Haier 29FV6NW User guide

Type
User guide

This manual is also suitable for

29FA1029FA10
COLOUR TELEVISION
OPERATING
INSTRUCTIONS
Stage curtain for open and close effect
218 programs stored
Multi-picture modes and sound modes selection
On/Off timer
Child lock
Soft exchange
Appointment
DVD component input
Surround sound
01
0090500881
WARNING AND CAUTIONS
1. When you clean the TV set, please pull
out the power plug from AC outlet.
Or may result in electric shock, fire or
damage to the TV set. Don't clean the
cabinet and the screen with benzene,
petrol and other chemicals.
4. Do not place the TV set near rain
or moisture as it may cause an electric
shock, or the TV set to catch fire. The TV
set must only be used
in dry indoor location.
2. In order to prolong the using life of the
TV set, please place it at a well ventilated
location.
5. The back cover must only be removed
by a registered electrical service person.
Removing the back cover may result in
electric shock, fire or damage to
the TV set.
3. Don't place the TV
set in direct sunlight
or near heat source.
6. If the TV set is not going to be used for
a long time, or there is a severe thunder &
lightening storm, it is recommended that
the TV set be disconnected from the AC
power outlet and the aerial plug
Explanation on the display tube
When the picture tube requires cleaning, please disconnect the power and use a
dry soft cotton cloth. Do not use any cleaner or abrasive cloth.
1
CONTENTS
Warning and cautions................................................................................................1
Basic feature..............................................................................................................2
Technical specification..............................................................................................2
Preparing for operations............................................................................................3
Function buttons and external sockets......................................................................4
AV connections........................................................................................................5
Remote controller guide...........................................................................................6
Power supply............................................................................................................7
Tuning procedure.....................................................................................................7
Picture and audio adjustment function ..................................................................11
Time function.........................................................................................................14
Setting function .....................................................................................................17
Game......................................................................................................................22
Trouble shooting guide..........................................................................................23
BASIC FEATURE
TECHNICAL SPECIFICATION
1.CRT: 29"
2.COLOUR SYSTEM: PAL N TSC4.43/3.58(AV)
3.AUDIO SYSTEM: BG DK I M N
4.POWER SUPPLY: See rating plate
5.POWER CONSUMPTION: See rating plate
6.ANTENNA INPUT IMPEDANCE : 75Ω
7.SOUND OUTPUT POWER: 5W+5W
8.NET WEIGHT(Kg): 4 6
9.NET DIMENSION (mm): 800 × 525 ×598
Supplied accessories:
Infrared remote control handset 1
Battery(AA) 2
Operating instruction 1
Design and specifications are subject to change without notice.
2
Stage curtain for open and close effect
218 programs stored
Multi-picture modes and sound modes selection
On/Off timer
Child lock
Soft exchange
Appointment
DVD component input
Surround sound
Figure A Figure B
Antenna cable
with a plug
Figure C Figure D
Antenna feeder
Antenna adapter
75-300Ω
Coaxial cable(75Ω) twin-lead cable(300Ω)
Antenna connection
Connect an antenna to the antenna socket on
the TV set, we recommend using a Cable TV
system for better picture and audio quality.
1.If you use a coaxial cable(75Ω),insert the
antenna plug (see figure C) into 75Ωsocket
(see figure A).
2.If you use a twin-lead cable(300Ω),please
shape the cable as figure D, and connect the
leads to antenna adapter and then insert the
antenna adapter into the 75Ωsocket(see
figure B).
Power source wire connection
Insert the power plug into AC outlet.
Install and replace batteries of the
remote control unit:
1.Place the remote control unit with the face
down, then open the battery cover of the
unit.
2.Place the two"AA"size batteries, matching
the + and - signs on each battery to the +
and -signs of the battery compartment.
3.Close the cover of the battery compartment.
NOTE:
(1)Don't drop or wet or dismantle the unit.
(2)If you don't intend to use the unit for a
long period or the electricity of the
batteries is used up, remove the batteries
to prevent batteries acid from leaking
into the battery compartment.
(3)Replace the two old batteries at the
same time.
(4)Don't use charge battery (Ni-cd )and
don't mix battery type.
(5)Don't throw your batteries into a fire.
Dispose of your batteries in a required
place.
PREPARING FOR OPERATIONS
3
Antenna
AV CONNECTIONS
5
FUNCTION BUTTONS AND EXTERNAL SOCKETS
4
Remote sensor:Let the remote controller aim here the set can receive remote
control signal.
Power switch:Press the button to turn on the TV set ,press the button again to turn
off the TV set.
Power indicator: The indicator lights when power on.
Menu button
Program up/down button
Volume up/down button
TV/AV
W
R
B
G R
DVD(with DVD component)
W
R
G
B
Direction of signal
whiteleft audio
redC /right audio
blueC
green
video
Y
yellow
r
b
Y
VCR (without S-VIDEO terminal)
Y
W R
T
o
a di
o
u
t
u
o
VCR (with S-VIDEO terminal)
W R
s e
o
t
T
o
-
v
id o
utpu
v
o
u
To
ide
o
tpu
t
o
m
p e t
uT c
o o
n
n
o t
Note:
1.When receives s-video signal, you must remove video signal; when receive
video signal, you must remove s-video signal.
2.When receive front video signal, you must remove back video signal; when
receive back video signal, you must remove front video signal.
1.Front Panel
S-VIDEO
2.The sockets on the rear panel
Antenna socket
Audio/Video socket
S-Video socket
DVD component socket
VIDEO
IN
L AUDIO R
Y
Cb
Cr
OUT
S-VIDEO
VIDEO
IN
L AUDIO R
Y
Cb
Cr
OUT
AUDIO
VIDEO
L
R
CH+
CH-
VOL+
VOL-
TV/AV
MENU
POWER SUPPLY
Power supply (switch on/off to set main power supply).
1.Press power switch button to switch on AC power supply. The red power indicator
will light.
2. Press the power switch button on the remote controller to enter normal receiving
condition when the TV set is in standby condition.
There are Auto-search, Semi-Auto search and
Fine tuning method.
Auto-search
1.Press [MENU] button, let main menu display
on the screen, then press [-VOL+] buttons to select
TUNING item.
2.Press [CH-] button to enter TUNING menu, then
press [-CH+] buttons to select AUTO MEMORY.
3. Press [VOL+] button to make the AUTO MEMORY
mode work, the TV set will begin to search
programs from program number 0.
After the search is finished, program number
0 will display on the screen.
Note: During auto-search, if you want to stop searching,
press [VOL-] button.
TUNING PROCEDURE
Remote controller functions
TV/AV exchanging button
Mute button
Numeric button
One/two/three digital buttons
Picture mode selection
Volume up/dwon button
1
2
3
4
5
6
11
15
16
17
7
Program play-forward button
8
Surround sound selection button
9
10
Volume mode selection
Display button
12
Game start or restart button
13
14
System preset button
Lock preset button
Scan button
DC standby button
18
Sleep timer
Game background selection button
Game exit button
10
6 7
19
20
Calendar display button
REMOTE CONTROLLER GUIDE
17
18
16
3
15
14
13
1 2 3
4 5 6
7 8 9
0
TV/AV
SCAN
LOCK
SYSTEM
DISPLAY
-/--
CALENDAR
MENU
CH+
PRE
STEREO
GAME
BACK
P.STD
S.STD
CH-
VOL- VOL+
1
2
5
4
6
8
9
11
10
12
7
EXIT
MODE
19
20
Program play-backward button
Intell igent button:
The numeric butt on“1”has in tell igent fu nction,
press it for 6s, th en th e TV set will se arc h and sto re
the program automatically. Press 0 button conti nuall y
for 6s, the brig htness, colo r, sh arp ness and ti nt wil l be
adjuste d to the factory preset sta tus automaticall y.
ASM VL 0
STOP
SOUNDPICTURE
SELECT
CONFIRM
TIMER
TUNING
FUNCTION
SELECT
ADJUST
POSITION 01
BAND VL
SKIP OFF
SEARCH DOWN
MFT UP
AUTO MEMORY
49.87 MHZ
TUNING PROCEDURE
Press [MENU] button, let main menu display on the
screen, then press
3.Press [CH-] button to enter TUNING sub-menu. Then
press
4.Press [-VOL+] buttons to start searching.
Semi-Auto search
1.Press [-CH+] buttons or numeric button (0~9) to
select the channel number you need. (For example:
channel 1).
2.
[-VOL+] buttons to select TUNING
item.
[CH-] button to select SEARCH item.
[CH-] button
is to search the program from low FC. [CH+] button is
to search the program from high FC. Repeat above
procedure until you find the channel you need.
5.When you intend to memory another channel in
another position, press [-CH+] buttons to select
POSITION item, and use [-VOL+] button to select
a number you need, then press [CH-] button to
select SEARCH, and repeat fourth
procedure.
8
Skip
After pre-tuning the channel, you can skip the
channel you do not need in order to only select
the channel you want to watch.
1.Press [-CH+] buttons or numeric button(0~9) to
select the channel number skipped(for example:
channel 1).
2.Press [MENU] button, let main menu display on
the screen, then press [-VOL+] buttons to select
TUNING item, then press [CH-] button to enter
TUNING menu.
3.Press [-CH+] buttons to select SKIP item.
4.Press [-VOL+] buttons to set SKIP ON mode.
5.Press [DISPLAY] button to shut off the menu. The
channel number will be skipped when you use
[-CH+] buttons to select channels. But you can
still use numeric button to select the channel
number skipped.
Note:
1.You can use the numeric button to select the
channel number that need recover.
2.Press [MENU] button to let the main menu
appear on the screen, then press [-VOL+]
buttons to select TUNING, and press [CH-]
button to enter TUNING menu, then select SKIP.
3.Press [-VOL+] buttons to set SKIP OFF mode.
9
TUNING PROCEDURE
1
SOUNDPICTURE
SELECT
CONFIRM
TIMER
TUNING
FUNCTION
SELECT
ADJUST
POSITION 01
BAND VL
SKIP OFF
MFT UP
SEARCH DOWN
AUTO MEMORY
49.87 MHZ
SELECT
ADJUST
POSITION 01
BAND VL
SKIP OFF
MFT UP
SEARCH DOWN
AUTO MEMORY
49.87 MHZ
SELECT
ADJUST
BAND VL
SKIP OFF
SEARCH DOWN
MFT UP
POSITION 01
AUTO MEMORY
49.87 MHZ
SELECT
ADJUST
BAND VL
SKIP OFF
SEARCH DOWN
MFT UP
POSITION 01
AUTO MEMORY
49.87 MHZ
SELECT
ADJUST
POSITION 01
BAND VL
SEARCH DOWN
MFT UP
SKIP OFF
AUTO MEMORY
49.87 MHZ
SELECT
ADJUST
POSITION 01
BAND VL
SEARCH DOWN
MFT UP
SKIP OFF
AUTO MEMORY
49.87 MHZ
10
Picture mode selection
You can select the picture mode you need
quickly in five preset modes and a user's
personal set.
Press [ P.STD] button to select the picture
quality you need. There are six picture modes
you can select in turn.
DYNAMIC, STANDARD, MILD, MEMORY,
PICTURE MUTE and COLOR MUTE.
Mode Picture quality
DYNAMIC Rich , Bright Movie
STANDARD Proper color
MILD Soft, Light
MEMORY The picture quality you set
PICTURE MUTE function ( no signal)
COLOR MUTE Black &White picture
Note: If the picture in PICTURE MUTE or COLOR MUTE
status, the TV set will recover to DYNAMIC
status when restart.
Adjust the picture status you need to Memory.
1.
Item Press [VOL-]button
CONTRAST Weak Strong
BRIGHT Dark Bright
COLOR Light Dark
SHARP Soft Sharp
B.B Light green Light purple
Note: Tint is only appear in N signal, the method of adjustment is the same
as above.
Picture mute
Press [MENU] button, let main menu display on
the screen, then press [-VOL+] buttons to select
PICTURE item, then press [CH-] button to enter
PICTURE menu.
2.Press [-CH+] buttons to select the item you want
to adjust, then press [-VOL+] buttons to adjust to
your expect effect. The picture status will be stored
to the COLOR MUTE item.
Press [VOL+]button
PICTURE AND AUDIO ADJUSTMENT FUNCTION
11
TUNING PROCEDURE
Fine tuning
Because of some reasons, if auto searching effect of program
isn't good, please fine tune your TV set.
1.Press [-CH+] buttons or numeric button(0~9)
to select the channel number that need to fine
tune.( For example: channel1)
4.Press and hold [-VOL +] buttons until the effects
of the picture and audio are good.
2.Press [MENU] button, let main menu display on
the screen, then press [-VOL+] buttons to select
TUNING item, then press [CH-] button to enter
TUNING menu.
3.Press [-CH+] buttons to select MFT item.
[VOL -] button is to search program from low FC.
[VOL+] button is to search program from low FC.
1
DY NAM IC
MILD
MEMORY
COLOR MUTE
STANDARD
PICTURE MUTE
SELECT
ADJUST
CONTRAST 100
BRIGHT 50
COLOR 50
B.B ON
SHARP 50
SELECT
ADJUST
POSITION 01
BAND VL
SEARCH DOWN
SKIP OFF
MFT UP
AUTO MEMORY
49.87 MHZ
SELECT
ADJUST
BAND VL
SEARCH DOWN
MFT UP
POSITION 01
SKIP OFF
AUTO MEMORY
49.87 MHZ
12
S.C.C
There is soft exchange function in this TV set, when you set this function is ON
and exchange channels, the picture will fade in/fade out to protect your eyes.
1.Press [MENU] button, let main menu display on
the screen, then press [-VOL+] buttons to select
FUNCTION item, then press [CH-] button to enter
FUNCTION menu.
2.Press [-CH+] buttons to select S.C.C item, then press
[-VOL+] buttons to set the S.C.C ON/OFF.
MUTE function
When you need pay attention to the surround sound or answer the telephone or the
guest to visit, using mute function will be convenient.
1.Press [MUTE] button on the remote controller, the( )
will appear at the bottom of the screen, at this time
the sound will be shut off.
2.If you want to recover the sound, you can press the
MUTE button again or press the [-VOL+] buttons
directly.
13
PICTURE AND AUDIO ADJUSTMENT FUNCTION
Sound mode selection
You can select the sound mode you need from
three modes quickly.
Press [S.STD] button to select the sound quality
you need. There are THEATER, NEWS, MUSIC,
PERSONAL to select in turn.
Volume set function
You can adjust the volume to your preset value
quickly(for example: BASS, TREBLE, BALANCE
or S.WOOFER)
1.Press [MENU] button to let main menu display on
the screen, then press [-VOL+] buttons to select
SOUND item, then press [CH-] button to enter
SOUND menu.
2.Press [-CH+] buttons to select BASS item, then
press [-VOL+] buttons to adjust to your expect
effect. You can adjust the parameters of TREBLE,
BALANCE and S.WOOFER by using the same way.
Note: If you want to adjust the S.WOOFER volume,
you should set the S.WOOFER ON.
THEATERTHEATER
NEWSNEWS
MUSICMUSIC
PICTURE AND AUDIO ADJUSTMENT FUNCTION
PERSONALPERSONAL
SELECT
ADJUST
TREBLE 68
BALANCE ±00
S.WOOFER ON
S.WOOFER 100
BASS 66
LANG. ENGLISH
CURTAIN III
POS. EX.
AUTO OFF OFF
S.C.C OFF
SELECT
ADJUST
SELECT
ADJUST
BASS 66
BALANCE ±00
S.WOOFER ON
S.WOOFER 100
TREBLE 68
SELECT
ADJUST
BASS 66
TREBLE 68
BALANCE ±00
S.WOOFER 100
S.WOOFER ON
Off timer function
When you use OFF TIMER function, you can make the TV set switch to the
standby status in that the appointing timer is coming.
1.Press
[MENU] button to let the main menu display
on the screen, then press [-VOL+] buttons to select
TIMER item.
2.Press [CH-] button to enter TIMER menu, then
press [-CH+] buttons to select OFF TIMER item,
then press [-VOL+] buttons repeatedly to set
ON-TIMER to ONCE, EVERY or OFF.
3.Press [CH-] button to select the next item, at this
time, you can set the off time by pressing [-VOL+]
buttons.
4.Press [-CH+] buttons to select CLOCK item, then
you can set the current time by pressing [-VOL+]
buttons. ( on timer/off timer take this clock as
standard )
TIME FUNCTION
14
15
TIME FUNCTION
Sleep timer function
Using the sleep timer function, the TV set can switch to the standby status
automatically when the TV set restarts after an appointing certain time.
1.The sleep timer can be set 120 minutes longest, and it can
change every 10 minutes unit, there are 12 off timer in all.
2.Press[ ] button, the bottom of the
screen will display the right figure cycle.
On timer function
Using ON TIMER function in the standby status, the TV set can connect power
supply and broadcast the appointing channel number automatically when the
appointing time is coming.
1.Press [MENU] button to let the main menu appear
on the screen, then press [-VOL+] buttons to select
TIMER item, then press [CH-] button to enter
TIMER menu.
2.Press[-CH+] buttons to select ON TIMER item,
then press [-VOL+] buttons repeatedly to set the
ON TIMER to OFF, ONCE or EVERY .
3.Press[-CH+] buttons to select next item. At this
time, press [-VOL+] buttons to set ON TIMER(the
method is the same as OFF TIMER).
4.Press[-CH+] buttons to select POS 00 item, then press
[-VOL+] buttons to set ON/OFF TIMER channel
number(for example 05).
5.Press[-CH+] buttons to select CLOCK item, then
press [-VOL+] buttons to set the current time(the
method is the same as OFF TIMER, ON/OFF
TIMER takes this clock as standard).
SLEEP: OFFSLEEP: OFF
SLEEP: 120MINSLEEP: 120MIN
SLEEP: 110MINSLEEP: 110MIN
SLEEP: 20MINSLEEP: 20MIN
SLEEP: 10MINSLEEP: 10MIN
SELECT
ADJUST
19:00
ON TIMER OFF
22:00
POS 0
CLOCK 1:40
APPOINTMENT
OFF TIMER ONCE
0
0
SELECT
ADJUST
19:00
ON TIMER OFF
22:00
POS 0
CLOCK 1:40
APPOINTMENT
OFF TIMER ONCE
0
0
SELECT
ADJUST
ON TIMER OFF
22:00
POS 0
CLOCK 1:40
APPOINTMENT
OFF TIMER ONCE
19:00
0
0
SELECT
ADJUST
ON TIMER OFF
22:00
POS 0
APPOINTMENT
OFF TIMER ONCE
19:00
0
CLOCK 01:40
SELECT
ADJUST
19:00
22:00
POS 0
CLOCK 1:40
APPOINTMENT
OFF TIMER ONCE
ON TIMER OFF
0
0
SELECT
ADJUST
19:00
22:00
CLOCK 1:40
APPOINTMENT
OFF TIMER ONCE
ON TIMER OFF
POS 00
0
16
17
TIME FUNCTION
Appointing program
1.Press [MENU] button to let the main menu display
on the screen, then press [-VOL+] buttons to select
TIMER item, then press [CH-] button to enter
TIMER menu.
2. Press [-CH+] buttons to select CLOCK item, then
press [-VOL+] buttons to set the current time( the
method is the same as OFF TIMER,
APPOINTMENT takes this clock as standard).
3.Press [CH-] button to select APPOINTMENT item.
Then press [-VOL+] buttons to enter APPOINTMENT
sub-menu.
4.Press [-VOL+] buttons to set the POS. you need
( for example:100).
5.Press [CH-] button to enter TIMER item. Then
press [-VOL+] buttons to set the time. Pressing
[-VOL+] buttons, the time will change with 1
minute unit. Pressing and holding [-VOL+] buttons,
the time will change with 10 minutes unit.
6.Press [CH-] button and repeatedly the fourth and
fifth to set the next POS.l.
7.Press [DISPLAY] button to exit the [TIMER] menu.
When the timer is coming, the TV set will
switch to the channel number you appointed
automatically.
The APPOINTMENT is only valid in ON
TIMER status, it is invalid in AC or DC standby status.
APPOINTMENT
POS. TIME
000 OFF
000 OFF
000 OFF
000 OFF
000 OFF
000 OFF
SETTING FUNCTION
Language selection
1.Press [MENU] button to let the main menu display
on the screen, then press [-VOL+] buttons to select
FUNCTION item, then press [CH-] button to enter
FUNCTION menu.
2. Press [-CH+] buttons to select LANG. item, then
press [-VOL+] buttons to select language, the
character will display with the change of language.
Screen projection function
When the background function is activated and the
TV set receive no signal, the screen will change into
the right figure.(game screen projection picture).
