holes and

gaps between xture and mounng surface.

This device complies with part 15 of the FCC Rules. Operaon is

subject to the following two condions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including

interference that may cause undesired operaon.

Note: This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protecon

against harmful interference in a residenal installaon. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instrucons,

may cause harmful interference to radio communicaons.

However, there is no guarantee that interference will not occur

in a parcular installaon. If this equipment does cause harmful

interference to radio or television recepon, which can be

determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

FCC Informaon:

RISK OF FIRE, EXPLOSION AND ELECTRIC SHOCK

• This product should be installed, inspected, and maintained by a qualied

electrician only, in accordance with the NEC (Naonal Electric Code) and all

local codes.

• Turn o electrical power before inspecon, installaon or removal.

• Use only UL (or other NRTL) approved wire for input/output connecons.

Minimum size 18 AWG or 14 AWG for connuous runs.

• Make sure LEDs and drivers are cool to touch when performing maintenance.

Make sure the supply voltage is the same as the rated voltage of the luminaire.

• Do not install in a hazardous atmosphere, except where the ambient

temperature does not exceed the rated operang temperature of the xture.

• Keep ghtly closed when in operaon

Electrical Requirements

The LED driver must be supplied with 120 to

277V, 50/60 Hz and connected to an individual,

properly grounded branch circuit protected by a

20 Ampere circuit breaker. Use min. 90°C supply.

Grounding Instrucons

The grounding and bonding of the overall

system shall be done in accordance with

NEC Arcle 600 and local codes

INSTALLATION AND SERVICE INSTRUCTIONS

SML-106/706/707/708 LED Wallpack

TEMPLATE

GND

31/4" OCT.BOX

4" OCT. BOX

TROUBLE ING CHECKLIST: If the light does not work.

Figure 2

Figure 1

Black

Line

White

Neutral

Green

Ground

FIXTURE

Page is loading ...

IS-16232-CB