FSR WB-X1NK-GNG-B Installation guide

FSR
Brand
FSR
Model
WB-X1NK-GNG-B
Type
Installation guide

This manual is also suitable for

FSR 244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207
43017 LIT1404
SEPARATOR
UPPER END OF
CHASSIS UPON
INSTALLATION
ASSEMBLED 4G
MOUNTING PLATE
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
UPPER GANG-UNIT END
LOWER GANG-UNIT END
MAKE ELECTRICAL CONNECTIONS AS REQUIRED.
6.
5.
4.
3.
2.
STEPS:
7.
REINSTALL 4G MOUNTING PLATE AS SHOWN IN
FIGURE 1. USE SEPARATOR AS REQUIRED.
REINSTALL GANG-UNIT ENDS AS SHOWN IN
FIGURE 2.
ROUTE CONDUITS TO CHASSIS, AND PULL
WIRES AS REQUIRED.
INSTALL CHASSIS INTO WALL PER INSTRUCTIONS
AT THE END OF THIS DOCUMENT.
REMOVE UPPER/LOWER GANG-UNIT END FROM
CHASSIS AS SHOWN IN FIGURE 2, SETTING
GANG-UNIT ENDS AND SCREWS ASIDE.
1. REMOVE ASSEMBLED 4G MOUNTING PLATE
FROM CHASSIS AS SHOWN IN FIGURE 1,
SETTING PLATE AND SCREWS ASIDE.
WB-X1-GNG
WB-X1-GNG / WB-X1-IPS / WB-X1-PLT / WB-X1-XLR INSTALLATION INSTRUCTIONS
FIGURE 1
FIGURE 2
2.
INSTALL CHASSIS INTO WALL PER
INSTRUCTIONS AT THE END OF THIS
DOCUMENT.
MAKE ELECTRICAL CONNECTIONS AS REQUIRED.
INSTALL FRAME ASSEMBLY AS SHOWN IN
FIGURE 4.
3.
STEPS:
1.
5. INSTALL IPS WALLBOX BUCKETS AS SHOWN IN
FIGURE 5.
6.
4.
ASSEMBLE FRAME ASSEMBLY AS SHOWN IN
FIGURE 3.
ROUTE CONDUITS TO CHASSIS, AND PULL
WIRES AS REQUIRED.
(4) #8-32x1/4" FLAT HEAD SCREW
(LOCTITE RECOMMENDED)
NOTE SLOT
IPS UPPER INTERIOR
SUPPORT BRACKET
IPS LOWER INTERIOR
SUPPORT BRACKET
(2) IPS BUCKET
MOUNTING BRACKET
NOTE SLOT LOCATION,
WHICH DESIGNATES
UPPER END OF CHASSIS
UPON INSTALLATION
(6) #8-32x1/4" FLAT
HEAD SCREW
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
FRAME
ASSEMBLY
(8) #8-32x1/4" FLAT
HEAD SCREW
(2) IPS WALLBOX
BUCKET
UPPER END OF
CHASSIS UPON
INSTALLATION
WB-X1-IPS
NOTE: ASSEMBLE
FRAME AS SHOWN ON
A FLAT SURFACE
FIGURE 3
FIGURE 4 FIGURE 5
HEIGHT ADJUSTMENT HOLE
(ENSURE BOTH BRACKET ASSEMBLIES
ARE USING THE SAME HOLES)
BLANK PLATE MOUNTING BRACKET
(2) #8-32x3/8" PAN
HEAD SCREW
MOUNTING
BRACKET
SUPPORT
(6) #8-32x1/4" FLAT
HEAD SCREW
BRACKET ASSEMBLY
BRACKET
ASSEMBLY
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
(4) #8-32x3/8" PAN
HEAD SCREW
BLANK PLATE
INSTALL BRACKET ASSEMBLIES AS SHOWN IN FIGURE 7.
MAKE ELECTRICAL CONNECTIONS AS REQUIRED.
INSTALL CHASSIS INTO WALL PER INSTRUCTIONS AT THE END
OF THIS DOCUMENT.
6.
3.
ROUTE CONDUITS TO CHASSIS, AND PULL WIRES AS REQUIRED.
STEPS:
5. MODIFY BLANK PLATE AS NECESSARY TO MOUNT DESIRED