1.Press [MENU] button to let the main menu display
on the screen, then press [-VOL+] buttons to select
PICTURE item, then press [CH-] button to enter
PICTURE menu.
2.Press [CH-] button to select B.B item, then press
[-VOL+] buttons to set the B.B ON.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
SCORE 000
SELECT
ADJUST
19:00
ON TIMER OFF
22:00
POS 0
APPOINTMENT
OFF TIMER ONCE
0
CLOCK 01:40
APPOINTMENT
POS. TIME
1
000 OFF
000 OFF
000 OFF
000 OFF
000 OFF
00 OFF
APPOINTMENT
POS. TIME
1
000 OFF
000 OFF
000 OFF
000 OFF
000 OFF
00 12:58
CURTAIN III
POS. EX.
S.C.C OFF
AUTO OFF OFF
LANG. ENGLISH
SELECT
ADJUST
SELECT
ADJUST
CONTRAST 100
BRIGHT 50
COLOR 50
SHARP 50
B.B ON
SETTING FUNCTION
18
Stage curtain for open and close effect
There are three different method of stage curtain for open and close effect, you
can select according to your need.
1.Press [MENU] button to let the main menu display
on the screen, then press [-VOL+] buttons to select
FUNCTON item, then press [CH-] button to enter
FUNCTION menu.
2. Press [-CH+] buttons to select CURTAIN item, then
press [-VOL+] buttons to select one of I, II or III.
I: stage curtain for open and close effect
II: fade in/fade out
III: mix stage curtain for open and close effect
Calendar function
The calendar of this TV set stores the years from 1901year to
2050 year.
1.Press [CALENDAR] button on the remote controller
the calendar will be displayed on the screen(pressing
it again, you can cancel the on-screen display).
2.Press [-CH+] buttons to adjust year, press [-VOL+]
buttons to adjust month.
SETTING FUNCTION
Exchange
For example: exchange the position of the position number 1 with position
number 9
1.Press [MENU] button to let the main menu display
on the screen, then press [-VOL+] buttons to select
FUNCTION item, then press [CH-] button to enter
FUNCTION menu.
2. Press [-CH+] buttons to select POS.EX item, then
press [-VOL+] buttons to enter POS.EX sub-menu.
The digit of EX.POS1 and EX.POS2 item are the current
position number.
3.Press [-CH+] buttons to select EX.POS2 item, then
press [-VOL+] buttons to input position number 9.
4.Press [-CH+] buttons to select EXCHANGE item,
then press [-VOL+] buttons to enter. At this time,
the program of original position number 1 is
exchanged to position number 9, the program of
original position number 9 is exchanged to position
number 1.
POS.EX
EX.POS2 1
EXCHANGE
RETURN
EX.POS1 1
9
19
JAN 2004
SU MO TU WE TH FR SA
1 2 3
4 5 6 7 8 9 10
11 12 13 14 15 16 17
18 19 20 21 22 23 24
25 26 27 28 29 30 31
POS. EX.
S.C.C OFF
AUTO OFF OFF
LANG. ENGLISH
CURTAIN III
SELECT
ADJUST
LANG. ENGLISH
CURTAIN III
S.C.C OFF
AUTO OFF OFF
POS. EX.
SELECT
ADJUST
POS.EX
EX.POS1 1
EXCHANGE
RETURN
EX.POS2 9
SETTING FUNCTION
SETTING FUNCTION
There is lock function in this TV set, you can select it to protect your TV set
according to your need.
定时关机功能
The password of the TV set is preset "0000" in
manufacture, if you want to change the password,
you can fill in four digits.
Changing password
3.Press numeric buttons and
input four digits.
1.Press [LOCK] button, OSD is
as the right figure.
4. The screen returns to the
original status after inputting
new password(see the right
figure), at this time you can
input new password to enter
password set menu.
LOCK SET UP
PASSWORD: - - - -
LOCK SET UP
TUNING LOCK OFF
PRESET PROG. OFF
AV LOCK OFF
GAME LOCK OFF
CHILD LOCK OFF
MAX.VOLUME OFF
UNLOCK
CHANGE PW.
CHANGE PW.
