PACOM PAC-24RM1616 User manual

PACOM
Brand
PACOM
Model
PAC-24RM1616
Category
Power extensions
Type
User manual

PACOM PAC-24RM1616 is a 16 Channel CCTV Power Supply with Dual Volt / Amp meter. It provides 24VAC distributed via sixteen (16) PTC protected outputs for powering CCTV Cameras and other video accessories. The front panel has tri-colour LED status indicators for each output, Green for Open Circuit, Blue for Closed Circuit, and Red for Short Circuit. The rear panel has a voltmeter with an operational range of 5V - 69.9V and an ammeter with an operational range of 200mA -8Amp. The unit has two power on/off switches, one for each of the 8 channels, and a safety clip for the power cord.

PACOM PAC-24RM1616 is a 16 Channel CCTV Power Supply with Dual Volt / Amp meter. It provides 24VAC distributed via sixteen (16) PTC protected outputs for powering CCTV Cameras and other video accessories. The front panel has tri-colour LED status indicators for each output, Green for Open Circuit, Blue for Closed Circuit, and Red for Short Circuit. The rear panel has a voltmeter with an operational range of 5V - 69.9V and an ammeter with an operational range of 200mA -8Amp. The unit has two power on/off switches, one for each of the 8 channels, and a safety clip for the power cord.

CCTV Power Supply Manual
16 Channel =(2 x 8Channel) with Dual Volt / Amp meter
24VAC 1.5U Rack Mount
Model: PAC-24RM1616(S84745)
8
Overview: This PACOM Rack Mount CCTV Power Supplies provides 24VAC distributed
via sixteen (16) PTC protected outputs for powering CCTV Cameras and other
video accessories.
Notes: 2 Power On/Off Switches have been provided for each of the 8 Channels at the
rear of the Rack case
Caution: Always test for correct output voltage ( 24VAC) before connecting power to
cameras or other equipment. Temporarily power up the unit and measure the AC
output voltage to avoid damage to devices. Then disconnect power before connecting
external devices.
1. Mount unit in the desired rack location. To maintain Air Circulation, allow a
minimum gap of 50mm on both sides and above the rack mount unit.
2. Unplug Green terminal connector blocks from their sockets for easy installation.
3. Tech Tip: All Cameras with similar power cable length should be grouped together on
the same terminal block.
4. Connect cameras or other equipment power input cables to the screw terminals side
by side in pairs.
5. Screw the terminals closed, making sure that there are no loose connections. Once
this is done, insert the terminal block back into its correct slot.
6. Select the power on switch A or B for each of the 8 Channels
7. Connect the unit’s power cord to a 240VAC outlet and secure with safety clip. Switch
on power to the unit.
8. Front-panel LEDs should illuminate Green if the Channel is not being used and Blue if
the channel or channels are being used.
Red if the Channel has a short circuit on the output lines.
9. Test the output at the camera end of each power cable to be sure voltage is within
range as specified by the Camera manufacturer.
Tri-Colour LED status indicator for each output:
10. Volt meter operational range 5V - 69.9V
11. Amp meter operational range 200mA -8Amp
For current load > 8 Amps ,<9 Amps Amp Meter display will Flash the current value
For current Load Greater than 9.00 Amps, the Amp Meter display will
read OL= Over Load.
12. RyA and RyB are N/C relay contact.
Front Panel
Rear Panel
PAC-24RM1616(S84745) PAC-24RM1616(S84745)
Green
Blue
Red
Open
Circuit
Closed Circuit
< 120mA load
Short Circuit
PTC Fuse tripped
Procedure for resetting PTC fuse:
• Remove short in the circuit.
• Switch off PSU switches either A or B (relevant to the short) for a period of 30 seconds,
then switch back on and PTC fuse will reset automatically.
24.3
6.55
24.3
5.75
CAUTION: To reduce the risks of electric shock do not open enclosure. There is no user
serviceable parts inside. Refer servicing to qualified service personnel.
Replace fuses with the same type and rating T3A/250V
Rack Mount Mechanical Dimensions 437*277*64mm
2 3
Specifications
PAC-24RM1616(S84745) PAC-24RM1616(S84745)
PAC-24RM1616(S84745)
4 5
12
AWG
55m
14
AWG
35m
16
AWG
22m
18
AWG
14m
20
AWG
9m
22
AWG
8m
12
AWG
73m
14
AWG
46m
16
AWG
29m
18
AWG
18m
20
AWG
12m
22
AWG
7m
12
AWG
110m
14
AWG
69m
16
AWG
44m
18
AWG
27m
20
AWG
18m
22
AWG
17m
12
AWG
138m
14
AWG
87m
16
AWG
55m
18
AWG
34m
20
AWG
22m
22
AWG
21m
12
AWG
184m
14
AWG
116m
16
AWG
73m
18
AWG
46m
20
AWG
30m
22
AWG
29m
24
AWG
32m
24
AWG
16m
24
AWG
10m
24
AWG
8m
24
AWG
6m
24
AWG
5m
24
AWG
3m
22
AWG
43m
20
AWG
44m
18
AWG
69m
16
AWG
109m
14
AWG
174m
12
AWG
276m
22
AWG
86m
20
AWG
87m
18
AWG
137m
16
AWG
218m
14
AWG
348m
12
AWG
552m
24VAC Cable Distance (meters)
24
AWG
65m
22
AWG
103m
20
AWG
175m
18
AWG
260m
16
AWG
414m
14
AWG
659m
12
AWG
1052m
5VA
(208ma)
10VA
(417ma)
20VA
(833ma)
30VA
(1.250ma)
40VA
(1.667ma)
50VA
(2.083ma)
75VA
(3.125ma)
100VA
(4.167ma)
4
12
AWG
55m
14
AWG
16
AWG
22m
18
AWG
14m
20
AWG
9m
22
AWG
8m
12
AWG
73m
14
AWG
46m
16
AWG
29m
18
AWG
18m
20
AWG
12m
22
AWG
7m
12
AWG
110m
14
AWG
69m
16
AWG
44m
18
AWG
27m
20
AWG
18m
22
AWG
17m
12
AWG
138m
14
AWG
87m
16
AWG
55m
18
AWG
34m
20
AWG
22m
22
AWG
21m
12
AWG
184m
14
AWG
116m
16
AWG
73m
18
AWG
46m
20
AWG
30m
22
AWG
29m
24
AWG
32m
24
AWG
16m
24
AWG
10m
24
AWG
8m
24
AWG
6m
24
AWG
5m
24
AWG
3m
22
AWG
43m
20
AWG
44m
18
AWG
69m
16
AWG
109m
14
AWG
174m
12
AWG
276m
22
AWG
86m
20
AWG
87m
18
AWG
137m
16
AWG
218m
14
AWG
348m
12
AWG
552m
24VAC Cable Distance (meters)
24
AWG
65m
22
AWG
103m
20
AWG
175m
18
AWG
260m
16
AWG
414m
14
AWG
659m
12
AWG
1052m
5VA
(208ma)
10VA
(417ma)
20VA
(833ma)
30VA
(1.250ma)
40VA
(1.667ma)
50VA
(2.083ma)
75VA
(3.125ma)
100VA
(4.167ma)
Parallel Output Configuration
Load
Load
Load
By connecting more than 1 output in parallel the normal
current availability can be doubled, tripled or even quadrupled
Normal Current Limit X 2
Normal Current Limit X 3Load
Normal Current Limit X 4
Note : Paralelling of outputs can only be done on the same PCB!
Do not attempt to parallel outputs on seperate PCB’s
PAC-24RM1616(S84745) PAC-24RM1616(S84745)
6 7
Troubleshooting
1. Power does not turn on • Check front panel leds and rear main fuse
• Ensure power cord is firmly in its socket and switch
A and B are in the on position
• Ensure you have 240VAC supply to the Power
Supply Unit
2. led’s are RED even • To reset PTC , turn of power and wait for 30 sec,
then restart unit though there is no short circuit
3. Voltage drop is large • Use thicker guage wire
4. Camera case is hot • Check that the correct voltage is supplied to
the camera
5. Amp Meter display • Power Supply load is approaching maximum current limit
Flashes continously
6. Amp Meter display •
reads OL
Power Supply unit has exceeded its maximum load
capacity. Disconnect 1 or more devices until Amp Meter
shows a reading less than the maximum capacity.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

PACOM PAC-24RM1616 User manual

PACOM
Brand
PACOM
Model
PAC-24RM1616
Category
Power extensions
Type
User manual

PACOM PAC-24RM1616 is a 16 Channel CCTV Power Supply with Dual Volt / Amp meter. It provides 24VAC distributed via sixteen (16) PTC protected outputs for powering CCTV Cameras and other video accessories. The front panel has tri-colour LED status indicators for each output, Green for Open Circuit, Blue for Closed Circuit, and Red for Short Circuit. The rear panel has a voltmeter with an operational range of 5V - 69.9V and an ammeter with an operational range of 200mA -8Amp. The unit has two power on/off switches, one for each of the 8 channels, and a safety clip for the power cord.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents