2. Vehicles & accessories
  3. Motor vehicle accessories & components
  4. Motorcycle Accessories
  5. Kichler Lighting
  6. 84095MBK

Kichler Lighting 84095MBK User manual

  • Hello! I am an AI chatbot trained to assist you with the Kichler Lighting 84095MBK User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
IS-84095-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Pass xture wires from coupling on top of main body[I] through desired number of
stems[A] and short threaded tubes[B]. Screw stems together using supplied short
threaded tubes.
NOTE: Thread locking compound must be applied to all stem threads as noted with
(4) symbol to prevent accidental rotaon of xture during cleaning, relamping, etc.
2) Screw connected stems into coupling on top of main body using a short threaded
tube.
3) Pass xture wires from last stem through swivel[C]. Swivel should be installed with
the longer end hanging down towards the mounng stems.
4) Screw longer end of swivel into end of last stem.
NOTE: Fixture wire should not be cut shorter than 20 inches from above the
canopy[D].
5) Aach mounng plate[G] to outlet box[H] using the plate mounng screws[E].
Mounng plate can be adjusted to suit posion of xture.
6) Wrap supply ground wire (BARE COPPER OR GREEN) around ground screw aached
to mounng plate and ghten screw. Be sure to leave extra wire beyond ground
screw to make connecon with ground wire from xture (no less than 2”).
7) Connect driver neutral input wire (WHITE) to supply neutral wire (WHITE) using P4
(YELLOW) wire nut.
8) Connect driver live input wire (BLACK) to supply hot wire (BLACK) using P4 (YELLOW)
wire nut.
9) Using a P4 (YELLOW) wire nut, connect xture ground wire (BARE COPPER) to supply
ground wire (aached to the mounng plate ground screw).
10) Connect xture neutral wire (BLUE or BLACK) to driver neutral output wire (BLUE or
BLACK) using P3 (ORANGE) wire nut.
11) Connect xture live wire (RED) to driver live output wire (RED) using P3 (ORANGE)
wire nut.
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before starng and
during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical Code
(NEC) and all local code specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
CLEANING:
• Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage
the nish.
Installaon Instrucons
[A] Stems
[B] Short Threaded Tubes
[C] Swivel
[D] Canopy
[E] Plate Mounting
Screws
[F] Mounting Screws
[G] Mounting Plate
[H] Outlet Box
[I] Main Body
[J] Globe
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will
not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Informaon:
For warranty informaon please visit: kichler.com/warranty
12) Raise xture to ceiling, carefully passing canopy[D] over mounng plate.
NOTE: Be certain wires do not get pinched between mounng plate and canopy, or
canopy and ceiling.
13) Align three (3) holes on side of canopy to three (3) holes on mounng plate.
14) Secure canopy to mounng plate using three (3) mounng screws[F].
15) Raise globe[J] up into LED housing and rotate to lock globe into place over LED.
WIRING DIAGRAM
LIVE (HOT) WIRE (+DC)
FROM FIXTURE (RED)
GROUND WIRE FROM FIXTURE
(BARE COPPER)
NEUTRAL WIRE (-DC) FROM FIXTURE
(BLUE OR BLACK)
LIVE (HOT) OUTPUT WIRE (+DC)
FROM DRIVER (RED)
NEUTRAL OUTPUT WIRE (-DC)
FROM DRIVER (BLUE OR BLACK)
SUPPLY GROUND WIRE
(BARE COPPER OR GREEN)
NEUTRAL INPUT WIRE (-AC)
TO DRIVER (WHITE)
LIVE (HOT) INPUT WIRE (+AC)
TO DRIVER (BLACK)
SUPPLY GROUND WIRE
(BARE COPPER OR GREEN)
SUPPLY NEUTRAL WIRE
(WHITE)
CANOPY
DRIVER (ATTACHED
TO CANOPY)
OUTLET BOX
P4 WIRE NUT
(YELLOW)
P3 WIRE NUT
(ORANGE)
P4 WIRE NUT
(YELLOW)
P3 WIRE NUT
(ORANGE)
P4 WIRE NUT
(YELLOW)
SUPPLY HOT WIRE
(BLACK)
►
►
►
I
B
A
A
C
D
F
E
G
H
J
Page is loading ...
Page is loading ...
/