NEW PW. - - - -
LOCK
1 2 3
4 5 6
7 8 9
0
MENU
CH+
CH-
VOL+VOL-
2.Press "0" button directly for
four times, and enter LOCK
SET UP menu. Press
buttons to select CHANGE PW.
item, then press [VOL+] button
to enter CHANGE PW.
sub-menu.
[-CH+]
LOCK SET UP
PASSWORD: - - - -
20
21
The TV set can lock tuning, preset program,
AV, game and child lock items, if you need to lock
them, you can set as following procedure.
Lock set up
3.Press buttons to
select TUNING LOCK
item, and press [VOL+]
button to select ON or
OFF.
[-CH+]
1.Press [LOCK] button, and
OSD is as the right figure.
LOCK
1 2 3
4 5 6
7 8 9
0
MENU
CH+
CH-
VOL+VOL-
Note:
1.When the tuning lock is on, you should enter password
to enter the tuning menu, meanwhile you cannot exchange
the program and press 1 button to enter auto search.
2. You can set the default program of on timer by using the
function of preset program.
3.When the AV lock is on, the AV terminal is invalid, at this
time, the screen become black screen and remind that it
is locked, the TV set in mute status.
4.When the child lock is on, the screen will remind that
it is in CHILD LOCK status if you press the buttons of
the TV set, and the buttons of this TV set are invalid.
5.When the game lock is on, the [GAME] button on the
remote controller is invalid.
6. The max volume lock can restrict the max volume of the
TV set, if you set the volume lock 50, the max volume of
the TV set is 50, when you press [VOL+] button to adjust
the volume value that is over 50, the volume will not
change with it any more.
2.Press "0" button directly
for four times (or press the
four-digit password you have
changed) to enter LOCK SET
UP menu.
LOCK SET UP
TUNING LOCK OFF
PRESET PROG. OFF
AV LOCK OFF
GAME LOCK OFF
CHILD LOCK OFF
MAX.VOLUME OFF
UNLOCK
CHANGE PW.
LOCK SET UP
PASSWORD: - - - -
CHANGE PW.
NEW PW. - - - -
GAME
When you selectSUBMARINEgame item, enter game mode and the other
buttons (except [GAME], , ) are invalid, unless you exit the
game.
[-VOL+] [-CH+]
Play game:
Instructions of game controlling buttons
2.Use the remote controller to operate yellow
battle ship. Yellow battle ship bump one of
green ship or blue ship or purple ship or red
ship or blue shot. and game is over. Yellow ship
use [MENU] button shoot shots. The shot bumps
green ship or blue ship or purple ship or blue
shot and win 100scores,the shot bumps red ship,
and win 1000 scores.
3.During game or game is over, press [Game] button
and game can restart. Ship obtaining highest
scores wins.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
SCORE 000
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
SCORE 5800
GAME OVER
1.Press [Game] button to enter game.
MENU
CH+
CH-
VOL- VOL+
GAME
MODE
EXIT
Fire button
Up/Down
button
Left/Right
button
Selection buttons of
game background
Game button
Game exit button
Note:1.If the problem can not be fixed after you check above items. DO NOT attempt
to remove the back cover by yourself.
2.If the snapping sound from the cabinet of the TV set can be heard occasionally
because of temperature changing of environment, it is normal, you can use it
reassuringly.
TROUBLE SHOOTING GUIDE
BREAKDOWN PHENOMENON
PICTURE
SOUND
CHECKING
The direction and connection of the
antenna
Direction, station and connection
of the antenna
Interference from electric
appliance. AutomobileMotor,
Vehicle Fluorescence lamp etc.
Volume, Sound mute
The power plug isn't plugged in AC
outlet. The main power isn't turned
on. The setting up of contrast, brig-
htness and volume.
Adjust color control
Adjust channel again
Moving the TV set or using magnetic electric appli-
ance near TV, Which will lead to color spot on sc-
reen. Please remove the electric appliance and cut
off power. After 120 minutes turn the TV on, the pic-
ture will be recovered.
The following problems are not always caused by hardware failure, please use the
follow trouble shooting guide before you call for service:
?
Picture with snow
Color Spot
No Color
No Picture
Normal
Disturb
Double or Triple Image
Noise
Normal
Noise
No Sound
No Sound
Normal Volume
Normal or Weak Volume
Normal Volume
??
Scramble
22
23
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Haier 29FV6NW User guide

Type
User guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI