Hardware
Information
Managing your server using
the Advanced System
Management Interface
ESCALA POWER5
REFERENCE
86 A1 36EW 00
BLANK
ESCALA POWER5
Hardware Information
Managing your server using the
Advanced System Management
Interface
July 2006
BULL CEDOC
357 AVENUE PATTON
B.P.20845
49008 ANGERS CEDEX 01
FRANCE
REFERENCE
86 A1 36EW 00
Hardware
The following copyright notice protects this book under Copyright laws which prohibit such actions as, but not
limited to, copying, distributing, modifying, and making derivative works.
Copyright Bull SAS 1992, 2006
Printed in France
Suggestions and criticisms concerning the form, content, and presentation of this
book are invited. A form is provided at the end of this book for this purpose.
To order additional copies of this book or other Bull Technical Publications, you
are invited to use the Ordering Form also provided at the end of this book.
Trademarks and Acknowledgements
We acknowledge the right of proprietors of trademarks mentioned in this book.
AIX® is a registered trademark of International Business Machines Corporation, and is being used under licence.
UNIX® is a registered trademark in the United States of America and other countries licensed exclusively through
the Open Group.
Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries
The information in this document is subject to change without notice. Bull will not be liable for errors contained
herein, or for incidental or consequential damages in connection with the use of this material.
Table of Contents
Managing your server using the Advanced System Management Interface...............................................1
Printable PDF.........................................................................................................................................1
Saving PDF files...............................................................................................................................2
Viewing system information....................................................................................................................2
Viewing vital product data................................................................................................................2
Viewing persistent storage...............................................................................................................3
Viewing system power control network trace...................................................................................3
Viewing progress indicator from previous boot................................................................................4
Viewing progress indicator history...................................................................................................4
Viewing real-time progress indicator................................................................................................5
Controlling the system power.................................................................................................................5
Powering the system on and off.......................................................................................................7
Setting auto-power restart................................................................................................................8
Performing an immediate power off.................................................................................................8
Performing a system reboot.............................................................................................................9
Setting Wake on LAN.......................................................................................................................9
Changing system configuration............................................................................................................10
Changing system name.................................................................................................................11
Changing the processing unit identifier..........................................................................................11
Configuring I/O enclosures.............................................................................................................13
Changing the time of day...............................................................................................................13
Changing firmware update policy...................................................................................................14
Enabling PCI error injection policy.................................................................................................14
Configuring monitoring...................................................................................................................15
Disconnecting an HMC..................................................................................................................15
Changing the interposer plug count...............................................................................................16
Changing the number of HSL Opticonnect Connections...............................................................16
Enabling I/O adapter memory allocation........................................................................................17
Deconfiguring hardware.................................................................................................................17
Configuring virtual Ethernet environment settings.........................................................................21
Programming vital product data.....................................................................................................22
Changing service indicators...........................................................................................................24
Setting performance options.................................................................................................................27
Changing the logical memory block size........................................................................................27
Enabling cache locking mode........................................................................................................28
Configuring network services................................................................................................................28
Configuring network interfaces.......................................................................................................28
Configuring network access...........................................................................................................29
Using extended services................................................................................................................30
Debugging virtual TTY...................................................................................................................31
Using on-demand utilities.....................................................................................................................31
Order Power On Demand..............................................................................................................32
Activate Power On Demand...........................................................................................................32
Resume server firmware after POD activation...............................................................................33
Use Power On Demand commands...............................................................................................33
Viewing information about POD resources....................................................................................33
Using concurrent maintenance utilities.................................................................................................34
Controlling power to IDE devices...................................................................................................34
Preparing the control panel............................................................................................................35
Troubleshooting the server using service aids.....................................................................................36
Displaying error and event logs......................................................................................................36
Enabling serial port snoop..............................................................................................................37
Initiating a system dump................................................................................................................38
Initiating a service processor dump................................................................................................40
Initiating a partition dump...............................................................................................................40
Configuring a system port for call options......................................................................................41
Configuring your modem................................................................................................................42
Configuring the call-home and call-in policy...................................................................................43
Testing the call-home policy...........................................................................................................44
Rebooting the service processor....................................................................................................44
Restoring your server to factory settings........................................................................................45
Entering service processor commands..........................................................................................46
Managing your server using the Advanced System Management Interface
i
Managing your server using the Advanced System Management Interface
ii
Managing your server using the Advanced System Management
Interface
The Advanced System Management Interface (ASMI) is the interface to the service processor that allows you
to set flags that affect the operation of the server, such as auto power restart, and to view information about
the server, such as the error log and vital product data.
This interface is accessible using a Web browser on a client system that is connected to the service processor
on an Ethernet network. It can also be accessed using a terminal attached to a system port on the server. The
service processor and the ASMI are standard on all models and servers models, except for the ESCALA PL
245T/R models. On the ESCALA PL 245T/R models, the SMS menus contain additional options that allow
you to perform system management functions, such as powering off or restarting the system and viewing
diagnostic data.
On the standard systems, you may be able to use the service processor's default settings. In that case,
accessing the ASMI is not necessary.
The following list contains ASMI concepts and tasks that can be performed using the ASMI if you have
successfully logged in with the requisite authority level (for additional details, see ASMI authority levels):
Printable PDF
Print a PDF (Portable Document Format) version of this topic and save it to your workstation.
•
Viewing system information
View system power control network (SPCN) trace data, progress indicator history, and vital product
data (VPD).
•
Controlling the system power
Manually and automatically control the system power.
•
Changing system configuration
View and perform custom system configurations, such as enabling PCI (Peripheral Component
Interconnect) error injection policies, viewing system identification information, and changing memory
configuration.
•
Setting performance options
Enhance the performance of your managed system by changing the logical memory block size and
enabling cache locking mode.
•
Configuring network services
Configure network interfaces, configure network access, and debug the virtual TTY.
•
Using on-demand utilities
Activate inactive processors or inactive system memory without restarting your server or interrupting
your business.
•
Using concurrent maintenance utilities
Replace devices in your server without having to power off your server.
•
Troubleshooting the server using service aids
View and customize troubleshooting information with various service aids (such as viewing error logs
and initiating service processor dumps).
•
Printable PDF
Print a PDF (Portable Document Format) version of this topic and save it to your workstation.
To view or download the PDF version of this document, select Managing your server using Advanced System
Management Interface (about 250 KB).
You can view or download the related topic Managing the Advanced System Management Interface (about
136 KB).
Managing your server using the Advanced System Management Interface 1
Saving PDF files
To save a PDF file on your workstation for viewing or printing:
Right-click the PDF in your browser (right-click the link to the topic).1.
Click Save Target As... if you are using Internet Explorer. Click Save Link As... if you are using
Netscape Communicator.
2.
Navigate to the directory in which you want to save the PDF file.3.
Click Save.4.
Downloading Adobe Reader
You need Adobe Reader to view or print these PDFs. You can download a copy from the Adobe Web site .
Parent topic: Managing your server using the Advanced System Management Interface
Viewing system information
View system power control network (SPCN) trace data, progress indicator history, and vital product data
(VPD).
This ASMI option provides access to vital product data (VPD) and system power control network (SPCN)
trace data.
Attention: Clicking Back in the browser might display outdated data. To display the most up-to-date data,
select the desired item from the navigation pane.
Viewing vital product data
View selected or all manufacturer's VPD, such as serial numbers and part numbers.
•
Viewing persistent storage
Displays the contents of the registry.
•
Viewing system power control network trace
View SPCN trace data that was dumped from the processor subsystem or server drawer.
•
Viewing progress indicator from previous boot
Displays the boot progress indicator from the previous system boot.
•
Viewing progress indicator history
View progress codes that were shown on the control panel display.
•
Viewing real-time progress indicator
Reports the progress codes that currently show on the control panel display.
•
Parent topic: Managing your server using the Advanced System Management Interface
Viewing vital product data
View selected or all manufacturer's VPD, such as serial numbers and part numbers.
You can view manufacturer's vital product data (VPD) stored from the system boot prior to the one in progress
now.
To perform this operation, your authority level must be one of the following:
Managing your server using the Advanced System Management Interface
2 Saving PDF files
General•
Administrator•
Authorized service provider•
To view the VPD, complete the following steps:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand System Information and select Vital Product Data.2.
A list of field replaceable units (FRUs) that exist on the system and their descriptions are displayed.
Select a single FRU or multiple FRUs from this list that you would like to view.
3.
Click Display Details to display the details for selected FRUs, or click Display all details to display
details for all VPD entries.
4.
Parent topic: Viewing system information
Viewing persistent storage
Displays the contents of the registry.
You can gather additional debug information from a failing system by viewing the contents of the registry. The
term registry key can refer to either the key part of a registry entry or the entire registry entry, depending on
the context. The registry key hierarchy and the contents of any key can be viewed in both ASCII and
hexadecimal formats.
Each registry entry is identified by a two-part key. The first part is the component name, and the second part
is the name of the key. For example, the TerminalSize key of the esw_menu component is identified as
menu/TerminalSize. Each registry key also has a value, which is up to 255 bytes of binary data.
To view persistent storage, your authority level must be authorized service provider.
To view the component names of the contents of the registry, do the following:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand System Information and select Persistent Storage.2.
Click the component names to view a list of registry entries.3.
Click the desired registry entry to view the contents of a registry entry.4.
Parent topic: Viewing system information
Viewing system power control network trace
View SPCN trace data that was dumped from the processor subsystem or server drawer.
You can dump the system power control network (SPCN) trace data from the processor subsystem, or server
drawer, to gather additional debug information. Producing a trace may take an extended period of time based
on your system type and configuration. This delay is due to the amount of time the system requires to query
the data.
Note: Due to the amount of time required to produce a trace, select this option only if it is recommended by an
authorized service provider.
Managing your server using the Advanced System Management Interface
Viewing vital product data 3
To perform this operation, your authority level must be one of the following:
Administrator•
Authorized service provider•
To view this trace data, do the following:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand System Information and select System Power Control Network Trace.
Trace data is displayed as single contiguous data in two columns.
2.
View the raw binary data in the left column and an ASCII translation in the right column.3.
Parent topic: Viewing system information
Viewing progress indicator from previous boot
Displays the boot progress indicator from the previous system boot.
You can view the progress indicator that displayed in the control panel during the previous failed boot. During
a successful boot, the previous progress indicator is cleared. If this option is selected after a successful boot,
nothing displays.
To perform this operation, your authority level must be one of the following:
General•
Administrator•
Authorized service provider•
The progress indicator information is stored in nonvolatile memory. If the system is powered off using the
power-on button on the control panel, this information is retained. If the ac power is disconnected from the
system, this information is lost.
To view the progress indicator from the previous boot, do the following:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand System Information.2.
Select Previous Boot Progress Indicator. The results are displayed in the right pane.3.
Parent topic: Viewing system information
Viewing progress indicator history
View progress codes that were shown on the control panel display.
You can view progress codes that appeared in the control panel display during the last boot. The codes
display in reverse chronological order.
To perform this operation, your authority level must be one of the following:
General•
Administrator•
Managing your server using the Advanced System Management Interface
4 Viewing system power control network trace
Authorized service provider•
To view the progress indicator history, perform the following task:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand System Information.2.
Select Progress Indicator History.3.
Select the desired progress indicator to view additional details and click Show Details. The progress
indicator codes are listed from top (latest) to bottom (earliest).
4.
Parent topic: Viewing system information
Viewing real-time progress indicator
Reports the progress codes that currently show on the control panel display.
You can view the progress and error codes that currently display on the control panel. Viewing progress and
error codes is useful when diagnosing boot-related issues.
To perform this operation, your authority level must be one of the following:
General•
Administrator•
Authorized service provider•
To view the progress indicator, perform the following task:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand System Information.2.
Select Real-time Progress Indicator to display a small box that contains the current progress and error
codes. If no value is currently on the control panel, the small box is displayed but remains empty.
3.
Parent topic: Viewing system information
Controlling the system power
Manually and automatically control the system power.
This topic provides information on how to use the ASMI to manually and automatically control the system
power:
Powering the system on and off
View and customize various initial program load (IPL) parameters.
•
Setting auto-power restart
Enable or disable the function that automatically restarts the system.
•
Performing an immediate power off
Power the system off immediately.
•
Performing a system reboot
Reboot your system without a complete system shutdown.
•
Setting Wake on LAN
Enable or disable the function that powers on a system remotely through a local area network (LAN)
connection.
•
Parent topic:
Managing your server using the Advanced System Management Interface
Managing your server using the Advanced System Management Interface
Viewing progress indicator history 5
Managing your server using the Advanced System Management Interface
6 Controlling the system power
Powering the system on and off
View and customize various initial program load (IPL) parameters.
You can start and shut down the system in addition to setting IPL options.
To perform these operations, your authority level must be one of the following:
Administrator•
Authorized service provider•
Several IPL options that you can set pertain to the server firmware. Firmware is an integral part of the server
that is stored in flash memory, whose contents are preserved when the system is powered off. The firmware is
code that automatically starts when the server is turned on. Its main purpose is to bring the server to a state
where it is ready to operate, which means the server is ready to install or boot an operating system. Firmware
also enables the handling of exception conditions in the hardware and provides extensions to the functions of
the server hardware platform. You can view the server's current firmware level on the Advanced System
Management Interface (ASMI) Welcome pane.
This server has a permanent firmware boot side, or P side, and a temporary firmware boot side, or T side.
When updating the firmware, install new levels of firmware on the temporary side first to test the compatibility
with your applications. When the new level of firmware has been approved, copy it to the permanent side.
To view and change IPL settings, perform the following steps:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand Power/Restart Control and select Power On/Off System.2.
Set the following desired boot settings.
System boot speed
Select the speed for the next boot: Fast or Slow. Fast boot results in skipped diagnostic tests
and shorter memory tests during the boot.
Firmware boot side for next boot
Select the side from which the firmware boots the next time: Permanent or Temporary.
Firmware updates should be tested by booting from the temporary side before being copied
into the permanent side.
System operating mode
Select the operating mode: Manual or Normal. Manual mode overrides various automatic
power-on functions, such as auto-power restart, and enables the power button.
AIX/Linux partition mode boot
Select the stopping point during the boot process. This option is applicable only to servers
servers, and is available only if the system is not managed by the HMC. Service mode boot
from saved list is the preferred way to run online AIX diagnostics. Service mode boot from
default list is the preferred way to run stand-alone AIX diagnostics.
This option is applicable only when the managed system is using the manufacturing default
configuration, which is the initial partition setup as received from your service provider. When
the system is not using the manufacturing default configuration, any changes to this option do
not take effect. However, when the system is using the manufacturing default configuration,
you can change the setting for the next restart by changing this option.
Boot to server firmware
Select the state for the server firmware: Standby or Running. When the server is in the server
firmware standby state, partitions can be set up and activated.
System power off policy
Select the system power off policy. The system power off policy is a system parameter that
controls the system's behavior when the last partition (or the only partition in the case of a
system that is not managed by an HMC) is powered off.
Current hyperboot mode state:
This setting appears if the hyperboot feature is activated for the system. The hyperboot mode
states are: capable and enabled. When the hyperboot feature is activated by entering the
activation code, the mode state initializes in the ASMI and displays capable until the system is
restarted. After the system has restarted the state changes to enabled. Any time you restart
the system in the enabled state, it starts in hyperboot mode.
3.
Managing your server using the Advanced System Management Interface
Powering the system on and off 7
Note: This setting can not be changed by using this task. See Using on-demand utilities for
information about entering a feature activation code to enable this feature.
Perform one of the following steps:
Click Save settings to save the selected options. The power state does not change.♦
Click Save settings and power on/off. All selected options are saved and the system turns on
or off. The power-on option is available only if the system is powered off. The power-off option
is available only if the system is powered on.
♦
Click Save settings and continue server firmware boot to save the selected options, and turn
the server firmware on or off. This option is available only if the server firmware is in standby
mode.
♦
4.
Parent topic: Controlling the system power
Setting auto-power restart
Enable or disable the function that automatically restarts the system.
You can set your system to automatically restart. This function is useful when power has been restored and
any backup power supply has recharged after a temporary power failure or after an unexpected power line
disturbance that caused the system to shut down unexpectedly. Auto-power restart will only work if the
"system operating mode" is set to normal in the Power On/Off System settings. For information about setting
the system operating mode, see Powering the system on and off.
When the system restarts, it returns to the state it was in at the time of the power loss. If the system is not
managed by a Hardware Management Console (HMC), the system reboots the operating system. If the
system is managed by an HMC, all of the partitions that were running before the power loss are reactivated.
To perform this operation, your authority level must be one of the following:
Administrator•
Authorized service provider•
To set the auto-power restart function, do the following:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand Power/Restart Control and select Auto Power Restart.2.
Select either Enable or Disable from the selection list. By default, the state for auto-power restart is
Disable.
3.
Click Save settings to save the selected options.4.
Parent topic: Controlling the system power
Performing an immediate power off
Power the system off immediately.
You can power off your system faster by using the immediate power off option. Typically, this option is used
when an emergency power off is needed. The operating system is not notified before the system is powered
off.
Managing your server using the Advanced System Management Interface
8 Setting auto-power restart
Attention: To avoid experiencing data loss and a longer IPL the next time the system or logical partitions are
booted, shut down the operating system prior to performing an immediate power off.
To perform this operation, your authority level must be one of the following:
Administrator•
Authorized service provider•
To perform an immediate power off, do the following:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand Power/Restart Control and select Immediate Power Off.2.
Click Continue to perform the operation.3.
Parent topic: Controlling the system power
Performing a system reboot
Reboot your system without a complete system shutdown.
You can reboot the system.
Attention: Rebooting the system immediately shuts down all partitions.
To perform this operation, your authority level must be one of the following:
Administrator•
Authorized service provider•
To perform a system reboot, do the following:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand Power/Restart Control and select System Reboot.2.
Click Continue to perform the operation.3.
Parent topic: Controlling the system power
Setting Wake on LAN
Enable or disable the function that powers on a system remotely through a local area network (LAN)
connection.
You can power on a system remotely through a local area network (LAN) connection. Wake on LAN can be
enabled for logical partition configurations, as well as nonpartitioned environments.
Managing your server using the Advanced System Management Interface
Performing an immediate power off 9
Note: Wake on LAN is supported on Ethernet port 0. It is not supported on Ethernet port 1. On model server,
use port Un-P1-T5 to enable Wake on LAN. It is not supported on models ESCALA PL 3250R, and ESCALA
PL 6450R.
To perform this operation, your authority level must be one of the following:
Administrator•
Authorized service provider•
To enable or disable Wake on LAN, complete the following steps:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand Power/Restart Control and select Wake On LAN.2.
Select either Enable or Disable from the selection list. By default, the state for Wake on LAN is
Disable.
3.
Click Save settings to save the selected options.4.
Parent topic: Controlling the system power
Changing system configuration
View and perform custom system configurations, such as enabling PCI (Peripheral Component Interconnect)
error injection policies, viewing system identification information, and changing memory configuration.
This topic provides instructions that should be used to view and perform custom system configurations:
Changing system name
Change the name of the system.
•
Changing the processing unit identifier
Change the processing unit ID, also referred to as the processing unit system power control network
(SPCN) ID.
•
Configuring I/O enclosures
View and change various enclosure attributes.
•
Changing the time of day
Display and change the time and date stored by the system.
•
Changing firmware update policy
Configure your system to only allow firmware updates from the selected source.
•
Enabling PCI error injection policy
Change the PCI error injection policy that forces errors to be injected to PCI cards.
•
Configuring monitoring
Configure the server firmware, HMC, and service processor connection monitoring.
•
Disconnecting an HMC
Display and disconnect HMCs connected to the managed system.
•
Changing the interposer plug count
View and change the multiple chip module (MCM) interposer plug count.
•
Changing the number of HSL Opticonnect Connections
View and change the maximum number of Highspeed Link (HSL) Opticonnect Connections allowed
for your system.
•
Enabling I/O adapter memory allocation
Increase the amount of PCI memory space allocated to specified PCI slots.
•
Deconfiguring hardware
Set deconfiguration policies, change processor configuration, change memory configuration, and
clear all deconfiguration errors.
•
Configuring virtual Ethernet environment settings
Specify settings to control your virtual Ethernet environment.
•
Programming vital product data
Program vital product data (VPD) such as system brand, system identifiers, and system enclosure
type.
•
Changing service indicators
Turn off system attention indicator, enable enclosure indicators, change indicators by location code,
•
Managing your server using the Advanced System Management Interface
10 Setting Wake on LAN
and perform an LED test on the control panel.
Parent topic: Managing your server using the Advanced System Management Interface
Changing system name
Change the name of the system.
You can change the name that is used to identify the system. This name helps your support team (for
example, your system administrator, network administrator, or authorized service provider) to more quickly
identify the location, configuration, and history of your server.
To perform this operation, your authority level must be one of the following:
Administrator•
Authorized service provider•
The system name is initialized to the 31-character value Server-tttt-mmm-SNooooooo, where the
substitution characters mean the following:
Characters Description
tttt Machine type
mmm Model number
ooooooo Serial number
The system name can be changed to any valid ASCII string. It does not have to follow the initialized format.
To change the system name, do the following:
In the navigation area, expand System Configuration.1.
Select System Name.2.
Enter the desired system name using the previous naming convention.3.
Click Save settings to update the system name to the new value.4.
The new system name is displayed in the status frame, the area where the logout button is located. If another
method, such as the HMC, is used to change the system name, the status frame does not reflect the change.
Parent topic: Changing system configuration
Changing the processing unit identifier
Change the processing unit ID, also referred to as the processing unit system power control network (SPCN)
ID.
Use this task if you need to change the processing unit identifier (SPCN ID). The processing unit SPCN ID is
used by the SPCN firmware to identify the system type. It is also used to identify the primary service
processor if there are two service processors in the system.
Managing your server using the Advanced System Management Interface
Changing system configuration 11
To perform this operation, your authority level must be one of the following:
Administrator•
Authorized service provider•
Note: This feature is available only when the system is powered off. This operation resets the service
processor.
To change the processing unit identifier, do the following:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand System Configuration.2.
Select Processing Unit Identifier.3.
Enter the desired information into the 2-character text area. Supported processing unit identifiers are
shown in the following table:
Model or expansion unit Processing unit
identifier
7/10 BA
112/85 B4
7/20 BB
ESCALA PL 250R-VL or ESCALA PL 450R-XS C0
ESCALA PL 250R-L and ESCALA PL 250R-L+ or ESCALA PL
450R-VL+
BA
ESCALA PL 250T/R and ESCALA PL 250T/R+ or ESCALA PL
450T/R-L+
B4
ESCALA PL 450T/R and ESCALA PL 450T/R+ or ESCALA PL
850T/R-L+
B5
ESCALA PL 1650R-L+ B2
ESCALA PL 850R/PL 1650R/R+ B2
ESCALA PL 850R/PL 1650R/R+ (with one or more secondary units) B3
5/75 B9
ESCALA PL 3250R and ESCALA PL 6450R B1
50/74 and 50/79 81
50/88 and 05/88 89
50/94 and 52/94 8A
05/95 and 50/95 8B
57/90 88
11D/10 88
11D/11 88
11D/20 8C
Note: Processing unit IDs are not applicable f, ESCALA PL 245T/R, and the D24 and T24 enclosure
models.
4.
Click Save settings to complete the operation.5.
Managing your server using the Advanced System Management Interface
12 Changing the processing unit identifier
Parent topic: Changing system configuration
Configuring I/O enclosures
View and change various enclosure attributes.
After the server firmware has reached the standby state, you can configure I/O enclosure attributes as follows:
List the status, location code, rack address, unit address, power control network identifier, and the
machine type and model of each enclosure in the system.
•
Change the identification indicator state on each enclosure to identify or off.•
Update the power control network identifier, enclosure serial number, and the machine type and
model of each enclosure.
•
Change the identification indicator state of the SPCN firmware in a enclosure to Enable or Disable.•
Remove rack and unit addresses for all inactive enclosures in the system.•
To perform this operation, your authority level must be one of the following:
Administrator•
Authorized service provider•
To configure I/O enclosures, do the following:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand System Configuration and select Configure I/O Enclosures.2.
Select the enclosure and the desired operation. If you select Change settings, click Save setting to
complete the operation.
3.
Parent topic: Changing system configuration
Changing the time of day
Display and change the time and date stored by the system.
You can display and change the system's current date and time. The date and time can only be changed
when the system is powered off. The time is stored as UTC (Coordinated Universal Time), formerly expressed
as Greenwich mean time (GMT).
To perform this operation, your authority level must be one of the following:
Administrator•
Authorized service provider•
Note: You can change the time of day only when the system is powered off.
To change the time of day, do the following:
On the ASMI Welcome pane, specify your user ID and password, and click Log In.1.
In the navigation area, expand System Configuration.2.
Managing your server using the Advanced System Management Interface
Configuring I/O enclosures 13
Select Time of Day. If the system is powered off, the right pane displays a form that shows the current
date (month, day, and year) and time (hours, minutes, seconds).
3.
Change either the date value or the time value or both, and click Update Time Of Day.4.
Parent topic: Changing system configuration
Changing firmware update policy
Configure your system to only allow firmware updates from the selected source.
Note: These options are only valid if your server is managed by an HMC, otherwise the default source for
installing firmware updates is the operating system and setting the source using this method is ignored by the
server.
You can change the source for firmware updates. For example, if you choose the Hardware Management
Console (HMC) as the source for a firmware update, the HMC must be used to perform the update. The HMC
performs all tasks to update the server firmware.
Parent topic: Changing system configuration
Updating firmware on servers
If your server has an HMC attached, the firmware update can only be performed from the HMC. The firmware
update must be initiated from the HMC concurrently (while the system is running), but the update will not be
applied until the server is rebooted. If your server does not have an HMC attached, the firmware update must
be performed from the operating system. The system reboots immediately to apply the update.
Firmware updates for servers are available on the Web. For more information, see Getting fixes in the Service
and support topic.
Enabling PCI error injection policy
Change the PCI error injection policy that forces errors to be injected to PCI cards.
You can enable or disable the injection of errors on the PCI bus. For example, independent software vendors
who develop device drivers can inject errors to test the error handling code in the device driver.
To perform this operation, your authority level must be one of the following:
Administrator•
Authorized service provider•
Note: To inject errors, you will need special hardware in addition to having advanced PCI bus knowledge.
Managing your server using the Advanced System Management Interface
14 Changing the time of day
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Bull Power 5 Management guide
-
-
Bull and Configuring the Hardware Management Console Installing
-
Bull ESCALA Series User manual
-
-
-
-
-
-
Other documents
-
RAD Data comm ASMi-52 User manual
-
IBM Power 780 Technical Overview And Introduction
-
Raritan Raritan ASMI G4 User manual
-
IBM Power 720 Express 8202-E4B Installation guide
-
-
IBM 520Q User manual
-
-
Juniper AMXU GPS EXPANSION POD User manual
-
-
Delta Electronics HMC Series User manual