Made in Germany
Service Manual
3214
Swing Applicator
2 2
Family Type
Swing Applicator 3214L
Edition: 06/2017 - Part.-No. 9009524
Copyright
This documentation as well as translation hereof are property
of cab Produkttechnik GmbH & Co. KG.
The replication, conversion, duplication or divulgement of the
whole manual or parts of it for other intentions than its original
intended purpose demand the previous written authorization
by cab.
Editor
Regarding questions or comments please contact cab Produk-
ttechnik GmbH & Co. KG.
Topicality
Due to the constant further development of our products
discrepancies between documentation and product can occur.
Please check www.cab.de for the latest update.
Terms and conditions
Deliveries and performances are effected under the General
conditions of sale of cab.
Service Manual
for the following products
Germany
cab Produkttechnik
GmbH & Co KG
Postfach 1904
D-76007 Karlsruhe
Wilhelm-Schickard-Str. 14
D-76131 Karlsruhe
Telefon +49 721 6626-0
Telefax +49 721 6626-249
www.cab.de
France
cab technologies s.a.r.l.
F-67350 Niedermodern
Téléphone +33 388 722 501
www.cab.de/fr
USA
cab Technology Inc.
Tyngsboro MA, 01879
Phone +1 978 649 0293
www.cab.de/us
Asia
cab Technology Co., Ltd.
Junghe, Taipei, Taiwan
Phone +886 2 8227 3966
www.cab.de/tw
China
cab (Shanghai)Trading Co., Ltd.
Phone +86 21 6236-3161
www.cab.de/cn
Representatives in other countries on request
3
1 Introduction ............................................................................................................................................ 4
1.1 Instructions ...............................................................................................................................................4
1.2 Intended Use ............................................................................................................................................4
1.3 Safety Instructions ....................................................................................................................................4
1.4 Safety Markings .......................................................................................................................................5
1.5 Environment .............................................................................................................................................5
2 Product Description ...............................................................................................................................6
2.1 Important Features ...................................................................................................................................6
2.2 Technical Data ..........................................................................................................................................6
2.3 Overview .................................................................................................................................................. 7
2.4 Contents of Delivery .................................................................................................................................9
3 Operation .............................................................................................................................................. 10
3.1 Standard Operation ................................................................................................................................10
3.2 Cleaning .................................................................................................................................................10
4 Error Messages .................................................................................................................................... 12
4.1 Error Messages of the Printer ................................................................................................................ 12
4.2 Error Messages of the Applicator ...........................................................................................................12
5 Licences ................................................................................................................................................13
5.1 Declaration of Incorporation ...................................................................................................................13
5.2 EU Declaration of Conformity .................................................................................................................14
6 Installation ............................................................................................................................................ 15
6.1 Factory Defaults .....................................................................................................................................15
6.2 Tools .......................................................................................................................................................16
6.3 Mounting the applicator ..........................................................................................................................16
6.4 Transport lock.........................................................................................................................................17
6.5 Mounting the Pad ...................................................................................................................................18
6.6 Mounting the Blow Tube .........................................................................................................................18
6.7 Connecting the Compressed Air ............................................................................................................19
7 Adjustments .........................................................................................................................................20
7.1 Pad Adjustments .................................................................................................................................... 20
7.2 Adjusting the Swing Area of the Pad ......................................................................................................21
7.3 Stopper for Operation Mode "Blow on" .................................................................................................. 22
7.4 Adjusting the Sensors of the Swing Drive ..............................................................................................23
7.5 Adjusting the Speed of the Swing Drive .................................................................................................23
7.6 Sensors on Cylinder Z ............................................................................................................................24
7.7 Lift Speed of Cylinder Z ..........................................................................................................................25
7.8 Adjusting the pressure reduction valve .................................................................................................. 25
7.9 Vacuum Adjustments ..............................................................................................................................26
7.10 Blow Tube (Support Air) Adjustments .....................................................................................................27
8 Conguration
........................................................................................................................................29
8.1 Method for Changing the Printer Setup ..................................................................................................29
8.2 Quick Mode for Setting the Delay Times ................................................................................................29
8.3 CongurationParametersoftheApplicator ...........................................................................................30
8.4 Setting the Peel Position ........................................................................................................................31
8.5 Activation of Peel-off Mode .................................................................................................................... 31
9 Operation .............................................................................................................................................. 32
9.1 Test Mode without Print Job ...................................................................................................................32
9.2 Test Mode with Print Job ........................................................................................................................32
10 Spare Parts ........................................................................................................................................... 33
10.1 Retainer Assembly ................................................................................................................................. 33
10.2 Pneumatics Retainer Assembly .............................................................................................................34
10.3 Electronics Retainer Assembly ...............................................................................................................35
10.4 Swing Drive / Cylinder Assembly ...........................................................................................................36
10.5 Pad Assembly ........................................................................................................................................37
11 Drawings ...............................................................................................................................................38
11.1 Block Diagram Type 3214 ......................................................................................................................38
11.2 Pneumatic Drawing Type 3214 ............................................................................................................. 39
12 Index ......................................................................................................................................................40
Table of Contents
4 4
1 Introduction
1.1 Instructions
Important information and instructions in this documentation are designated as follows:
Danger!
Draws attention to an exceptionally great, imminent danger to your health or life due to hazardous
voltages.
!
Danger!
Draws attention to a danger with high risk which, if not avoided, may result in death or serious injury.
!
Warning!
Draws attention to a danger with medium risk which, if not avoided, may result in death or serious injury.
!
Caution!
Draws attention to a danger with low risk which, if not avoided, may result in minor or moderate injury.
!
Attention!
Draws attention to potential risks of property damage or loss of quality.
i
Note!
Advice to make work routine easier or on important steps to be carried out.
Environment!
Gives you tips on protecting the environment.
Handling instruction.
Reference to section, position, illustration number or document.
Option(accessories,peripheralequipment,specialttings).
Time
Information in the display.
1.2 Intended Use
• The device is manufactured in accordance with the current technological status and the recognized safety rules.
However, danger to life and limb of the user or third parties and/or damage to the device and other tangible assets
can arise during use.
• The device may only be used for its intended purpose and if it is in perfect working order, and it must be used with
regard to safety and dangers as stated in the operating manual.
• The device applicator mounted on a cab printer of the Hermes+ series is intended exclusively for applying suitable
materials that have been approved by the manufacturer. Any other use or use going beyond this shall be regarded
as improper use. The manufacturer/supplier shall not be liable for damage resulting from unauthorized use; the
user shall bear the risk alone.
• Usage for the intended purpose also includes complying with the operating manual, including the manufacturer‘s
maintenancerecommendationsandspecications.
i
Note!
The complete and current version of the documentation can be found in the Internet.
1.3 Safety Instructions
!
Attention!
Initiation,adjustmentsandchangingofpartsaretobeperformedbyqualiedservicepersonnelonly.
!
Warning!
This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
5
1 Introduction
• Before mounting the delivered components disconnect the printer from the power supply and close the shutoff
valve of the applicator.
• Only connect the device to other devices which have a protective low voltage.
• Switch off all affected devices (computer, printer, accessories) before connecting or disconnecting.
• In operation, moving parts are easily accessible.
This applies especially for the zone, where the pad is moved between the starting and the labelling position.
During operation do not reach into that zone and keep long hair, loose clothes, and jewelry distant. Before any
manipulations in those areas, close the shutoff valve.
• The device may only be used in a dry environment, do not expose it to moisture (sprays of water, mists, etc.).
• Do not use the device in an explosive atmosphere.
• Do not use the device close to high-voltage power lines.
• Perform only those actions described in this operating manual.
Work going beyond this may only be performed by trained personnel or service technicians.
• Unauthorized interference with electronic modules or their software can cause malfunctions.
• Otherunauthorizedworkonormodicationstothedevicecanalsoendangeroperationalsafety.
• Alwayshaveserviceworkdoneinaqualiedworkshop,wherethepersonnelhavethetechnicalknowledgeand
tools required to do the necessary work.
• There are various warning stickers on the device. They draw your attention to dangers. Warning stickers must
therefore not be removed, as then you and other people cannot be aware of dangers and may be injured.
1.4 Safety Markings
3
1
2
1: Warning potential injury by
moving parts!
2:
Cylinder is under pressure, also
after it is switched off!
3:
Danger of crushing hands and/or
ngersbythemovingpad!
!
Attention!
Never remove or cover safety markings!
Replace it in case of damage!
Fig. 1 Safety marking
1.5 Environment
Obsolete devices contain valuable recyclable materials that should be sent for recycling.
Send to suitable collection points, separately from residual waste.
The modular construction of the applicator enables it to be easily disassembled into its component parts.
Send the parts for recycling.
6 6
2 Product Description
2.1 Important Features
• The supporting air and the vacuum as well as the speed of the cylinder are adjustable. That way the applicator
can be adapted to different label materials and sizes.
• To avoid contamination within the vacuum channels they are cleaned by air pressure impulse at the end of each
application.
• For operation in a system the I/O interface of the printer can be used.
2.2 Technical Data
Label transfer method Tamp pad Tamp pad
with foam
Tamp pad
with label stop
Blow pad
3214 L/R 11 F 3214 L/R 12 F 3214 L/R 61 F 3214 L/R 2100
Label width in mm for Hermes
+
4 4 -58 10 - 58 10 - 58 10 - 58
for Hermes
+
6 10 - 114 10 - 114 10 - 114 10 - 80
Label height in mm 5 - 80 10 - 80 5 - 80 10 - 80
Compressed air pressure 0.45 MPa (4.5 bar)
Sound pressure level under 74 dB(A)
Product during
labeling
xed
¢ ¢ ¢ ¢
in motion - - -
¢
Labeling onto the
product
sideways
¢ ¢ ¢ ¢
Product height x
¢ ¢ ¢ ¢
Distance of product to
dispensing edge in mm
250 - 280 250 - 280 250 - 280 250 - 280
Horizontal short stroke cylinder in mm 5 - 30 5 - 30 5 - 30 5 - 30
Swing angle 45° - 95° 45° - 95° 45° - 95° 45° - 95°
Immersion depth pad F
2)
up to mm 30 30 30 -
Cycle time about frequency/min.
1)
25 25 25 25
1)
Determined at 100 mm stroke below device / smallest label height / print speed 100 mm/s .
2)
Immersion depth at applicator >25 mm, the cover of the Hermes
+
mustbemodied.
Table 1 Technical Data
7
2.3 Overview
support air
vacuum
17
18
12
11
7
6
5
4
2
8
10
3
1
9
13
14
15
16
Fig. 2 Device overview - front view
1 Eccentric o adjust the angle between applicator and
printer
2 Knurled screw for attaching the applicator to the
printer
3 Setting screw to adjust the angle between applicator
and printer
4 Compressed air connector
5 Shutoff valve
6 Throttle valve cylinder - move in Z-direction
7 Throttle valve cylinder - move out Z-direction
8 Setting screw for vertical adjustment cylinder
assembly
9 Swing drive
10 Cylinder - Z-direction
11 Sensor labeling position
12 Blow tube for supporting air
13 Throttle valve swing drive - swing in
14 Throttle valve swing drive - swing in
15 Throttle valve swing drive - swing out
16 Setting screw to adjust the angle of the swing area
17 Support air throttle valve
18 Vacuum throttle valve
Front view
Throttle valves vacuum/support air
y
x
z
2 Product Description
Swing drive
y
x
z
8 8
22
21
20
23
Rear view
19
19
24
25
26
27
28
30
29
Fig. 3 Device overview - rear view Fig. 4 Device overview - control system
19 Hinges
20 Locking for hinges
21 Interface to the printer
22ScrewstoxtheZ-direction
23 Pad (customized)
24 Valve swing drive
25 Valve Cylinder Z/Y-direction
26 Valve Blow air
27 Valve Vacuum and Support air
28 PCB Applicator Control
2 Product Description
yx
z
Valves and control system
y
x
z
9
2 Product Description
2.4 Contents of Delivery
2
4
3
1
1 Applicator
2 Screws (part of the pad)
3 Blow tube (as ordered)
4 Pad (as ordered)
5 Documentation
Fig. 5 Contents of delivery
i
Note!
Please keep the original packaging in case the applicator needs to be returned.
!
Attention!
The device and printing materials will be damaged by moisture and wetness.
Only set up the label printer with applicator in dry locations protected from moisture and splashes.
10 10
3 Operation
y
x
z
3.1 Standard Operation
Check all external connections.
Load the material. Ensure that the locking system is closed "Operator's Manual" of the printer.
Open the shutoff valve.
!
Attention!
Ensure that the pad is not covered by a label when switching on the printer-applicator system, or the
vacuum sensor may be calibrated incorrectly.
Switch on the printer.
i
Note!
In case the pad is outside the starting position at the moment of switching on the air pressure the procedure
will be interrupted and an error message will be displayed.
By pushing the pause button on the printer the error is acknowledged and the pad will move back to its
starting position.
The Applicator is ready for work.
Press the feed key of the printer.
A synchronization feed is initiated and the processed labels need to be removed manually. After a few seconds
the printer carries out a short backfeed to position the front edge of the next label at the start of the printing line.
i
Note!
This synchronizing also has to be carried out when the print job has been interrupted with the cancel key.
Synchronizing is not necessary when the print head was not lifted between print jobs. This also applies if
the printer was powered off between print jobs.
Start a print job.
Start the labelling process via PLC interface.
Error messages that occur during the labelling process are shown in the display of the printer 4 Error Messages.
3.2 Cleaning
!
Attention!
Never use solvent and abrasive.
1
Clean the outside surfaces with multi purpose cleaner.
Remove dust particles and leftover label pieces with a soft
brush and/or vacuum cleaner.
The slide foil (1) requires regular cleaning as the most dirt
is deposited here.
Fig. 6 Cleaning pad with slide foil
11
1
1
2
2
6
7
3
4
5
3 Operation
Fig. 7 Mounting applicator to printer
!
Attention!
Initiation,adjustmentsandchangingofpartsistobeperformedbyqualiedservicepersonalonly.
Initiation/Service Manual Applicators
!
Attention!
Disconnect the printer from the power supply before mounting the applicator!
Ensure that the printer is positioned stably and securely.
Connect the compressed air only after mounting the applicator to the printer!
To clean the applicator and printer it is sometimes necessary to turn away or even dismount the applicator from the
printer.
Take care not to adjust the setting screws, throttle valves or other alignment elements. This will enable use of the
applicator directly after cleaning.
Pivot away/dismount the applicator
1. To turn away the applicator loosen thumbscrew (5) and swing the applicator aside.
2. Disconnect SUB-D 15 male connector (6) from the female connector (7) of the printer.
3. Loosen screw (4) and slide the locking plate (3) off.
4. Lift the applicator off the hinges.
Mount the applicator
1. Mount the applicator to the printer via the female hinges (1) to the printer via the male hinges (2).
2. Connect SUB-D 15 male connector (6) to the female connector (7) of the printer.
3. To secure the applicator from slipping out of hinges loosen screw (4) and move the locking plate (3) under the
hinges and tighten screw (4).
4. Swing the applicator to the printer and tighten the thumbscrew (5).
12 12
4 Error Messages
4.1 Error Messages of the Printer
For detailed information about printer errors (e.g. 'Paper out', 'Ribbon out', etc.) Operator's manual of the printer
Error treatment:
Clear the error results
Press the feed key to synchronize the label feed, remove the peeled labels manually
Press the pause key to quit the error state.
After error correction, the printing of the label causing the error will be repeated.
4.2 Error Messages of the Applicator
The following table contains an overview of error messages and their possible causes. It also suggests methods to
resolve the problem:
Error Message Possible Cause
Air pressure ins.
Compressed air is switched off
Pressure to low < 4 bar
Pressure to high > 6 bar
Label not depos.
Label has not been placed onto the product; after the pad has moved back the label is
still on the pad.
Lower position
Pad is not in start position when the printer was switched on.
Pad has not reached the labelling position within 2s after the movement of the pad was
started
Padhasundenedleavingthestartposition.
Process Error
Process of labeling was interrupted via the I/O interface of the printer with the XSTP
signal.
Re. sensor blk.
There has been no change in state at the upper sensor at the cylinder between the start
of the labelling process and the signal from the labelling position sensor.
Vac. plate empty
Label has not been picked up properly by the pad; or label fell off the pad before it could
be placed onto the product.
Upper position
Pad has not reached the starting position within 2s after the pad has left the labelling
position; or pad has left the starting position unauthorized
Table 2 Error messages of the applicator
Error treatment:
Clear the error results
Press the pause key to quit the error state.
i
Note!
In fault check adjustments and settings with help of the Service Manual.
!
Warning!
The pad will immediately be moved in the starting position!
Dangerofcrushinghandsandngersbythemovingpad!
Do not reach into the zone of the moving pad and keep long hair, loose clothes, and jewelry away.
After error correction, the print of the label causing the error cannot be repeated without re-start of the print job.
Except at the error " Vac. plate empty" . In this case, the latest label will print again after quit the error with the
pause key and then press the Enter button
.
Intheapplicationmode"Apply/Print"sendthesignal"Printrstlabel"orpressthebutton to send a printed
label to the pad.
13
5 Licences
5.1 Declaration of Incorporation
cab Produkttechnik
GmbH & Co KG
Wilhelm-Schickard-Str. 14
D-76131 Karlsruhe
Deutschland
Declaration of Incorporation
We declare herewith that the following „partly completed machinery“ as a result of design, construction and the version
put in circulation complies with the essential requirements of the Directive 2006/42/EC on machinery:
Annex I, Article 1.1.2, 1.1.3, 1.1.5, 1.1.6, 1.2.1, 1.3.2, 1.5.2, 1.5.8, 1.6.3, 1.7
In the event of any alteration which has not been approved by us being made to any device as designated below, this
statement shall thereby be made invalid.
Device: Swing Applicator
Type: 3214
Applied EU Regulations and Norms:
Directive 2006/42/EC on machinery
• EN ISO 12100:2010
• EN ISO 13849-1:2008
• EN 60950-1:2006
+A11:2009+A12:2011+A1:2010+A2:2013
Personauthorisedtocompilethetechnicalle: Erwin Fascher
Am Unterwege 18/20
99610 Sömmerda
Signed for, and on behalf of the Manufacturer:
cab Produkttechnik Sömmerda
Gesellschaft für Computer-
und Automationsbausteine mbH
99610 Sömmerda
Sömmerda, 19.06.2017
Erwin Fascher
Managing Director
Theproductmustnotbeputintoserviceuntilthenalmachineryintowhichitistobeincorporatedhasbeendeclaredin
conformity with the provisions of the Directive on machinery
The documents according annex VII part B from the incomplete machinery are created and will commit to state agencies
on request in electronic kinds.
14 14
5 Licences
5.2 EU Declaration of Conformity
cab Produkttechnik
GmbH & Co KG
Wilhelm-Schickard-Str. 14
D-76131 Karlsruhe
Deutschland
EU Declaration of Conformity
We declare herewith that as a result of the manner in which the device designated below was designed, the type of
construction and the devices which, as a result have been brought on to the general market comply with the relevant
fundamental regulations of the EU Rules for Safety and Health. In the event of any alteration which has not been
approved by us being made to any device as designated below, this statement shall thereby be made invalid.
Device: Swing Applicator
Type: 3214
Applied EU Regulations and Norms: Applied Norms:
Directive 2014/30/EU relating to electromagnetic compatibility
• EN 55032:2012
• EN 55024:2010
• EN 61000-6-2:2005
Directive 2011/65/EU on the restriction of the use of certain
hazardous substances in electrical and electronic equipment
• EN 50581:2012
Signed for, and on behalf of the Manufacturer:
cab Produkttechnik Sömmerda
Gesellschaft für Computer-
und Automationsbausteine mbH
99610 Sömmerda
Sömmerda, 19.06.2017
Erwin Fascher
Managing Director
15
6 Installation
6.1 Factory Defaults
i
Note!
Theapplicatorisbythefactoryadjustedafterdefaultvaluesinastandardconguration.Attitudesafter
thesevaluesguaranteeasmoothoperationwithsameconguration.
i
Note!
Incaseofacustomersetupwillbetheadjustmentswiththecustomizedconguration.
It's possible that the values are different to the standard values.
Then the values in the setup protocol are valid.
The standard settings are:
- Connecting on a cab Hermes+ printer, vertical
- Used Pad: cab part No.: 5963881 54x36
cab part No.: 5963878 54x36
- Used material for ex-factory settings: cab part No.: 5556472 54x35.5
- Pressure value of the compressed air 0.45 MPa (4.5 bar)
16 16
6.2 Tools
Screwdriver with parallel blade 2.5 To adjust the throttle valves and
product sensor
Hexagon key L-wrench 0.8
To adjust the sensors
(in contents of delivery)
2.5 For matched norm parts
(in contents of delivery)
4 Pad adjustments
Changing pad
Flat-round nose
straight
To mount/dismount tubes
angled
Open spanner SW 8 To change the throttle valves
SW 13 Setting the spring power on the
adapter bolt
SW20 Changing the cylinder
Manometer ± 7 bar
Air pressure control
Fig. 8 Tools
6.3 Mounting the applicator
!
Attention!
Disconnect the printer from the power supply before mounting the applicator!
Ensure a stable standing of the printer!
Connect the compressed air only after mounting the applicator to the printer!
1
1
2
2
6
7
3
4
5
1. Hang the applicator to the printer via the
female hinges (1) and the male hinges (2).
2. Connect SUB-D 15 male connector (6) to its
female counterpart (7).
3. To secure the applicator from slipping out of
hinges loosen screw (4) and move locking
plate (3) under the hinges. Tighten screw (4).
4. Swing the applicator to the printer and ensure
that the cable is not caught between the two.
5. Tighten the thumbscrew (5).
6. Raise the stopper from the transport position
to enable movement of cylinder Z.
Fig. 9 Mounting applicator to printer
6 Installation
17
6.4 Transport lock
The transportation lock of the applicator prevents movement of the applicators parts to avoid damage and ensure
safe transportation for the applicator and the persons executing it.
!
Warning!
Ensure that the printer's power supply is disconnected and the compressed air supply is closed before
dismounting the applicator.
!
Warning!
Risk of injury and damage in the case of incorrect use and/or operation of the devices.
The applicator may only be used with a Hermes+ series printer.
2
3
2
1
4
Fig. 10 Transport lock
Remove the transport lock
1. Loosen screws (2) of the transport lock (3) .
2. Remove the transport lock (3).
!
Attention!
Mount the transportation lock for every transport.
Keep the transport lock and the screws.
Mounting the transport lock
1. Turn the swing arm (4) so that the pad holder is in the cut-out of the transport lock (3) .
This is an almost vertical position.
2. Place the transport lock (3) so that the holes in the transport lock (3) are over the holes (1) on both sides of the
swing cylinder socket.
3. Tighten screws (2).
6 Installation
18 18
6 Installation
6.5 Mounting the Pad
2
7
3
4
8
6
5
1
4
Fig. 11 Mounting the pad
1. Slide the pad with the holes (4) onto the pad holder (1) via the pins (3).
2. Fasten the pad to the pad holder (1) with the screw (2).
3. Insertthevacuumtube(5)andthesupportairtube(6)intotheappropriatepush-in-ttings(7,8)ofthepad.
!
Attention!
To avoid possible collisions of the pad with other parts of the printer-applicator system, please roughly
align the pad in all directions ( Adjustments) before connecting the applicator to the compressed air
supply!
6.6 Mounting the Blow Tube
1
2 3
Fig. 12 Mounting the blow tube
The blow tube (3) for the supporting air can be rotated around its axis. This allows the direction of the supporting air
to be optimized.
1. Loosen screw (1).
2. Put the blow tube (3) into the hole A (2) as far as possible.
3. Tighten screw (1). Adjust the blow tube (Support air)
19
6 Installation
6.7 Connecting the Compressed Air
!
Attention!
Adjustments and function control where undertaken with a compressed air value of 4.5 bar.
The applicator operating range is between 4.0 and 6.0 bar.
!
Warning!
In case of connecting printer and compressed air the applicator is regard as in operation.
Do not reach into the zone of the moving pad and keep long hair, loose clothes, and jewelry away.
Danger of injury and damage by the moving rods!
2
1
3
4
1 Check the vertical position of the stop valve
(2). (The stop valve is closed in the picture.)
2 Attachthecompressedairviathetting(1).
3 Open the stop valve (2). (The lever indicates
thedirectionofairow.)
4 Switch on the printer.
It's possible to use an air pressure regulation unit
with included magnetic valve. *(3)
Controlling via the printer.
Interface description of the printer air pressure
regulation unit *(4)
Fig. 13 Compressed air connection
i
Note!
In case the pad is outside the starting position at the moment of switching on the air pressure the procedure
will be interrupted and an error message will be displayed.
By pushing the pause button on the printer the error is acknowledged and the pad will move back to its
starting position.
The Applicator is ready for work.
i
Note!
Only mount and use the air pressure regulation unit in the illustrated position or the functionality of the
air-water separator cannot be guaranteed.
20 20
7 Adjustments
7.1 Pad Adjustments
For optimal results it is necessary to place the pad precisely over the dispensed labels for the take over procedure.
Moving the pad in X-, Y- and Z-direction
10
1 mm
9
3
2
4
1
5
6
8
7
1 mm
y
x
z
x
y
z
Fig. 14 Moving the pad assembly
Adjustment in X-direction (sideways adjustment)
1. Loosen screw (3).
2. Move the cylinder assembly group (5) including pad along the cross beam until the pad is over the middle of the
label intended for application. For better orientation there is a graduation mark (7,8) depicted on the assembly
group.
3. Tighten screw (3).
Adjustment in Y-direction (print direction)
1. Loosen screw (1).
2. Move cylinder assembly (4) including pad along the guide rail so that the distance between the edge of the pad
(5) and the edge of the dispense plate (6) of the printer is approximately 1 mm. Graduation (5,6) can be used for
orientation.
3. Tighten screws (1).
Adjustment in Z-direction (height adjustment)
1. Loosen screw (3).
2. Turn setting screw (2) so that the bottom of the pad is 1 mm over the top edge of the dispense plate (6).
3. Tighten screw (3).
Adjusting the Parallelism between Pad and Dispense Edge
The edge of the pad must be parallel to the dispense edge of the printer.
9 10
14
13
11 12
Fig. 15 Adjusting the pad to the dispense edge
1. Loosen knurled screw (13) and screw (12).
2. Push the applicator against the printer and adjust the angle between applicator pad edge (9) and printer
dispensing plate (10) via the setting screw (14) and the eccentric (11).
3. Tightenscrew(12)andrextheapplicatorviaknurledscrew(13)oftheprinter.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
CAB HERMES Q / Hermes+ applicators User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
CAB Swing applicator 3214 User manual
-
CAB HERMES Q / Hermes+ applicators Operating instructions
-
-
CAB Flag applicator 4714 Operating instructions
-
-
CAB A+ series applicators Operating instructions
-
-
-
-
Other documents
-
Brady PAM 3600 Quick Operator's Manual
-
Carl Valentin Applicator APL 100 User manual
-
-
Rupes HB 625 Operating And Maintenance Instructions Manual
-
Carl Valentin Compa V + Pneumatic Applicator C User manual
-
-
-
ROOMS TO GO 90151019 Assembly Instructions
-
Zimmer ZLipo Med Instructions For Use Manual
-
Universal L60 User manual
