Dynam Waco Red 1220mm Wingspan - BNP User manual

Type
User manual
DECAL:
ASSEMBLY:
Waco-01 Fuselage
Waco-05 Vertical stabilizer
TGM-05 Vertical Stabilizer
Waco-04 Elevator
TGM-11 Push Rod
Waco-06
Blade Holder
Waco-12 Decal
DYP-1018 12*6 Propeller
DY-1007 9g Servo
DYR-2001 2.4G Receiver
DY-3003 Glue
DY-6015 14.8V 2200mAh
25C Battery
DY8952
Dynam RC
dynam-rc.cn
of
This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Please recycle.
over
CENTER OF GRAVITY(C.G.)
DIRECTIONS FOR ASSEMBLY AND ADJUSTMENT
Wingspan
Length
Flying Weight
Wing Area
Wing Load
Radio System
Power
Battery
: 1270mm (50in)
: 983mm (38.7in)
: 1550g (54.8oz)
: 40.3dm²
: 38.5g/dm²
: 4 Ch TX and 7 Ch RX
: Brushless System
: LIPO, 2200 mAh, 14.8V
Control Throw Setting Suggestion
Elevator Aileron Rudder
14.8V 2200mAh
Li-Po, 25C
(12x6)
Lithium-polymer Battery
2200mAh 14.8V
25C Discharge
Rechargeable Cells
Use li-po charger only
MOTOR
SPARE PART LIST:
BM3720A-KV650
Brushless Motor
BM3720A-KV650-Shaft
Motor Shaft
DY-3004 Servo Horn
Waco-02 Lower Wing Set Waco-03 Upper Wing Set
Waco-08 Landing Gear Set
Waco
-09 Wing Struts
32 4 5 6
Connect the aileron servos with the
Y wires.
1
Secure the landing gear with PA2.5
*10mm screws.
10 11 12
987
Install the horizontal stabilizer and
vertical stabilizer.
Secure the stabilizers with PA2.3*
20mm screw.
13 14 15 16 17 18
Install the propeller.
Connect the elevator push rod as
shown.
Connect the rudder push rod as
shown.
70 75
70 75
7
11
20
6
16
3
9
8
3
15
1
2
6
19
10
18
21
17
22
Waco-10 Glass Fibre Tube
Waco-07 Canopy
Waco-11 Push Rod
Install the landing gear cover with
Double-sided tape.
Secure the rear wheel onto the
fuselage with a 1.5mm hexangular
screwdriver.
Secure the wing struts with PA 2.5*
6mm screws.
(1) Secure the wing with 6*50mm
screw. (2) Secure the stabilizers
with PA2.3*20mm screw.
Secure the side wing struts with
M2*6mm screws.
Install the battery.
Insert the ø8x300mm fiber glass
tube into the left and right wing, and
connect the wings together.
Put the upper wing on struts as
shown.
Secure the upper wing with M2*6m
m screws.
Apply glue on the contact area of
the horizontal stabilizer and vertical
stabilizer, then glue them together.
Connect the aileron push rod as
shown.
ESC-40A
ESC Skylord 40A
DTM-T006 6A Transmitter
skylord
40A ESC
  • Page 1 1

Dynam Waco Red 1220mm Wingspan - BNP User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI