X5

mettatec X5 User manual

  • Hello! I've reviewed the user manual for the Standalone module, PPK Base y rover , RTK Lora Base y rover and RTK NTRIP Base y rover GNSS receivers. This manual details various operation modes including Standalone, PPK, RTK with Lora and NTRIP connections. Feel free to ask me any questions about the configuration, features or operation of these devices.
  • What is the range of the LoRa connection for RTK corrections?
    What is required to improve the accuracy of a position using PPK mode?
    What is the difference between RTK Lora and RTK NTRIP modes?
PPK Base y rover RTK NTRIP Base y rover
RTK Lora Base y roverStandalone module
Independent device without receiving
corrections from an external source.
Suitable for applications where the required
accuracy is relatively low.
Data collected from the receiver is later
processed to improve the position
accuracy. The use of a GNSS data
processing software is required.
The base station transmits correction
data in real-time to the receiver through
a LoRa connection with a range of up to
10 km (sight line) at 433/915 MHz.
The base station transmits correction
data in real-time to the receiver
through Internet connection with
much greater range
Operation
modes
Dynamic Model:
Portable
Enable Rover mode
Mode: ROVER
Measurement rate:
10 Hz
Configuration STANDALONE
Make sure the PPK
option is enabled
Data format:
NMEA data
In GNSS tab In System tab
Dynamic Model:
Stationary
Dynamic Model:
Portable
Disable Rover mode
Mode: BASE
Measurement rate:
1 Hz
Enable Rover mode
Mode: ROVER
Measurement rate:
10 Hz
Configuration PPK Mode
Base mode Rover mode
In “GNSS” tab, set the data format to “RAW
Data”. If it is required to connect via Bluetooth
to a GIS software, select “Combinated Data”.
In “GNSS” tab In “GNSS” tab
Both modes
Make sure the PPK
option is enabled
At the end of the job, you will have .ubx
files that can be further processed.
Configuration RTK Lora
Base mode Rover mode
In “System” tab, LoRa parameter settings
should be the same for base and rover.
In “GNSS” tab
Make sure the PPK
option is disabled
In “GNSS” tab
Disable Rover mode
Mode: BASE
Data format:
NMEA data
Data format:
NMEA data
Enable Rover mode
Mode: ROVER
Both modes
Dynamic Model:
Stationary
Measurement rate:
1 Hz
Dynamic Model:
Portable
Measurement rate:
10 Hz
Make sure the PPK
option is disabled
Dynamic Model:
Stationary Dynamic Model:
Portable
Data format:
NMEA data
Disable Rover mode
Mode: BASE Enable Rover mode
Mode: ROVER
Enable NTRIP Server
and put your credentials
Keep the NTRIP
Client disabled
Configuration RTK NTRIP
Base mode Rover mode
For the configuration in both modes, make
sure the following parameters:
In “GNSS” tab In “GNSS” tab
In “GNSS” tab
In “System” tab
Both modes
Caster
GNSS
Wi-Fi
Caster connection
through GIS software
RTCM
Wi-Fi
GNSS
HIGHLY RECOMMENDED
Make sure the PPK
option is disabled
Dynamic Model:
Stationary Dynamic Model:
Portable
Data format:
NMEA data
Disable Rover mode
Mode: BASE
Enable NTRIP Server
and put your credentials
Enable Rover mode
Mode: ROVER
Enable NTRIP Client
and put your credentials
Caster
Configuration RTK NTRIP
Base mode Rover mode
For the configuration in both modes, make
sure the following parameters:
In “GNSS” tab In “GNSS” tab
In “GNSS” tab
In “System” tab
Both modes
GNSS
Wi-Fi
Wi-Fi
GNSS
Rover as NTRIP ClientBase as NTRIP Server
PPK Base and rover
RTK NTRIP Base and rover
RTK Lora Base and rover
Standalone module
Bluetooth
USB SerialLoRa radio
1
For visualizing the X5 Receiver status, you can connect the device with a USB cable in order to enter the GIS software.
1
/