Oscar RunCam Thumb Pro is a powerful and versatile action camera capable of capturing stunning 4K videos at 30fps, 2.7K videos at 60fps, and 1080p videos at 120fps. With its wide 155° field of view, built-in gyro stabilization, and support for up to 256GB microSD cards, the RunCam Thumb Pro is perfect for capturing all your adventures in crystal-clear detail. Whether you're recording your next bike ride, skiing trip, or skydiving adventure, the RunCam Thumb Pro has you covered.
Oscar RunCam Thumb Pro is a powerful and versatile action camera capable of capturing stunning 4K videos at 30fps, 2.7K videos at 60fps, and 1080p videos at 120fps. With its wide 155° field of view, built-in gyro stabilization, and support for up to 256GB microSD cards, the RunCam Thumb Pro is perfect for capturing all your adventures in crystal-clear detail. Whether you're recording your next bike ride, skiing trip, or skydiving adventure, the RunCam Thumb Pro has you covered.
Attention: SD card error includes card full, slow card speed, card damage and etc.
Please avoid long video recording in the case of high temperature and no ventilation.
Overheating will aect the peormance of the device and cause the product to operate abnormally.
Automatically turn on when powered on, the red light is always on
Cut the power or long press the button to power o
Click the shutter button to sta recording, the red light ashes
slowly / Click the shutter button again to stop recording, the red
light is always on
Double-click the shutter button quickly to switch between the
recording mode (the red light is always on) and the parameter
settings mode (the green light is always on)
Scan the QR code in the Runcam APP to congure
Thumb Pro Connect ThumbPro to ight controller for operations
Power on/o
Sta/Stop recording
Mode switch
Parameter settings mode
Remote control mode
SD card error Red light keeps ashing fast
Android and IOS APP
Search“RunCam”on Google play and Apple Store,
or download on our website http://www.runcam.com/download
RunCam Thumb Pro
Camera manual
Function indication
Please read this manual carefully before use and keep it in a safe place
MicroUSB
Button （power/shutter button）
Detachable lens protection cover
1.25mm 4P
Indicator light(Red/Green)
2
2
3
5
4
5
3
4
1
1
Micro SD Card
Camera basic operations
ight control
5V
GRX TX
Power supply connection and ight controller connection
Computer Connection
Connect the computer via Micro USB, it will be recognized as a U disk.
Firmware Update
To ensure optimal peormance of the camera, please use the latest rmware version.
Check the link below to update for reference:
https://www.runcam.com/download/ThumbPro
Firmware upgrade status (Red and green lights ashing fast; when the upgrade is
completed, the camera automatically shuts down.)
Specications
Mode Runcam Thumb Pro
Resolution 4K@30fps\2.7K@60fps\1440P@60fps\
1080P@120fps\1080P@60fps
Video Format MP4
Gyro Bulit-in
Sensor IMX577(12MP)
F.O.V OLD VERSION 145°,NEW VERSION 155°
Micro SD Card Capacity 256G Max
Communication Inteace Micro USB
USB Power Input/
Terminal Power Supply DC 5.0V
Remote Control Ua
Dimension 54mm*25.5mm*21mm
Power Consumption 500mA@5V Max
Net Weight 16g
U3 card is recommended (4K@30FPS/2.7K@60FPS/1080P@120FPS
requires U3 or above)
Suppos up to 256G microSD card
Note: Be careful when handling the microSD card, please avoid contact with liquids, dust and debris.
As a precaution, turn o the camera before inseing or removing a microSD card. Please refer to the
microSD card manufacturer's instructions for use within an acceptable temperature range.
Technical Suppo
Please visit: https://suppo.runcam.com
Step 1 Step 2
MicroSD Card
MIXER
CH1 100 I Ail
CH2 100 I Ele
CH3 100 I Thr
CH4 100 I Rud
CH5 100 SA
CH6 100 SB
CH7 100 SD
Roll
Pitch
Pitch
-0.3 6/148/64
Camera (RunCam
Betaflight Configurator
Configurator: 10.0.0
Firmware: BTFL 3.2.3 (Target: OB72) Enable Expert Mode Disconnect
2019-09-16 @ 11:22:53 -- Running firmware released on: Sep 3 2019 12:26:08
2019-09-16 @ 11:22:53 -- Board: SPEEDYBEEF7, version: 0
2019-09-16 @ 11:22:53 -- Unique device ID: 0x4700233237511631313935
2019-09-16 @ 11:22:53 -- Craft name:
2019-09-16 @ 11:22:53 -- Arming Disabled
Hide Log
Scroll
< >
WIKI
Save and Reboot
Ports
No dataflash
chip found
No dataflash
chip found
0.1 V
0.1 V
Gyro
Gyro Accel
Accel Mag
Mag Baro
Baro GPS
GPS Sonar
Sonar
Setup
Setup
Ports
Ports
Configuration
Configuration
Power & Battery
Power & Battery
PID Tuning
PID Tuning
Receiver
Receiver
Modes
Modes
Motors
Motors
OSD
OSD
Blackbox
Blackbox
CLI
CLI
Port utilization: D: 18% U: 1% Firmware: BTFL 4.0.6, Target: SPEEDYBEEF7, Configurator: 10.5.1 (a769d38)
Packet error: 0 I2C error: 0 Cycle Time: 128 CPU Load: 6%
not all combinations are valid. When the flight controller firmware detects this the serial port configurator will be reset.
Do NOT disable Msp on the first serial port unless you know what you are doing. You may have to reflash and erase your configuration if you do.
Identifier Configuration/MSP Serial Rx Telemetry Output Sensor Input Peripherals
115200
115200
115200
119200
115200
115200
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
Disabled
Disabled
Disabled
Disabled
USBVCP
UART1
UART2
UART3
UART4
UART5
Disabled115200 AUTOSmartPort AUTODisabled AUTO
SOFTSERIAL1
FLIP OVER AFTER
CRASH
Add Range
Add Link
Betaflight Configurator
Configurator: 10.0.0
Firmware: BTFL 3.2.3 (Target: OB72) Enable Expert Mode Disconnect
2019-09-16 @ 11:23:25 -- Board: SPEEDYBEEF7, version: 0
2019-09-16 @ 11:23:25 -- Unique device ID: 0x4700233237511631313935
2019-09-16 @ 11:23:25 -- Craft name:
2019-09-16 @ 11:23:25 -- Arming Disabled
2019-09-16 @ 11:23:59 -- EEPROM saved
Hide Log
Scroll
< >
Save
BLACKBOX ERASE
(>30s)
Add Range
Add Link
CAMERA WI-FI
BUTTON
900 1000 1200 1400 1500 1600 1800 2000 2100
CAMERA POWER
BUTTON
CAMERA CHANGE
MODE
AUX 2
Min: 1900
Max: 2100
AUX 3
Min: 1900
Max: 2100
AUX 1
Min: 1900
Max: 2100
900 1000 1200 1400 1500 1600 1800 2000 2100
900 1000 1200 1400 1500 1600 1800 2000 2100
No dataflash
chip found
No dataflash
chip found
0.1 V
0.1 V
Gyro
Gyro Accel
Accel Mag
Mag Baro
Baro GPS
GPS Sonar
Sonar
Setup
Setup
Ports
Ports
Configuration
Configuration
Power & Battery
Power & Battery
PID Tuning
PID Tuning
Receiver
Receiver
Modes
Modes
Motors
Motors
OSD
OSD
Blackbox
Blackbox
CLI
CLI
Port utilization: D: 27% U:29% Firmware: BTFL 4.0.6 Target: SPEEDYBEEF7, Configurator: 10.5.1 (a769d38)
Packet error: 0 I2C error: 0 Cycle Time: 125 CPU Load: 7%
Add Range
Add Link
Add Range
Add Link
Add Range
Add Link
In the Flight Controller Congurator, navigate to the Modes tab. There are new
CAMERA WI-FI, CAMERA POWER and CAMERA CHANGE modes
Assign any available channel to the function you need, for example:
· CAMERA POWER: start/stop the video. When in the OSD of the camera, this is used to
move to the next menu item.
· CAMERA CHANGE MODE: Switch between the recording mode and the QR code
setting mode.
· Assign the AUX2 to the CAMERA POWER, range 1900-2100
· Assign the AUX3 to the CAMERA CHANGE MODE, range 1900-2100
Please choose your Model on the controller, then access to the MIXER interface and
assign the channel to the switch of the controller. Take opentx 2.2.0 for example, assign
the channels CH5, CH6 and CH7 to SA, SB and SD respectively
3. Instructions of the functions of the camera and assigning transmitter channels
to them
4. Assign the channel to the switch of the controller
For example, we connect the Runcam Thumb PRO to the UART 5 interface on the Flight
Controller: connect the Flight Controller to the computer, then open the congurator
software of the Flight Controller. (Open up the congurator that matches the rmware
you are running, Betaight Congurator for Betaight, Cleanight Congurator for
Cleanight). In the Peripherals column of the line UART 5 (on the Ports tab), select
Camera (RunCam Protocol) and click Save And Reboot.
1. Connect the Runcam Thumb PRO with the UART interface of the Flight Controller
2. Make the Flight Controller recognize the Runcam Thumb PRO
Flight Controller UART Control
Preparation
· Firmware: BetaFlight Firmware (≥3.2.0),CleanFlight Firmware(≥2.1.0) ,
KISS Firmware (≥1.3-RC30) or INAV Firmware (≥1.7.3).
· Any available UART interface on the Flight Controller
Power the Flight Controller and the Runcam Thumb PRO
· Set the SA to the bottom, the camera starts/stops the video
· Set the SD to the bottom, the camera switches among the two modes:
video and OSD setting mode
5. Test
Video Bitrate and Codec
Video Quality
High Medium Low
60Mbps 50Mbps 40Mbps
40Mbps 30Mbps 20Mbps
60Mbps 50Mbps 40Mbps
Codec
H.264
4K@30fps
60Mbps 50Mbps 40Mbps2.7K@60fps
1440P@60fps
1080P@120fps
45Mbps 30Mbps 22Mbps1080P@60fps
Resolution
(1) f it cannot be recognized after connecting to the computer, please conrm that there is a
microSD card inseed; if the microSD card cannot be read normally, please t to replace the
USB cable or the computer USB inteace.
Sho press the shutter button to switch to PCCAM
(2) While connecting to a computer, please ensure that it‘s only powered via USB, otherwise it will
damage the computer's USB po or the camera.
-
1
Oscar RunCam Thumb Pro is a powerful and versatile action camera capable of capturing stunning 4K videos at 30fps, 2.7K videos at 60fps, and 1080p videos at 120fps. With its wide 155° field of view, built-in gyro stabilization, and support for up to 256GB microSD cards, the RunCam Thumb Pro is perfect for capturing all your adventures in crystal-clear detail. Whether you're recording your next bike ride, skiing trip, or skydiving adventure, the RunCam Thumb Pro has you covered.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
RunCam Split HD Camera User manual
-
RunCam SPLIT-HD User manual
-
Holybro Kakute F7 #11040 Installation guide
-
Holybro Kakute User manual
-
RunCam P179H29T31LYADQ4 User manual
-
RunCam 5 Orange User manual
-
tbs electronics PowerCube User manual
-
SpeedyBee F405 V3 BLS 50A 30×30 Stack for FPV Drones User manual
-
SpeedyBee F405 WING APP User guide
-
SpeedyBee F7 V3 BL32 50A 30×30 Stack Mini Flight Controller User manual