COMPONENTS. INSTALL THIS PLATE AS SHOWN IN FIGURE 8.
ASSEMBLE BRACKET ASSEMBLY AS SHOWN IN FIGURE 6.
4.
2.
1.
WB-X1-PLT
FIGURE 6
FIGURE 7 FIGURE 8
COMPONENT AREA
NOTE STRAIGHT SURFACE
(4) #8-32x1/4" FLAT HEAD SCREW
(LOCTITE RECOMMENDED)
XLR UPPER INTERIOR
SUPPORT BRACKET
XLR LOWER INTERIOR
SUPPORT BRACKET
(2) XLR BUCKET
MOUNTING
BRACKET
NOTE STRAIGHT SURFACE,
WHICH DESIGNATES
UPPER END OF CHASSIS
UPON INSTALLATION
(6) #8-32x1/4" FLAT
HEAD SCREW
FRAME ASSEMBLY
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
6.
INSTALL CHASSIS INTO WALL PER INSTRUCTIONS
AT THE END OF THIS DOCUMENT.
ROUTE CONDUITS TO CHASSIS, AND
PULL WIRES AS REQUIRED.
ASSEMBLE FRAME ASSEMBLY AS SHOWN
IN FIGURE 9.
INSTALL FRAME ASSEMBLY AS SHOWN IN
FIGURE 10.
INSTALL XLR WALLBOX BUCKETS AS SHOWN IN
FIGURE 11.
STEPS:
1.
2.
3.
4.
5.
MAKE ELECTRICAL CONNECTIONS AS REQUIRED.
(12) #8-32x1/4" FLAT
HEAD SCREW
UPPER END OF
CHASSIS UPON
INSTALLATION
(3) XLR WALLBOX
BUCKET
NOTE: ASSEMBLE
FRAME AS SHOWN ON
A FLAT SURFACE
FIGURE 10 FIGURE 11
FIGURE 9
WB-X1-XLR
5.
3.
1.
MOUNT CHASSIS ASSEMBLY TO WALL AS
SHOWN IN FIGURE 14.
ENSURE AT LEAST 3" OF BLOCKING MATERIAL
BEYOND BOTH UPPER AND LOWER EDGES OF
CUT-OUT.
CUT A 9-1/2" x 12-1/2" OPENING IN WALL
CENTERED BETWEEN THE STUDS.
WB-X1 INSTALLATION (OLD-WORK)
4.
2.
STEPS:
INSTALL OLD-WORK MOUNTING BRACKET TO
CHASSIS ASSEMBLY AS SHOWN IN FIGURE 13.
INSTALL SCREW/CLAMP BLOCK ALONG EDGE OF
CUT-OUT AS SHOWN IN FIGURE 12 - SEE STEP 3.
1" CUSTOMER-SUPPLIED
BLOCKING - 5/4 WOOD
MATERIAL RECOMMENDED
2 x 4 STUDS
16" ON CENTER
SCREW/CLAMP BLOCK
(8) CUSTOMER-
SUPPLIED
#8 WOOD SCREW
1/2" OR 5/8" DRYWALL
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
(2) OLD-WORK
MOUNTING
BRACKET
(8) #8-32 SCREW
(SUPPLIED)
FIGURE 12
FIGURE 13 FIGURE 14
(8) CUSTOMER-SUPPLIED
#8 WOOD SCREW
(AFTER CHASSIS IS IN
POSITION IN WALL)
2.
INSTALL (2) MOUNTING BRACKET TO CHASSIS
ASSEMBLY AS SHOWN IN FIGURE 15.
INSTALL BOX ASSEMBLY ONTO STUDS
AS SHOWN IN FIGURE 16.
STEPS:
WB-X1 INSTALLATION (NEW-WORK)
1.
FIGURE 16
FIGURE 15
(2) NEW-WORK
MOUNTING
BRACKET
(8) #8-32 SCREW
(SUPPLIED)
CHASSIS ASSEMBLY
(AVAILABLE WITHOUT KO'S)
CUSTOMER-SUPPLIED
#8 WOOD SCREWS,
NAILS OR STAPLES
2 x 4 STUDS, 16" ON CENTER
CENTER-ON-STUDS ASSIST NOTCHES
(LINE UP NOTCH EDGES WITH STUD
INNER EDGES TO CENTER CHASSIS
BETWEEN STUDS)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

FSR WB-X1NK-GNG-B Installation guide

FSR
Brand
FSR
Model
WB-X1NK-GNG-B
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents