Page is loading ...
1. Remove End Caps and other components which would interfere
with insertion of track nuts, from horizontal supports.
2. Remove lens cover from fixture.
3. Slide mounting brackets in or out to fit horizontal supports.
4. Loosen track nuts*and slide into support rails (Fig. 1).
INSTALLATION INSTRUCTIONS
OVERHEAD WORK LIGHT for WORKSTATIONS
INTRODUCTION: Overhead fluorescent lighting fixture mounts to C-Rail commonly used on workstations. Two styles of mounting
are possible. The standard brackets fit workstation supports from 44"(1118mm) to 68"(1727mm) apart running
perpendicular
to the
light. The addition of “Z” brackets (included) allows mounting to a tool rail running
parallel
to the light so as to aid installation on
benches over 6' (1.8m) in width. This method is detailed on the reverse side. Light includes cord and standard 110 volt, three-prong
plug. No switch is included. Installation of two standard 48" fluorescent tubes (not included) is necessary prior to use. Remove
diffusing lens to install or replace tubes.
STANDARD INSTALLATION
POWER BAR
(purchase separately)
may be mounted to
vertical support columns
at back of bench or
to overhead horizontal
rails. Convenient power
supply for light and
electric tools.
Includes switch.
OVERHEAD WORK LIGHT
Mounted to workstation
horizontal support rails
running perpendicular to
light. See opposite side for
mounting to parallel rails.
Light angle may be adjusted
15Ofore or aft.
WORKSTATION
HORIZONTAL
SUPPORT RAIL
Perpendicular
to light.
10' CORD
with molded
grounded
plug.
4, 5, or 6 ft.
WORK BENCH
5. Position light where desired and tighten track nuts, clamping
fixture in place.
6, Install two 48" fluorescent tubes. (Tubes not included.)
7. Re-install lens cover.
8. Plug cord into convenient 120v electrical outlet.
9. Loosen hand knobs on both ends (Fig. 2) and adjust tilt of light
for optimum work surface illumination. Tighten hand knobs.
LOOSEN HAND
KNOBS (B0TH ENDS)
TO TILT LIGHT
ADJUST LIGHT FOR
BEST WORK SPACE
ILLUMINATION
Figure 1-Bracket Detail Figure 2-Fixture Adjustment
TRACK
NUT*
HORIZONTAL
SUPPORT
RAIL
HORIZONTAL
SUPPORT
RAIL
MOUNTING
BRACKET
BRACKET
FRONT VIEW
*When mounting to structural track such as Unistrut or B-Line, replace track nuts on mounting brackets with two over-sized track nuts, included.
Printed in USA Bulletin No. 630163.c
1. Remove End Cap, and other components which would interfere
with insertion of track nuts, from horizontal support rail.
2. Remove lens cover from fixture.
3. Remove track nuts from mounting brackets. Do not remove bolts
or washers. Install “Z” brackets to mounting brackets (Fig. 3).
Secure with track nuts and original bolts.
4. Loosen track nuts*on “Z” brackets and slide into parallel
support rail (Fig. 3).
PARALLEL RAIL INSTALLATION
ELECTRICAL BOX with OUTLETS (by others).
Bolts to pre-drilled bracket. Provides handy,
out-of-the-way power source for light.
“Z” BRACKETS
included with light kit.
OVERHEAD WORK LIGHT
Optional mounting to C-Rail
running parallel to light.
WORKSTATION SUPPORTS
AND RAILS
PARALLEL RAIL
for light mounting
6 ft. or wider
WORK BENCH
5. Position light brackets so they do not extend beyond ends of light.
6. Position light where desired on rail and tighten track nuts,
clamping fixture in place.
7, Install two 48" fluorescent tubes. (Tubes not included.)
8. Re-install lens cover.
9. Plug cord into convenient 120v electrical outlet.
10. Loosen hand knobs on both ends (Fig. 4) and adjust tilt of light
for optimum work surface illumination. Tighten hand knobs.
LOOSEN HAND
KNOBS (BOTH ENDS)
TO TILT LIGHT
ADJUST LIGHT FOR
BEST WORK SPACE
ILLUMINATION
Figure 3-Bracket Detail Figure 4-Fixture Adjustment
TRACK
NUTS*
TRACK
NUT
TRACK
NUT
RAIL
PARALLEL
RAIL
MOUNTING
BRACKET “Z”
BRACKET
ALTERNATE
“Z” BRACKET
LOCATION
“Z”
BRACKET
FRONT VIEW
MOUNTING TO RAIL RUNNING PARALLEL TO LIGHT
Optional “Z” brackets (included) allow light to be mounted to a
parallel
C-Rail, usually on benches more than 6' (1.8m) in width. This
method requires that “Z” brackets be secured to the standard brackets using the track nuts, bolts and washers already in place.
*When mounting to structural track such as Unistrut or B-Line, replace track nuts on “Z” brackets with two over-sized track nuts, included.
/
