RunCam
Split HD
User Manual
MicroSD Slot
Power/ Mode button
Shield
Lens Module Connector
TXGND
+5V
HD Output Connector
(DJI-AirUnit Supported)
Standby/Recording
Status Light (Red)
RX
www.runcam.com
Video Resolution
Video File Format
Image Sensor
Communication Interface
Max Micro SD Card
Supported
Power Input
Working Current
Weight
2.7K@60fps/1440P@60fps 4:3
2.7K@60fps/1080P@60fps
Horizontal Perspective 124°
Field of View(FOV) 154°
Model RunCam Split HD
FPV Resolution 720P@60fps
MP4
SONY 5MP
Supported
Up to 128G. Samsung's U3 card is recommended (2.7K60/1080P120
requires U3 or above; other solutions require U1 or above)
Please make sure that the le format of the SD card is FAT32, otherwise,
it will easily cause errors.
Lens Specs M12*0.5
Lens Module Size 19*19mm
PCB Size 29*30mm
Mounting Hole Distance 20*20mm / 25.5*25.5mm
DC 5V
450mA@5V(Max)
19.9g
1
2
QR Code Setting
Status Light(Green)
GND
TX
RX
5V
GND
RX
TX
5V
（Excluded Product）
DJI-AirUnit
（Excluded Product）
DJI-AirUnit
SpeedyBee F7 V2
（Excluded Product）
Please push the shield a little bit up with one hand like showed in above (step 1) and
then press the SD card(step 2) with another hand to let the card pop out.
Capacity up to 128GB; U3 recommended (2.7K50/1080P120 requires U3 or above;
other solutions require U1 or above)
· Micro SD Card
· Lens Module Connection Diagram
· Instruction Diagram
Powering On/O
Status light-red LED ashes quickly at 0.5 second intervals
Status light-green LED always on
Use RUNCAM APP to enter RunCam Split HD entrance,
Set up and generate a QR code. Scan with camera in QR code mode
QR code, it will automatically switch to standby mode after
setting successfully. Status light red LED
Status light-red LED ashes slowly at 1 second interval
-Short press the power/shutter button to start/stop recording
Double-click the power button in standby mode to switch
between Lopp video and QR code Parameter Setting mode.
Short press the power button to turn on, long press 2S to turn o
Standby Mode Status light-Red LED always on
HD Recording
Firmware Update Status light-red and green LEDs ash at the same time
Mode Switching
Video Mode
QR Code Setting
SD Card Issues
Status light-green LED ashes quickly at 0.5 second intervals
Lens Module
Bad Connection
· Basic Camera Operation
· Power Supply and Remote UART
Control Connection Diagram
Warning: Current Input ≥1A (Don't powered by VTx)
MIXER
CH1 100 I Ail
CH2 100 I Ele
CH3 100 I Thr
CH4 100 I Rud
CH5 100 SA
CH6 100 SB
CH7 100 SD
Roll
Pitch
Pitch
-0.3 6/148/64
Camera (RunCam
Betaflight Configurator
Configurator: 10.0.0
Firmware: BTFL 3.2.3 (Target: OB72) Enable Expert Mode Disconnect
2019-09-16 @ 11:22:53 -- Running firmware released on: Sep 3 2019 12:26:08
2019-09-16 @ 11:22:53 -- Board: SPEEDYBEEF7, version: 0
2019-09-16 @ 11:22:53 -- Unique device ID: 0x4700233237511631313935
2019-09-16 @ 11:22:53 -- Craft name:
2019-09-16 @ 11:22:53 -- Arming Disabled
Hide Log
Scroll
< >
WIKI
Save and Reboot
Ports
No dataflash
chip found
No dataflash
chip found
0.1 V
0.1 V
Gyro
Gyro Accel
Accel Mag
Mag Baro
Baro GPS
GPS Sonar
Sonar
Setup
Setup
Ports
Ports
Configuration
Configuration
Power & Battery
Power & Battery
PID Tuning
PID Tuning
Receiver
Receiver
Modes
Modes
Motors
Motors
OSD
OSD
Blackbox
Blackbox
CLI
CLI
Port utilization: D: 18% U: 1% Firmware: BTFL 4.0.6, Target: SPEEDYBEEF7, Configurator: 10.5.1 (a769d38)
Packet error: 0 I2C error: 0 Cycle Time: 128 CPU Load: 6%
not all combinations are valid. When the flight controller firmware detects this the serial port configurator will be reset.
Do NOT disable Msp on the first serial port unless you know what you are doing. You may have to reflash and erase your configuration if you do.
