215-1434 Rev. H; EN 07-523A
© 2008 Bradley Corporation
Page 1 of 6 1/15/08
S19-270HC (Eyewash)
S19-270JC (Eye/Face Wash)
Cabinet-Mounted Swing-Down
Eyewash
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . .2
Installation Instructions . . . . . . . . . . . . . . . . . . .3
S19-270HC Components . . . . . . . . . . . . . . . . .4
S19-270JC Components . . . . . . . . . . . . . . . . . .5
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
S19-270HC shown
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX (262) 251-5817
bradleycorp.com
Installation
2
S19-270HC, S19-270JC Installation
1/15/08 Bradley Corporation • 215-1434 Rev. H; EN 07-523A
WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the
installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to
the eyewash should be “ON” at all times. Provisions shall be made to prevent
unauthorized shutoff.
The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a
minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per
ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to
ensure compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment
per ANSI Z358.1.
For questions regarding the operation or installation of this product, visit
www.bradleycorp.com or call 1-800-BRADLEY.
Product warranties may also be found under ”Product Information” on our web
site at www.bradleycorp.com.
Installation
T
H
IS
S
ID
E
U
P
Packing List
•
•
•
•
P
.O
. Bo
x
3
0
9
,
M
e
n
o
m
o
n
e
e
F
a
lls
,
W
I 5
3
0
5
1
R
T
E
S
T
T
H
I
S
U
N
I
T
E
A
C
H
W
E
E
K
Te
s
t-o
perate v
alv
e(s) each w
eek and
sign
belo
w
.
R
eport an
y m
alfunction
s
im
m
ed
iat
el
y.
Ventil(e) w
ö
c
he
ntlic
h im
Te
s
tbetrie
b prüf
en,
be
stäti
gt
du
rc
h U
nter
sc
hrift. Je
glic
he
S
törun
g sofo
r
t melden
.
Date
Datum
Date
Signed
Unter
sc
hrift
Signe
Date
Date
Date
Signed
Signed
Signed
D
I
E
S
E
S
G
E
R
Ä
T
1
S
T
W
Ö
C
H
E
N
T
L
I
C
H
Z
U
P
R
Ü
F
E
N
.
E
S
S
A
I
H
E
B
D
O
M
A
D
A
I
R
E
Te
s
t le fo
nction
nem
e
nt de
s v
alve
s
c
haque
sem
aine et
signe e
n ba
s.
S'il y
à qu
elqu
e c
ho
se qui ne v
a pa
s fait
un rap
por
t im
m
édia
temen
t.
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
114-051
3
Installation S19-270HC, S19-270JC
Bradley Corporation • 215-1434 Rev. H; EN 07-523A 1/15/08
Installation
Supplies Required:
• 1/2" NPT water supply to inlet on eyewash
• Bolts for cabinet mounting
• Pipe sealant
• Sign-mounting hardware
Step 1: Rough-in
NOTE: Flush the water supply before installation.
1. Rough-in wall opening to the dimensions shown in Figure
1.
2. Rough-in 1/2" NPT water supply at the dimensions shown
in Figure 2.
3. Position unit in wall opening and mount eyewash in wall with four bolts (supplied by installer)
at the locations shown in Figure 2.
4. With cabinet door open, connect supply line using the coupling nut and combination tailpiece.
Refer to Figure 3a on page 4 (for S19-270HC) or Figure 3b on page 5 (for S19-270JC).
5. Mount the safety sign to the wall with appropriate hardware supplied by the installer.
Figure 1
Figure 2
Assembly of Components - S19-270HC
4
S19-270HC, S19-270JC Installation
1/15/08 Bradley Corporation • 215-1434 Rev. H; EN 07-523A
Figure 3a
NOTE: Shown in the “ON” position.
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
114-051
9
P.O. Box 309, Menomonee Falls, WI 53051
R
TEST THIS UNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
10
1.1
1.2
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10 1.11
1.12
1.13
1.14
1.15
1.16
1.17
1.18
3
2
4
5
6
7
8
5
Installation S19-270HC, S19-270JC
Bradley Corporation • 215-1434 Rev. H; EN 07-523A 1/15/08
Assembly of Components - S19-270JC
Figure 3b
NOTE: Shown in the “ON” position.
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
114-051
9
P.O. Box 309, Menomonee Falls, WI 53051
R
TEST THIS UNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
10
1.1
1.2
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.15
1.13
1.14
1.12
3
2
4
5
6
7
8
6
S19-270HC, S19-270JC Installation
1/15/08 Bradley Corporation • 215-1434 Rev. H; EN 07-523A
Parts List
1 S39-679A 1 Swing-Down Sub-Assembly
1.1 S05-092 1 Eyewash Assembly
1.2 107-371 2 Tethered Dust Cover
1.3 113-1075 1 Pipe (Plated)
1.4 118-288 1 Valve Body (Plated)
1.5 125-135 1 O-Ring
1.6 125-120 1 O-Ring
1.7 S39-598 1 Actuator Sub-Assembly, Valve
1.8 192-016 1 Insert, Direction (Plated)
1.9 160-413 1 Screw, Set
1.10 125-001CS 1 O-Ring
1.11 132-047 1 Insert, Flow Control
1.12 125-032 1 Flow Control
1.13 110-115A 1 Hex Nut (Plated)
1.14 125-001DA 1 O-Ring
1.15 131-082 1 Base
1.16 160-428 1 Screw, Set
1.17 113-1058 1 Shank
1.18 110-115 1 Hex Nut
2 142-045A 1 Spacer
3 S39-566 1 Cabinet Assembly
4 169-364 1 90° Elbow
5 S27-110 1 Stop Valve
6 113-006DH 1 Nipple, Close
7 169-639 1 90° Street Elbow
8 169-348 1 Union
9 114-051 1 Safety Sign
10 204-421 1 Emergency Inspection Tag
Item Part No. Qty. Description
Item Part No. Qty. Description
S19-270HC
1 S39-680A 1 Swing-Down Sub-Assembly
1.1 S05-162 1 Eye/Face Wash Assembly
1.2 S53-063 2 Tethered Dust Cover
1.3 113-1075 1 Pipe (Plated)
1.4 118-288 1 Valve Body (Plated)
1.5 125-135 1 O-Ring
1.6 125-120 1 O-Ring
1.7 S39-598 1 Actuator Sub-Assembly, Valve
1.8 192-016 1 Insert, Direction (Plated)
1.9 160-413 1 Screw, Set
1.10 110-115A 1 Hex Nut (Plated)
1.11 125-001DA 1 O-Ring
1.12 131-082 1 Base
1.13 160-428 1 Screw, Set
1.14 113-1058 1 Shank
1.15 110-115 1 Hex Nut
2 142-045A 1 Spacer
3 S39-160 1 Cabinet Assembly
4 169-364 1 90° Elbow
5 S27-110 1 Stop Valve
6 113-006DH 1 Nipple, Close
7 169-639 1 90° Street Elbow
8 169-348 1 Union
9 114-051 1 Safety Sign
10 204-421 1 Emergency Inspection Tag
Item Part No. Qty. Description
Item Part No. Qty. Description
S19-270JC
/
