CAB Flag applicator 4712 User manual

Brand: CAB

Model: Flag applicator 4712

Type: User manual

This manual is also suitable for

HERMES Q / Hermes+ applicators

Made in Germany

4712

Flag Applicator

Service Manual

2 2

Family Type

Flag Applicator 4712L-300

Edition: 02/2017 - Part No. 9009954

This documentation as well as translation hereof are property of cab Produkttechnik GmbH & Co. KG.

The replication, conversion, duplication or divulgement of the whole manual or parts of it for other intentions than its original

intended purpose demand the previous written authorization by cab.

Editor

Regarding questions or comments please contact cab Produkttechnik GmbH & Co. KG.

Topicality

Due to the constant further development of our products discrepancies between documentation and products can occur.

Please check www.cab.de for the latest update.

Terms and conditions

Deliveries and performances are effected under the General conditions of sale of cab.

Service Manual

for the following product

Germany

cab Produkttechnik

GmbH & Co KG

Postfach 1904

D-76007 Karlsruhe

Wilhelm-Schickard-Str. 14

D-76131 Karlsruhe

Telefon +49 721 6626-0

Telefax +49 721 6626-249

www.cab.de

[email protected]

France

cab technologies s.a.r.l.

F-67350 Niedermodern

Téléphone +33 388 722 501

www.cab.de/fr

[email protected]

USA

cab Technology Inc.

Tyngsboro MA, 01879

Phone +1 978 649 0293

www.cab.de/us

[email protected]

Asia

cab Technology Co., Ltd.

Junghe, Taipei, Taiwan

Phone +886 2 8227 3966

www.cab.de/tw

[email protected]

China

cab (Shanghai)Trading Co., Ltd.

Phone +86 21 6236-3161

www.cab.de/cn

[email protected]

Further representation on request

1 Introduction ............................................................................................................................................ 4

1.1 Instructions ...............................................................................................................................................4

1.2 Intended Use ............................................................................................................................................4

1.3 Safety Instructions ....................................................................................................................................4

1.4 Safety Markings .......................................................................................................................................5

1.5 Environment .............................................................................................................................................5

2 Product Description ...............................................................................................................................6

2.1 Important Features ...................................................................................................................................6

2.2 Technical Data ..........................................................................................................................................6

2.3 Product Overview without Cover ..............................................................................................................7

2.4 Contents of Delivery .................................................................................................................................9

3 Operation .............................................................................................................................................. 10

3.1 Standard Operation ................................................................................................................................10

3.2 Cleaning .................................................................................................................................................10

4 Error Messages .................................................................................................................................... 12

4.1 Error Messages of the Printer ................................................................................................................ 12

4.2 Error messages of the applicator ........................................................................................................... 12

5 Licenses ................................................................................................................................................13

5.1 Declaration of Incorporation ...................................................................................................................13

5.2 EU Declaration of Conformity .................................................................................................................14

6 Installation ............................................................................................................................................ 15

6.1 Default Factory Values. ..........................................................................................................................15

6.2 Required Space ....................................................................................................................................15

6.3 Tools .......................................................................................................................................................16

6.4 Mounting and Demounting the Cover ....................................................................................................16

6.5 Mounting the Applicator ..........................................................................................................................17

6.6 Releasing the Transportation Lock .........................................................................................................17

6.7 Mounting the Blow Tube .........................................................................................................................18

6.8 Connecting the Air Pressure ..................................................................................................................18

6.9 Mounting the Suction Pads .................................................................................................................... 19

6.10 Preparing the Tamp Assembly for Adjustments ......................................................................................19

7 Adjustments .........................................................................................................................................20

7.1 Adjustments to the Tamp ........................................................................................................................20

7.2 Alignment of the Product to the Applicator .............................................................................................22

7.3 Setting the Application height .................................................................................................................23

7.4 Adjusting the Vacuum ............................................................................................................................24

7.5 Adjustments to the Blowpipe (Supporting Air) ........................................................................................25

7.6 Adjustment to the Speed of Cylinder Z ..................................................................................................27

7.7 Settings of the Sensors of Cylinder Z .....................................................................................................28

7.8 Setting of the End Position Dampener ...................................................................................................29

7.9 Settings for Movement in Direction Z .....................................................................................................29

8 ConguringthePrinter ........................................................................................................................30

8.1 MethodofChangingtheConguration ..................................................................................................30

8.2 Quick Selection Mode for the Setting of Delay Times ............................................................................30

8.3 CongurationParametersoftheApplicator ...........................................................................................31

8.4 Adjustments to the Dispensing Offset .................................................................................................... 32

8.5 Activating the Peel-off Mode .................................................................................................................. 32

9 Operation .............................................................................................................................................. 33

9.1 Test Mode without a Print Job ................................................................................................................33

9.2 Test Mode with Print Job ........................................................................................................................33

10 Spare Parts ........................................................................................................................................... 34

10.1 Retainer Assembly ................................................................................................................................. 34

10.2 Pneumatic Retainer Assembly ............................................................................................................... 35

10.3 Electronic Retainer Assembly ................................................................................................................36

10.4 Cylinder Guidance Assembly ................................................................................................................. 37

10.5 Cylinder Assembly Group X/Y ................................................................................................................38

10.6 Tamp Assembly ......................................................................................................................................39

11 Illustrations ...........................................................................................................................................40

11.1 Block Diagram ........................................................................................................................................40

11.2 Pneumatic Illustration Type 4712 ..........................................................................................................41

12 Index ......................................................................................................................................................42

Table of content

4 4

1 Introduction

1.1 Instructions

Important information and instructions in this documentation are designated as follows:

Danger!

Draws attention to an exceptionally great, imminent danger to your health or life due to hazardous

voltages.

Danger!

Draws attention to a danger with high risk which, if not avoided, may result in death or serious injury.

Warning!

Draws attention to a danger with medium risk which, if not avoided, may result in death or serious injury.

Caution!

Draws attention to a danger with low risk which, if not avoided, may result in minor or moderate injury.

Attention!

Draws attention to potential risks of property damage or loss of quality.

Note!

Advice to make work routine easier or on important steps to be carried out.



Environment!

Gives you tips on protecting the environment.



Handling instruction



Reference to section, position, illustration number or document.



Option(accessories,peripheralequipment,specialttings).

Time

Information in the display.

1.2 Intended Use

• The device is manufactured in accordance with the current technological status and the recognized safety rules.

However, danger to life and limb of the user or third parties and/or damage to the device and other tangible assets

can arise during use.

• The device may only be used for its intended purpose and if it is in perfect working order, and it must be used with

regard to safety and dangers as stated in the operating manual.

• The device applicator mounted on a cab printer of the Hermes+ series is intended exclusively for applying suitable

materials that have been approved by the manufacturer. Any other use or use going beyond this shall be regarded

as improper use. The manufacturer/supplier shall not be liable for damage resulting from unauthorized use; the

user shall bear the risk alone.

• Usage for the intended purpose also includes complying with the operating manual, including the manufacturer‘s

maintenancerecommendationsandspecications.

Note!

The complete and current version of the documentation can be found in the Internet.

1.3 Safety Instructions

Attention!

Initiation,adjustmentsandchangingofpartsaretobeperformedbyqualiedservicepersonnelonly.

Warning!

This is a class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

• Before mounting the delivered components disconnect the printer from the power supply and close the shutoff

valve of the applicator.

• Only connect the device to other devices which have a protective low voltage.

• Switch off all affected devices (computer, printer, accessories) before connecting or disconnecting.

• In operation, moving parts are easily accessible.

This applies especially for the zone, where the pad is moved between the starting and the labelling position.

During operation do not reach into that zone and keep long hair, loose clothes, and jewelry distant. Before any

manipulations in those areas, close the shutoff valve.

• The device may only be used in a dry environment, do not expose it to moisture (sprays of water, mists, etc.).

• Do not use the device in an explosive atmosphere.

• Do not use the device close to high-voltage power lines.

• Perform only those actions described in this operating manual.

Work going beyond this may only be performed by trained personnel or service technicians.

• Unauthorized interference with electronic modules or their software can cause malfunctions.

• Otherunauthorizedworkonormodicationstothedevicecanalsoendangeroperationalsafety.

• Alwayshaveserviceworkdoneinaqualiedworkshop,wherethepersonnelhavethetechnicalknowledgeand

tools required to do the necessary work.

• There are various warning stickers on the device. They draw your attention to dangers. Warning stickers must

therefore not be removed, as then you and other people cannot be aware of dangers and may be injured.

1.4 Safety Markings

1: Risk of injuries by moving parts!

2: The cylinder is under pressure

also if the printer is switched off.

Possibility of residual energy!

Danger of crushing hands and

ngersbythemovingpad!

Attention!

Never remove or cover safety markings!

Replace it in case of damage!

Fig. 1 Safety marking

1.5 Environment



Obsolete devices contain valuable recyclable materials that should be sent for recycling.

 Send to suitable collection points, separately from residual waste.

The modular construction of the applicator enables it to be easily disassembled into its component parts.

 Send the parts for recycling.

1 Introduction

6 6

2 Product Description

2.1 Important Features

• The supporting air and the vacuum as well as the speed of the cylinder are adjustable. That way the applicator

can be adapted to different label materials and sizes.

• To avoid contamination within the vacuum channels they are cleaned by air pressure impulses at the end of each

application.

• For operation in a system the I/O interface of the printer can be used.

2.2 Technical Data

Front RearDiameter x Pi (π)

L LD (Ø) x Pi (π)

Flag length LFlag length L

Fig. 2 Applicator parameters

Label transfer Label type

4712 L 300

Label width Hermes

4 mm 60 -100

Label height mm 10 - 50

Diameter

mm 3 - 20

Working pressure MPa 0,45 (4,5 bar)

Sound pressure levels unter 74 dB(A)

Product during labeling xed

Labeling of the product from above

from below

from the side

Product height xed

Product to the lower edge

at the cylinder stroke 300 up to mm 260

Immersion depth of tongs mm 55

Offset P mm max. 0,5 - 1

Lateral displacement mm max. 0,2

Cycle time approx. cylces/min. 15 ~/min 15

Table 1 Technical data

2 Product Description

2.3 Product Overview without Cover

Front view

Throttle valve vacuum/support air

support air

vacuum

Fig. 3 Product overview - front view

1 Throttle valve cylinder - retraction motion z-direction

2 Stopper for blowing mode and transportation

3 Thumbscrewforxingtheapplicatortotheprinter

4 Setting screw for the angle between the printer and

the applicator

5 Compressed air connector

6 Shutoff valve

7 Setting screw for the height of the cylinder group

8 Throttle valve cylinder - extends in z-direction

9 Setting crew for the sideways stamp position

10 Stamp group

11 Blow tube

12 Throttle valve for pressure

13 Throttle valve for vacuum

8 8

2 Product Description

Rear view

Fig. 4 Product overview - rear view

Fig. 5 Product Overview - Control Unit

Throttle valve cylinder - retraction motion z-direction

Throttle valve cylinder - extension motion z-direction

Stamp(userdened)

Blow tube for pressure

Safety for hinge

Throttle valve cylinder - retraction lock

Printer connector

Throttle valve cylinder - extension lock

Magnetic valve cylinder z

Magnetic valve cylinder lock

Magnetic valve compressed air

Magnetic valve vacuum and pressure

Circuit board - applicator control

Circuit board - applicator connections

Vacuum valve

Valves and settings

2 Product Description

2.4 Contents of Delivery

1 Applicator with mounted pad

2 Blow tube for supporting air

(depending on the used printer)

3 Documentation

Fig. 6 Contents of delivery

Note!

Please keep the original packaging in case the applicator must be returned.

Attention!

The device as well as the printing materials will be damaged by moisture and wetness.

 Set up label printer with applicator only in dry locations protected from moisture and splashes.

10 10

3 Operation

3.1 Standard Operation

 Check all external connections.

 Load the material. Ensure that the locking system is locked  Operator's Manual of the printer.

 Open the shutoff valve of the air pressure.

Attention!

 Ensure that the pad is not covered by a label when switching on the printer-applicator system.

Otherwise the vacuum sensor may not be calibrated correctly.

 Switch on the printer.

Note!

In the case of the tamp being outside the start position when switching on the printer the print process will

be interrupted and an error message will be shown on the display.

If you push the pause button on the printer the applicator will move into the start position.

The Applicator is ready for work.

 Press the feed key on the printer.

A synchronization feed is released. The processed labels have to be removed manually. After a few seconds the

printer carries out a short backward feed to position the front edge of the next label at the printing line.

Note!

This synchronizing also has to be carried out when the print job has been interrupted with the cancel key.

Synchronizing is not necessary when the print head was not lifted between print jobs. This also applies if

the printer was powered off between print jobs.

 Start a print job

 Start the labelling process via I/O interface.

Error messages during labelling process are shown in the display of the printer

 4 Error Messages.

3.2 Cleaning

Attention!

 Never use solvent or abrasive.

 Clean the outside surfaces with multi purpose cleaner.

 Removing dust particles and leftover label pieces with a

soft brush and/or vacuum cleaner.

 The slide foil (1) requires regular cleaning as the most dirt

is deposited here.

Fig. 7 Cleaning of the tamp

3 Operation

Fig. 8 Mounting/demounting the applicator on/from the printer

Attention!

Initiation,adjustmentsandchangingofpartsistobeperformedbyqualiedservicepersonnelonly.

 Service Manual Applicator

Attention!

 Disconnect the printer from the power supply before mounting the applicator!

 Ensure the printer is in a stable position!

 Connect the compressed air only after mounting the applicator to the printer!

To clean the applicator and printer it is occasionally necessary to turn away or even demount the applicator from the

printer.

Do not adjust the setting screws, throttle valves or other alignment elements. This will enable use of the applicator

directly after cleaning

Turning away & Demounting the applicator

1. To turn away the applicator loosen thumbscrew (5) and swing the applicator to the side.

2. Disconnect SUB-D 15 male connector (6) from the female connector (7) of the printer.

3. Loosen screw (4) and move the locking plate (3) from the hinges.

4. Lift the applicator upward and off the printer.

Remounting the applicator

1. Hang the applicator via the female part (1) of hinges to the male printer mounted hinges parts (2).

2. Connect SUB-D 15 male connector (6) to the female connector (7) of the printer.

3. To secure the applicator slide the locking plate (3) under the hinge and tighten the screw (4).

4. Swing the applicator to the printer and tighten the thumbscrew (5).

12 12

4 Error Messages

4.1 Error Messages of the Printer

For detailed information about printer errors (e.g. 'Paper out', 'Ribbon out', etc.)  Check the operator's manual of the

printer.

Error treatment:

 Clearing the error results.

 Press the feed key to synchronize the label feed, remove the left over labels manually.

 Press the pause key to quit the error state.

After error correction, the label causing the error will be reprinted.

4.2 Error messages of the applicator

Thefollowingtablecontainsanoverviewofapplicatorspecicerrormessagesandtheirpossiblecauses.Italso

suggests methods to resolve the problems:

Error Message Possible Cause

Air pressure ins.

Compressed air is switched off

Pressure too low < 4 bar

Pressure is too high > 6 bar

Label not depos.

Label has not been placed onto the product; after the pad has moved back the label is

still sticking to the pad.

Lower position

Pad has not reached the starting position within 2s after its has left the labelling position;

or pad has left the starting position unauthorized

Process Error

Process of labeling was interrupted via the I/O interface of the printer with the XSTP

signal.

Re. sensor blk.

There has been no change of the switch state at the upper sensor at the cylinder

between the start of the labelling process and the signal from the labelling position

sensor.

Upper position

Pad is not in the starting position when the printer is switched on.

Pad has not reached the labelling position within 2s after the movement of the pad was

started.

Pad has left the printing position without authorization.

Vac. plate empty

Label has not been picked up properly by the pad; or label fell off the pad before it could

be placed onto the product.

Table 2 Error messages of the applicator

Error treatment:

 Clear the error results

 Press the pause key to quit the error state.

Note!

In the case of errors check the Service Manual for adjustment and settings.

Warning!

After the error has been resolved the application array will immediately move back to the starting position!

Dangerofcrushinghandsandngersbythemovingparts!

 Do not reach into the zone of the moving parts and keep long hair, loose clothes, and jewelry away.

After error correction, the print of the label causing the error cannot be repeated without re-starting the print job

except the error "Vac. plate empty" . In this case, the last label will be printed again after resolution via the

pause key and then pressing the Enter button

 Intheapplicationmode"Apply/Print"sendsthesignal"Printrstlabel"orpressthebutton to send a printed

label to the stamp.

5 Licenses

5.1 Declaration of Incorporation

cab Produkttechnik

GmbH & Co KG

Wilhelm-Schickard-Str. 14

D-76131 Karlsruhe

Germany

Declaration of Incorporation

We declare herewith that the following „partly completed machinery“ as a result of design, construction and the version

put in circulation complies with the essential requirements of the Directive 2006/42/EC on machinery :

Annex I, Article 1.1.2, 1.1.3, 1.1.5, 1.1.6, 1.2.1, 1.3.2, 1.5.2, 1.5.8, 1.6.3, 1.7

In the event of any alteration which has not been approved by us being made to any device as designated below, this

statement shall thereby be made invalid.

Device: Flag Applicator

Type: 4712

Applied EU Regulations Applied Standards

Directive 2006/42/EC on machinery

• EN ISO 12100:2010

• EN ISO 13849-1:2008

• EN 60950-1:2006

+A11:2009+A12:2011+A1:2010+A2:2013

Personauthorisedtocompilethetechnicalle: Erwin Fascher

Am Unterwege 18/20

99610 Sömmerda

Signed for, and on behalf of the Manufacturer:

cab Produkttechnik Sömmerda

Gesellschaft für Computer-

und Automationsbausteine mbH

99610 Sömmerda

Sömmerda, 18.10.2016

Erwin Fascher

Managing Director

Theproductmustnotbeputintoserviceuntilthenalmachineryintowhichitistobeincorporatedhasbeendeclaredin

conformity with the provisions of the Directive on machinery

The documents according annex VII part B from the incomplete machinery are created and will commit to state agencies

on request in electronic kinds.

14 14

5 Licenses

5.2 EU Declaration of Conformity

cab Produkttechnik

GmbH & Co KG

Wilhelm-Schickard-Str. 14

D-76131 Karlsruhe

Germany

EU Declaration of Conformity

We declare herewith that as a result of the manner in which the device designated below was designed, the type of

construction and the devices which, as a result have been brought on to the general market comply with the relevant

fundamental regulations of the EU Rules for Safety and Health. In the event of any alteration which has not been

approved by us being made to any device as designated below, this statement shall thereby be made invalid.

Device: Flag Applicator

Type: 4712

Applied EU Regulations Applied Standards

Directive 2014/30/EU relating to electromagnetic compatibility

• EN 55022:2010

• EN 55024:2010

• EN 61000-6-2:2005

Directive 2011/65/EU on the restriction of the use of certain

hazardous substances in electrical and electronic equipment

• EN 50581:2012

Signed for, and on behalf of the Manufacturer :

cab Produkttechnik Sömmerda

Gesellschaft für Computer-

und Automationsbausteine mbH

99610 Sömmerda

Sömmerda, 18.10.2016

Erwin Fascher

Managing Director

6 Installation

6.1 Default Factory Values.

Note!

The applicators are set up with default parameters. Keeping these settings will guarantee frictionless

usability.

Note!

Whenusingtheapplicatorforclientspeciedjobsacustomcongurationisinstalled.

Thustheperformancewillbemeasuredbythevaluesofthecommissioningcerticateandnotthestandard

values.

The standard values for the default settings are as follows:

- standing connection to a cab Hermes+ printer

- continuous air pressure of 0,45 MPa (4,5 bar)

6.2 Required Space

35°

approx. 42 mm

Printing direction

Fig. 9 Disengaging or pivoting the applicator

For maintenance or disassembly the applicator needs to be pivoted a minimum of 35°.

Thus a minimum of 42 mm on the hinge side of the applicator is needed.

The required space needed by the applicator in the direction of printing is dependent on the tamp.

16 16

6.3 Tools

Screwdriver with parallel blade 2,5 • Adjust the throttle valves

Hexagon kay L-wrench 0,8

• Adjust the sensors

(included in the delivery of the

applicator)

2,5 • For standardized parts

(included in the delivery of the

applicator)

4 • Stamp adjustments

Stamp exchange

Flat-round nose pliers - straight

- angled

• Fitting/removing tubes

Open Spanner SW 8

• Changing the throttle valves

SW 13

• Setting the spring power on

the adapter bolt

SW20

• Changing the cylinder

Manometer ± 7 bar • Measuring air pressure

Table 3 Tools

6.4 Mounting and Demounting the Cover

To initialize the applicator

or perform adjustments it is required to remove the cover. Once content with the changes reattach

the cover.

Warning!

It is only permitted to use the applicator with a mounted cover (2).

Only in the case of servicing and maintenance may the cover be removed

1. Loosen the screw (3).

2. Lift off the cover upward (2).

3. Once the service or maintenance has been

completed lower the cover over the cylinders.

4. Guide cylinder (1) through the hole in the

cover (2).

5. Tightenthescrew(3)toxthecover(2)in

place.

Fig. 10 Cover

6 Installation

6.5 Mounting the Applicator

Attention!

 Disconnect the printer from the power supply before mounting/demounting the applicator!

 Ensure the printer is in a stable position

 Only when the applicator is securely mounted on the printer connect the compressed air.

1. Lower the applicator hinges (1) into the

printers hinges (2) effectively attaching the two

components.

2. Pull out the SUB-D 15 plug (6) a little from the

applicator to insert in into its counterpart on

the printer (7).

3. To secure the applicator lock it in place by

loosening the hinge screw (4), slide the hinge

lock (3) under the hinge and tighten the screw

again.

4. Pivot the applicator towards the printer making

sure that the cable of the plug (6) does not get

jammed between the components.

5. Usetheturn-wheelscrew(6)totoxtheappli-

cator to the printer.

6. Raise the transportation lock to ensure the

unhindered movement of the lift cylinder.

Fig. 11 Mounting the applicator to the printer

6.6 Releasing the Transportation Lock

Fig. 12 Stopper/transportation lock as transportation safety

Before the applicators are delivered, a stopper/transportation lock (2) is mounted on the rod (1). With this stopper (2)

the labelling position for the operation mode "blow on" can be adjusted. In transit the same stopper is in the transport

safety position, ensuring that the movement of the tamp is kept to a minimum. For longer transit times a stopper with

a cushion further reduces the impact energy (4).

Releasing the transportation lock

1. Loosen the screw (3) of the stopper (2).

2. Move the stopper (2) to the top end of the rod (1).

3. Tightenthescrew(3)toxthestopper(2)inplace.

18 18

6.7 Mounting the Blow Tube

1 2 3

Fig. 13 Mounting the blow tube

The blow tube (3) can be rotated around its axis. By this principle the direction of the compressed air can be

optimized.

1. Loosen the screw (1).

2. Insert the blow tube (3) as far as possible into the provided slot B (2).

3. Tighten the screw (1) to ensure the blow tube stays in place.  Adjustment of the blow tube and compressed air.

6.8 Connecting the Air Pressure

Attention!

Performance control and operational settings where tested with an air pressure of 4,5 bar.

The applicator operating range is between 4,0 and 6,0 bar.

Warning!

In case of connecting the printer to the compressed air the applicator is regard as "IN USE."

 Do not reach into the zone of the moving pad and keep long hair, loose clothes, and jewelry away.

Danger of injury by moving parts!

1 Ensure the setting of the stop valve (2) is

perpendiculartotheairowdirection.(As

illustrated).

2 Attachcompressedairtothetting(1).

3 Open the stop valve (2).

4 Switch on the printer via the power switch.

Tostabilizetheowofairitispossibletoattach

an air pressure regulation unit * (3).

This will need to be set up via the printer.

 Interface description of the printer

air pressure regulation unit * (4).

Fig. 14 Compressed air connection

Note!

If the pad is outside the start position when being switched on an error message will be shown on the

display of the printer and the operation will be interrupted.

If you push the pause button on the printer the applicator will move into the start position.

The Applicator is ready for use.

Note!

Mount and use the air pressure regulation unit only in the described position. Else the function of the

air-water separator can't be guaranteed.

6 Installation

6.9 Mounting the Suction Pads

Fig. 15 Mounting the suction pads

1. Loosen screws (3).

2. Slide the suction pads (4) over the provided pins (2) leaving approximately 1 mm between the clamps and the

pads to ensure mobility without friction.

Mount the suction pads so that the shorter pieces of foam are facing each other.

3. Alignment of the suction pads.

The surfaces of the suction pads that are facing the printer need to be level (5).

The bottom surfaces of the pads must be level and at an angle of 0° to each other.

4. Tighten the screws (3).

6.10 Preparing the Tamp Assembly for Adjustments

Fig. 16 Preparing the tamp assembly for adjustments

5. Pull off the tube (1) from the L-connector (2) on the horizontal cylinder.

6. Push the tamp in the direction of the printer.

7. Align the suction pads (3) to the edge of the printer  „7.1 Adjustments to the Tamp“ on page 20.

8. Connect the tube (1) to the L-connector (2).

6 Installation

20 20

7 Adjustments

7.1 Adjustments to the Tamp

For the perfect application of labels it is necessary that the tamp is placed precisely above the dispensed label.

Moving the tamp in x-, y- and z-direction

1 mm

Fig. 17 Moving the tamp assembly

Adjustment in X-direction (sideways adjustment)

1. Loosen screw (3).

2. Move cylinder assembly (5) with the pad at the bearing (4) so that the dispensed label is aligned centrally to the

pad. As reference use the provided graduation/ruler on the cross beam.

Orientation: Graduation (8) and Marking (7)

3. Tighten screw (3).

Adjustment in Y-direction (print direction)

1. Loosen screw (1).

2. Move cylinder assembly (4) with the tamp along the guiding rail that the distance from the edge of the pad (5) to

the edge of the dispensing plate (6) of the printer is approximately 1 mm. Orientation: Graduation (6) and Edge (5)

3. Tighten screws (1).

Adjustment in Z-direction (height adjustment)

1. Loosen screw (3).

2. Turn the setting screw (2) so that the bottom side of the pad is 1 mm over the top of the dispensing plate (6) of the

printer.

3. Tighten screw (3).

Page is loading ...

CAB Flag applicator 4712 User manual

Brand: CAB

Model: Flag applicator 4712

Type: User manual

This manual is also suitable for

HERMES Q / Hermes+ applicators

Download PDF

report

CAB Flag applicator 4712 User manual

This manual is also suitable for

CAB Flag applicator 4712 User manual

Related papers

Other documents