Identifier Configuration/MSP Serial Rx Telemetry Output Sensor Input Peripherals
115200
115200
115200
119200
115200
115200
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
Disabled
Disabled
Disabled
Disabled
USBVCP
UART1
UART2
UART3
UART4
UART5
Disabled115200 AUTOSmartPort AUTODisabled AUTO
SOFTSERIAL1
FLIP OVER AFTER
CRASH
Add Range
Add Link
Betaflight Configurator
Configurator: 10.0.0
Firmware: BTFL 3.2.3 (Target: OB72) Enable Expert Mode Disconnect
2019-09-16 @ 11:23:25 -- Board: SPEEDYBEEF7, version: 0
2019-09-16 @ 11:23:25 -- Unique device ID: 0x4700233237511631313935
2019-09-16 @ 11:23:25 -- Craft name:
2019-09-16 @ 11:23:25 -- Arming Disabled
2019-09-16 @ 11:23:59 -- EEPROM saved
Hide Log
Scroll
< >
Save
BLACKBOX ERASE
(>30s)
Add Range
Add Link
CAMERA WI-FI
BUTTON
900 1000 1200 1400 1500 1600 1800 2000 2100
CAMERA POWER
BUTTON
CAMERA CHANGE
MODE
AUX 2
Min: 1900
Max: 2100
AUX 3
Min: 1900
Max: 2100
AUX 1
Min: 1900
Max: 2100
900 1000 1200 1400 1500 1600 1800 2000 2100
900 1000 1200 1400 1500 1600 1800 2000 2100
No dataflash
chip found
No dataflash
chip found
0.1 V
0.1 V
Gyro
Gyro Accel
Accel Mag
Mag Baro
Baro GPS
GPS Sonar
Sonar
Setup
Setup
Ports
Ports
Configuration
Configuration
Power & Battery
Power & Battery
PID Tuning
PID Tuning
Receiver
Receiver
Modes
Modes
Motors
Motors
OSD
OSD
Blackbox
Blackbox
CLI
CLI
Port utilization: D: 27% U:29% Firmware: BTFL 4.0.6 Target: SPEEDYBEEF7, Configurator: 10.5.1 (a769d38)
Packet error: 0 I2C error: 0 Cycle Time: 125 CPU Load: 7%
Add Range
Add Link
Add Range
Add Link
Add Range
Add Link
In the Flight Controller Congurator, navigate to the Modes tab. There are new
CAMERA WI-FI, CAMERA POWER and CAMERA CHANGE modes
Assign any available channel to the function you need, for example:
· CAMERA POWER: start/stop the video. When in the OSD of the camera, this is used to
move to the next menu item.
· CAMERA CHANGE MODE: Switch between the recording mode and the QR code
setting mode.
· Assign the AUX2 to the CAMERA POWER, range 1900-2100
· Assign the AUX3 to the CAMERA CHANGE MODE, range 1900-2100
Please choose your Model on the controller, then access to the MIXER interface and
assign the channel to the switch of the controller. Take opentx 2.2.0 for example, assign
the channels CH5, CH6 and CH7 to SA, SB and SD respectively
3. Instructions of the functions of the camera and assigning transmitter channels
to them
4. Assign the channel to the switch of the controller
For example, we connect the RunCam Split HD to the UART 5 interface on the Flight
Controller: connect the Flight Controller to the computer, then open the congurator
software of the Flight Controller. (Open up the congurator that matches the rmware
you are running, Betaight Congurator for Betaight, Cleanight Congurator for
Cleanight). In the Peripherals column of the line UART 5 (on the Ports tab), select
Camera (RunCam Protocol) and click Save And Reboot.
1. Connect the RunCam Split HD with the UART interface of the Flight Controller
2. Make the Flight Controller recognize the RunCam Split HD
· Flight Controller UART Control
Preparation
· Firmware: BetaFlight Firmware (≥3.2.0),CleanFlight Firmware(≥2.1.0) ,
KISS Firmware (≥1.3-RC30) or INAV Firmware (≥1.7.3).
· Any available UART interface on the Flight Controller
Power the Flight Controller and the RunCam Split HD
· Set the SA to the bottom, the camera starts/stops the video
· Set the SD to the bottom, the camera switches among the two modes:
video and OSD setting mode
Please visit: https://support.runcam.com
· Technical Support
5. Test
· Parameter
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Oscar RunCam Thumb Pro User manual
-
THUMB 73E-11215 User manual
-
THUMB 6928352 User manual
-
dji CP.TR.00000004.01 User manual
-
Holybro Kakute F7 #11040 Installation guide
-
Holybro Kakute User manual
-
SpeedyBee F7 35A BLS Mini User manual
-
SpeedyBee F7 35A BLS User manual
-
BetaFPV LiteRadio 2 User manual
-
SpeedyBee F7 User manual