Bradley S19-220P Installation guide

Bradley
Brand
Bradley
Model
S19-220P
Category
Sanitary ware
Type
Installation guide
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX 262.251 5817
bradleycorp.com
Installation
215-158P Rev. P; ECN 12-05-003C
© 2012 Bradley
Page 1 of 5 10/18/2012
S19-220P
Wall-Mounted Eye/Face Wash
Table of Contents
Pre-Installation Information ....................... 2
Installation Instructions .......................... 3
Assembly of Components ........................ 4
Parts List ..................................... 5
2
S19-220P Installation
10/18/2012 Bradley • 215-158P Rev. P; ECN 12-05-003C
IMPORTANT
Read this installation manual completely to ensure proper installation, then file it with the
owner or maintenance department. Compliance and conformity to drain requirements and
other local codes and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before discarding
any packaging material. If any parts are missing, do not begin installation until you obtain the
missing parts.
Flush the water supply lines before beginning installation and after installation is complete.
Test the unit for leaks and adequate water flow. Main water supply to the eye/face wash should
be “ON” at all times. Provisions shall be made to prevent unauthorized shutoff.
The ANSI Z358.1 standard requires an uninterrupted supply of flushing fluid. Bradley plumbed
emergency fixtures require a minimum of 30 PSI (0.21 MPa) flowing pressure. Flushing fluid
should be tepid per ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly to verify
proper operation. This equipment should be inspected annually to ensure compliance with
ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be trained
regarding the placement and proper operation of emergency equipment per ANSI Z358.1.
For questions regarding the operation or installation of this product, visit www.bradleycorp.
com or call 1-800-BRADLEY.
Product warranties and service parts information may also be found under ”Products” on our
web site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
P.O. Box 309, Menomonee F
alls,
WI 53051
R
TEST THIS
UNIT EACH
WEEK
Test-operate valv
e(s) each week and sign
below.
Report an
y malfunctions immediatel
y.
Ventil(e) wöc
hentlich im
Testbetrieb prüfen,
bestätigt
durch Untersc
hrift. Jeglic
he Störung sofor
t melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST
WÖC
HENTLICH ZU
PRÜFEN.
ESSAI HEBDOMA
DAIRE
Test le fonctionnement des v
alves chaque semaine et
signe en bas. S'il y à quelqu
e chose qui ne v
a pas fait
un rappor
t immédiatement.
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
114-051
3
Installation S19-220P
Bradley • 215-158P Rev. P; ECN 12-05-003C 10/18/2012
Installation
NOTICE! Avoid cleaners containing organic solvents,
alcohols, and hydrocarbons.
Rinse with water after cleaning.
Supplies Required:
• (3) ³⁄₈" wall fasteners and bolts
• Pipe sealant
• Piping to ½" NPT water supply inlet
• Piping to 1¼" NPT drain outlet
• Sign-mounting hardware
• Backflow prevention device as required by UPC,
IPC and/or local plumbing codes
Local codes may require the installation of a
backflow prevention valve to complete proper
installation. Compliance with local codes is the
responsibility of the installer. Valve must be tested
annually to verify that it is functioning properly.
Backflow prevention valves are not included with
the fixture and may be supplied by the contractor or
purchased from Bradley Corporation.
Step 1: Install inlet-drain fitting
The top of the eyewash heads should be 33"–45"
(838mm–1143mm) from the floor.
1. Position the inlet-drain fitting over the 1¼" drain outlet
pipe from the wall. Using the inlet-drain fitting as a
template, mark the bolt hole locations on the wall.
2. OPTIONAL: Install three suitable fasteners (supplied
by installer) for ³⁄₈" bolts in the wall at the marked hole
locations.
3. Bolt the inlet-drain fitting to the wall or wall fasteners
using ³⁄₈" bolts (supplied by installer).
Step 2: Assemble eye/face wash
1. Assemble eye/face wash components as shown on
page 4.
• Apply pipe sealant (supplied by installer) to all
male-threaded pipe joints.
• Use a strap wrench around pipes when
tightening to prevent marring the BradTect®
protective, safety yellow coating.
Step 3: Connect water supply
1. Connect the water supply piping (by installer) to the
½" NPT inlet on the eye/face wash.
2. Connect the tailpiece to the 1¼" NPT drain outlet on
the eye/face wash.
3. Mount the safety sign to the wall using the sign-
mounting hardware supplied by the installer.
All dimensions assume standard
thread engagement. Variations in
manufacturing allow for +/- ¹⁄₈" (3mm)
per threaded joint. To find the tolerance
of a dimension, add the number of
thread joints in between a dimension
and multiply it by ¹⁄₈" (3mm).
2"
(51mm)
8¼"
(210mm)
Wall
2¼"
(57mm)
Ø 10¾"
(273mm)
4"
(102mm)
13⁵⁄₈"
(346mm)
15⁷⁄₈"
(403mm)
7³⁄₈"
(187mm)
7½"
(191mm)
Ø ⁵⁄₁₆"
(8mm)
5¼"
(133mm)
30½"
(775mm)
suggested
height to
floor
36"
(914mm)
suggested
height to
floor
4
S19-220P Installation
10/18/2012 Bradley • 215-158P Rev. P; ECN 12-05-003C
Assembly of Components
P.O. Box 309, Menomonee Falls, WI 53051
R
TEST THIS UNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: (262-251-5817)
http://www.bradleycorp.com
114-051
13
14
1.7
1.5
1.4
1.3
1.2
1.1
1.9
1.10
1.11
1.12
1.8
1.6
1
7
2
5
3
6
5.1
4
8
9
12
11
10
10.1
10.2
10.3
10.4
Items 1.1–1.12 come preassembled as Item 1.
Items 10.1–10.4 come preassembled as Item 10.
1¼" NPT
Drain Outlet
½" NPT
Supply
Inlet
Flow Control
This End
5
Installation S19-220P
Bradley • 215-158P Rev. P; ECN 12-05-003C 10/18/2012
Parts List
Prepack S45-122 includes Items 4, 5, 5.1, 6
Prepack S45-123 includes Items 4, 5.1, 6
Prepack S05-127 includes Items 1.9, 1.10, 1.11, 1.12
Item Part No. Qty. Description
1 S90-304 1 Eye/Face Wash Bowl Assembly
1.1 111-061 1 Inlet Drain Fitting
1.2 124-028 1 Center Seal Gasket
1.3 187-053 1 Stainless Steel Bowl
1.4 173-009 1 Cup Strainer
1.5 S21-073 1 Supply Pipe
1.6 113-1159 1 Spacer, Drain
1.7 S05-100 1 Yoke/Sprayhead Assembly
1.8 107-371 2 Tethered Dust Cover
1.9 269-651 1 Swivel Stem
1.10 124-055 2 Quad Ring
1.11 139-087 1 Spray Ring
1.12 110-199 1 Nut, Acorn
2 113-006LQ 1 Pipe ½" x 3½"
3 169-025 1 Street Elbow ½"
4 128-135 1 Plastic Eyewash Handle
Item Part No. Qty. Description
5 S27-282 1 ½" Ball Valve w/Nut
5.1 110-215 1 Nut Only
6 142-002DA 1 Lockwasher
7 269-167 1 Tailpiece
8 113-006AW 1 ½" Close Nipple
9 269-852 1 Reducing Tee
10 S39-817 1 Hose Spray Assembly
10.1 S27-332 1 Valve, Hose Spray
10.2 S45-2453 1 Service Kit EFW - Black
Sprayheads
10.3 S53-063 1 Tethered Dust Cover
10.4 128-182 1 Handle
11 S89-002 1
Yellow Tube ³⁄₈” x 8’
12 S45-831 1 Clip Prepack
13 114-051 1 Safety Sign
14 204-421 1 Emergency Inspection Tag
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Bradley S19-220P Installation guide

Bradley
Brand
Bradley
Model
S19-220P
Category
Sanitary ware
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents